Instruction manual Digital 9000 System
Table Of Contents
- Digital_9000_Manual_06_2017_EN
- Important safety instructions
- Digital 9000 – System overview
- Delivery includes
- EM 9046 receiver
- EM 9046 CAB cable set
- Antennas and antenna boosters
- GZL 9000 antenna cables
- SKM 9000/SKM 9000 COM radio microphone
- Microphone heads for the SKM 9000 radio microphone
- SK 9000 bodypack transmitter
- Microphones for the SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- CI 1-4 line/instrument cable for the SK 9000 bodypack transmitter
- B 60/B 61 battery packs
- BA 60/BA 61 accupack
- L 60 charger
- Product overview
- EM 9046 receiver
- Antennas and antenna boosters
- GZL 9000 antenna cable
- SKM 9000/SKM 9000 COM radio microphone
- SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- BA 60 accupack
- BA 61 accupack
- B 60 battery pack
- B 61 battery pack
- L 60 charger
- Preparing the EM 9046 receiver for use
- Preparing the A/AB/AD 9000 antennas and/or antenna boosters for use
- Preparing the SKM 9000 radio microphone for use
- Preparing the SK 9000 bodypack transmitter for use
- Preparing the L 60 charger for use
- Cascading several chargers
- Setting up or mounting the charger
- Preparing the Digital 9000 system for use
- Using the EM 9046
- Using the SKM 9000
- Using the SK 9000
- Using the L 60
- Cleaning and maintaining the Digital 9000 system
- If a problem occurs ...
- Specifications
Digital 9000 | 111
If a problem occurs ...
SKM 9000 radio microphone
SK 9000 bodypack transmitter
Problem Possible cause Possible solution
Transmitter cannot
be operated,
“LOCK” appears on
the display panel
Lock mode is
activated
Deactivate the lock mode
(see page 90).
No operation
indication
Batteries are flat or
accupack is flat
Replace the batteries or
recharge the accupack
(see page 94).
No RF signal at the
receiver
Transmitter and
receiver are not on
the same frequency
Perform a frequency scan
(see page 56) and then
synchronize the transmitter
and receiver.
Transmission range
is exceeded
Reduce the distance
between transmitter and
receiving antennas.
Transmitter’s RF
signal is deactivated
(“RF Mute”)
Activate the RF signal
(see page 78).
Audio signal has a
high level of
background noise
or is distorted
Transmitter input
gain is too low/too
high
Adjust the input gain
(see page 82).
Problem Possible cause Possible solution
Transmitter cannot
be operated,
“LOCK” appears on
the display panel
Lock mode is
activated
Deactivate the lock mode
(see page 99).
No operation
indication
Batteries are flat or
accupack is flat
Replace the batteries or
recharge the accupack
(see page 94).
No RF signal at the
receiver
Transmitter and
receiver are not on
the same frequency
Perform a frequency scan
(see page 56) and then
synchronize the transmitter
and receiver.
Transmission range
is exceeded
Reduce the distance
between transmitter and
receiving antennas.
Transmitter’s RF
signal is deactivated
(“RF Mute”)
Activate the RF signal
(see page 86).
Audio signal has a
high level of
background noise
or is distorted
Transmitter input
gain is too low/too
high
Adjust the input gain
(see page 90).