BDA_Titel_A4.ai 28.10.
Contents Contents Important safety instructions .................................................................... 2 The product family ........................................................................................ 5 The frequency bank system ..................................................................... 6 Delivery includes ........................................................................................... 7 Product overview .......................................................
Important safety instructions Important safety instructions 1. Read these instructions. 2. Keep these instructions. Always include these instructions when passing the receiver on to third parties. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
Important safety instructions Hazard warnings on the rear of the receiver The label shown on the left is attached to the rear of the receiver. The symbols on this label have the following meaning: This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the receiver’s enclosure that may be of sufficient magnitude to constitute risk of fire or electric shock. This symbol is intended to alert the user to the risk of electric shock if the receiver is opened.
Important safety instructions Intended use of the receiver Intended use of the EM 3731-II single receiver or the EM 3732-II and EM 3732 COM-II twin receivers includes: • having read these instructions, especially the chapter “Important safety instructions” on page 2, • using the receiver within the operating conditions and limitations described in this instruction manual.
The product family The product family The receivers of the product family ensure highest reception reliability and offer unmatched ease of use. Due to their large switching bandwidth and numerous connection options, these receivers provide maximum flexibility in daily operation.
The product family The frequency bank system The receivers are available in four UHF frequency ranges with up to 184 MHz switching bandwidth: Range N 614 – 798 Range N-GB 606 – 790 Range L 470 – 638 400 Range P 776 – 960 600 800 1000 The receivers have seven frequency banks: Channel Frequency bank 1 1 2 ... 2 3 4 5 6 The receiving frequencies are factorypreset (see enclosed frequency table) and cannot be changed. max.
Delivery includes Distribution of the receiving frequencies within the frequency banks 1 to 6: Frequency Distribution of the receiving frequencies within the bank frequency banks 1 2 3 4 5 6 The varying accumulation of frequencies within the frequency banks allows you to use as many channels as possible in a crowded frequency band.
Product overview Product overview Overview of the EM 3731-II/EM 3732-II/EM 3732 COM-II receivers A True Diversity Receiver EM 3732-II RF B % DEV 300 PEAK 100 100 30 50 10 μV 10 776.000 01.01BANK CH M H z HD P A AF COM RF B % DEV 300 PEAK 100 100 30 50 10 μV 10 776.000 01.01BANK CH M H z HD P AF COM RF-OUT FREQ. RANGE: 776 – 960 MHz EM 3732-II-XXX-X RF-OUT FREQ. RANGE: 776 – 960 MHz A Front panel 1 2 3 4 5 6 7 8 9 0 Rack mount “ears” ¼“ (6.
Product overview Overview of the displays After switch-on, the receiver displays the “Bank/Channel” status display. For further illustrations and examples of the different status displays, refer to page 38. Each display provides information on the operating states of the receiver and those of the received transmitter. 쐃 쐇 A RF 쐋 B % DEV 300 PEAK 100 100 30 10 µV 쐏 50 10 쐂 쐆 776.000 01.
Product overview Reception display The reception display is permanently displayed. If you do not press a button on the receiver, the display will dim after 60 seconds (see page 9). RF level display “RF” for the antennas A 쐃 RF B PEAK 100 100 30 쐋 % DEV 300 The left bargraph 쐃 shows the strength of the received RF signal for antenna A; the right bargraph 쐋 shows the strength of the received RF signal for antenna B.
Product overview Status display 776.000 NAME The status display shows the receiving frequency, the transmitter battery status and – depending on the selection made in the “Display” menu – either the frequency bank and the channel number or the name of the receiver. With the EM 3732 COM-II receiver, the command display can also be displayed within the status display. The contents of the status display can be changed in the “Display” menu (see page 38).
Product overview Command display (status display of the audio outputs AF and Command) AF COM The command display is only available with the EM 3732 COM-II twin receiver. Besides the two audio outputs K and M the EM 3732 COM-II twin receiver also features the two command outputs J and L.
Putting the receiver into operation Putting the receiver into operation Fitting the device feet To ensure that the receiver cannot slip on the surface on which it is placed, four self-adhesive soft rubber feet are supplied. Do not fit the device feet when rack mounting the receiver. CAUTION! Risk of staining of furniture surfaces! Some furniture surfaces have been treated with varnish, polish or synthetics which might cause stains when they come into contact with other synthetics.
Putting the receiver into operation The rack mount “ears” are already fitted to the receiver on delivery. To mount the receiver into a 19" rack: 왘 Slide the receiver into the 19" rack. 왘 Secure the rack mount “ears” 1 to the rack using four screws (not included in the delivery).
Putting the receiver into operation 왘 Unsecure the rack mount “ears” 1 from the rack. 1 -II 왘 Guide the BNC cables through the holes in the rack mount “ears” as shown in the diagram on the left. W 왘 Screw the antenna holders Z to the BNC sockets W using the supplied washers Y and nuts X. W -II Y Z X Z 왘 Secure the antenna holders Z to the handles of the receiver using two of the supplied screws respectively. [ -II \ 왘 Connect the two BNC connectors [ to the BNC sockets O and R at the rear of th
Putting the receiver into operation If the booster supply voltage is switched on (see page 31), it remains switched on even when the receiver is switched off. 왘 Position antennas in the same room in which the transmission takes place! Maintain a minimum distance of 1 m between antennas and a minimum distance of 50 cm between antennas and metal objects (including reinforced concrete walls).
Putting the receiver into operation Connecting the amplifier/mixing console The receiver has transformer balanced audio outputs. 왘 Connect the amplifier/mixing console to the XLR-3 socket AF Out 1 M (left receiver) or to the XLR-3 socket AF Out 2 K (right receiver). K M 왘 Via the operating menu of the corresponding receiver, adjust the level of the audio output to the input of the amplifier or mixing console (see “Adjusting the audio output level” on page 32).
Putting the receiver into operation Connecting the receivers to a PC via Ethernet The receivers can be centrally configured and monitored via a PC and the supplied “Wireless Systems Manager” software. Additionally, you can update the firmware in the receivers. If you want to connect several receivers to the same Ethernet socket of your network, you require a standard 100Base-T Ethernet switch.
Using the receiver Using the receiver Switching the receiver on/off 6.000 .01BANK CH HD P clock save M H z AF COM esc The EM 3731-II single receiver is switched on and off with the button C. The two receivers of the EM 3732-II or EM 3732 COM-II twin receiver are switched on and off together with the button C. The button C is not a mains switch.
Using the receiver To monitor the audio signal of one of the two receivers of a twin receiver: A RF B % DEV 300 PEAK 100 100 30 10 µV 50 10 776.000 01.01BANK CH save M H z HD P AF COM 왘 Press the headphone button 0 of the receiver whose audio signal you want to monitor. sync esc 6 0 To simultaneously monitor the audio signals of both receivers of a twin receiver: 왘 Simultaneously press the headphone buttons 0of both receivers.
Using the receiver save digital audio processing sync esc A RF 10 10 < 5cm % PEA 100 30 sync B 300 µV 5 1 왘 Position the transmitter’s infra-red interface at a max. distance of 5 cm in front of the infra-red interface (sync) A. The transfer starts automatically. During the transfer, the two blue LEDs in the infra-red interface (sync) A flash and the backlighting of the sync button 9 flashes green.
Using the receiver Sorting channels using the “Wireless Systems Manager” software The sorting function of the “Wireless Systems Manger” software allows you change the channel assignment of the receivers at any time and to save this new channel assignment in a scene. 왘 Start the sorting function as described in the instruction manual of the “Wireless Systems Manger” software. 왘 Press and hold the sync button 9 of the receiver to which you want to assign channel 1 for at least 1.5 seconds.
Using the operating menu Using the operating menu Overview of the operating menu Main menu Extended menu Tune Bank.Ch Name Squelch Booster AF Out Clock Command More Display Scan Compander Display IP-Addr MAC Standby Reset Function of the menu Main menu “Tune” Sets a receiving frequency (this frequency is automatically stored in channel “01” of the frequency bank “U” (user bank)) “Bank.
Using the operating menu Working with the operating menu By way of example of the “Tune” menu, this section describes how to use the operating menu. 776.000 01.01BANK CH After switching the receiver on, the status display is shown on the display panel. M H z HD P AF COM Getting into the operating menu 776. 000 MHz 1.01 Tune Bank B.Ch 왘 Press the jog dial 7. The status display is replaced by the operating menu. The “Tune” menu is displayed together with its current setting.
Using the operating menu Overview of the menus Selection mode A RF B % DEV 300 PEAK 100 100 30 10 µV 50 10 Setting mode M H z 776.000 01.01 BANK CH HD P AF COM esc B.Ch 776. 000 MHz 1.01 Tune Bank Receiving frequency 776 UHF 866 1.01 CEL une Bank.Ch Nam Frequency bank and channel 776 MHz B.Ch 777.005MHz UHF save CEL 30 B.Ch Name Squel Adjusting the receiving frequency (last three digits) B.Ch 5.16 848.
Using the operating menu Selection mode 30 quelch q uelch Setting mode +12 AF O Booster +12 dB ooster +12 AF Out +18 dB +12 48 +18 Clock Audio output level Current audio output level Adjusting the audio output level (-10 dB to +18 dB) save 44.1 48 kHz 88.2 96 Ext. 3 18 F Out 2048 Clock Comm Sampling rate of the digital audio signal 44.1 48 kHz 88.2 96 Ext. 48 Current sampling rate 96 Adjusting the sampling rate (44.1, 48, 88.
Using the operating menu Selection mode mmand Setting mode More esc HiD plu Scan Comp Scanning the frequency banks for free channels Bank Free Bank Free Channel list Scan new Scan reset Displaying the last scan result Displaying the list of free channels Bank Free Bank Free Channel list Scan new Scan reset Bank Free Bank Free Channel list Scan new Scan reset 776.
Using the operating menu Selection mode Setting mode HiDyn plus can Compander Dyn us 4 pander Display 4 Disp 10 49 68 75 1 776.000 NAME IP-Ad Status display 776.000 B.CH AF Current status display save 4 splay 192. 168. 0. 0 00 1 1B 6 00 0 IP-Addr MAC 192. 168. 0. 0 Auto Receiver's IP address within the network 4 COM Selecting the contents of the status display 192. 168. 0. 1 Auto 192. 049. 068. Selecting IP bytes or “Auto” 0192. 168. 0.
Adjustment tips for the operating menu Adjustment tips for the operating menu The following adjustment tips apply to the operating menus of all receivers of the product family. Setting the receiving frequency Via the “Tune” menu, you can: 776. 000 1.01 Tune Bank B.Ch • set the receiver to a receiving frequency that can be freely selected within the preset frequency range. The receiving frequencies are tuneable in 5-kHz steps within the switching bandwidth of 184 MHz max.
Adjustment tips for the operating menu Freq. occupied B.Ch 776.000 MHz 1. You can only select channels that are not occupied. If, during the last scan, channels were detected that were occupied, these channels are marked with a warning triangle and “Freq. occupied”. 왘 After you have selected the frequency bank and the channel, press the save button 8. The selected frequency bank and the selected channel are set. The display changes to the selection mode of the operating menu.
Adjustment tips for the operating menu 왘 After you have entered the six characters of the name, press the save button 8. The name is stored. The display changes to the selection mode of the operating menu. In order that the name is displayed on the status display, you may have to change the status display (see “Selecting the status display” on page 38).
Adjustment tips for the operating menu 왘 Change to the setting mode of the “Booster” menu. The current setting starts flashing. Booster Feed On 왘 Turn the jog dial 7 to change the setting to “Booster Feed On” or “Booster Feed Off”. 7 8 DEV 777.005 U.01 BANK CH save M H z HD P AF COM digital audio processing sync esc sync 왘 Press the save button 8. The selected setting is stored. When the booster supply voltage is switched on, the two LEDs N and S light up.
Adjustment tips for the operating menu 44.1 48 kHz 88.2 96 Ext. 48 왘 Turn the jog dial 7 to select the desired sampling rate. 7 8 DEV 777.005 U.01 BANK CH save M H z HD P AF COM digital audio processing sync esc 왘 Change to the setting mode of the “Clock” menu. The current setting starts flashing. 왘 Press the save button 8. The selected sampling rate is stored. The display changes to the selection mode of the operating menu. sync If you select “Ext.
Adjustment tips for the operating menu Via the “Command” menu, you can determine which of the audio and command outputs will be switched on and off when the command button on the transmitter is pressed.
Adjustment tips for the operating menu Scanning the frequency banks for interference-free channels Via the “Scan” menu, you can scan all frequency banks for free channels. HiD plu Comp Scan 왘 Change to the setting mode of the “Scan” menu. The following selection appears: Channel list Scan new Scan reset – “Channel list” displays the number of free channels for each frequency bank from the last scan.
Adjustment tips for the operating menu Starting the scan Via the “Scan new” menu, you can scan all frequency banks for free channels. The last scan result is overwritten. 왘 Before starting the scan, switch all transmitters of your system off, since channels used by switched-on transmitters will not be displayed as “free channels”. 왘 Turn the jog dial 7 until the arrow points to “Scan new”. Channel list Scan new Scan reset 왘 Press the jog dial 7 to start the scan.
Adjustment tips for the operating menu Multi-channel operation Combined with Sennheiser 3000 and 5000 series transmitters, the receivers can form transmission links that are suitable for multi-channel operation. CAUTION! Risk of reception interference! If – within the receiver’s frequency range – transmitters transmit on channels from different frequency banks, reception can be subject to interference and inter-modulation.
Adjustment tips for the operating menu Selecting the status display Via the “Display” menu, you can select the status display: Dyn us 10 49 68 75 4 pander Display IP-Ad Selectable status display 1. 2. 3. 4. 777.005 U.
Adjustment tips for the operating menu To automatically obtain an IP address (dynamic IP addressing): 왘 Change to the setting mode of the “IP-Addr” menu. The first byte starts flashing. 왘 Press the jog dial 7 repeatedly until the arrow points to “Auto”. 왘 Press the save button 8. 왘 Switch the receiver off and on again (see page 19). The new IP address becomes effective. Displaying the network address (MAC address) 192. 168. 0.
Cleaning the receiver Loading the factory-preset default settings Via the “Reset” menu, you can reset the current settings to the factorypreset default settings. 000 OFF andby Reset Reset to factory defaults ? DEV 776.000 01.01BANK CH save M H z HD P 000 AF COM esc digital audio processing sync sync 왘 Change to the setting mode of the “Reset” menu. The query “Reset to factory defaults?” appears. The green backlighting of the save button 8 flashes.
Additional information Additional information HiDyn plus™ (HDP) or HDX noise reduction RF link Inherent noise of the RF link Transmitter Receiver This product family is equipped with the Sennheiser noise reduction systems HDP and HDX. Both compander systems operate on the same principle (described in the following for HDP) but use different parameters (e.g. time constant, type of control). HDP reduces RF interference.
Additional information Diversity reception The receivers operate on the “true diversity” principle: A receiving antenna receives not only the electromagnetic waves which reach it by a direct path, but also the reflections of these waves which are created in the room by walls, windows, ceilings and fittings. When these waves are superimposed, destructive interference occurs, which can also be called “field strength gaps”. Repositioning the receiving antenna can bring a solution.
If a problem occurs If a problem occurs Problem Possible cause Possible solution No operation indication No mains connection Check the connections of the mains cable. No RF signal Transmitter and receiver are not on the same channel Set transmitter and receiver to the same channel (see “Selecting a frequency bank and a channel” on page 29 and “Synchronizing a transmitter with the receiver” on page 20). The transmission range is exceeded Reduce the distance between transmitter and receiver.
Accessories Accessories Cat. No. Accessory Cat. No. Accessory 502195 A 3700 active broadband antenna, omni-directional 004368 GA 3030 AM antenna mount 087969 502197 AD 3700 active broadband antenna, directional Antenna daisy chain cable, 50 Ω, BNC, 0.25 m 087972 502196 AB 3700 antenna booster Word clock daisy chain cable, 75 Ω, BNC, 0.
Specifications Specifications RF characteristics Modulation wideband FM Frequency ranges Range L: Range N: Range N-GB: Range P: Receiving frequencies (per receiver RX 1 or RX 2) 6 frequency banks with up to 59 factory-preset frequencies each, 1 frequency bank with up to 60 freely selectable frequencies (tuneable in 5-kHz steps) Switching bandwidth up to 184 MHz Frequency stability ≤ ±2.5 ppm Receiver principle true diversity Sensitivity (with HDP, peak deviation) typ. 1.
Specifications Overall device Current consumption max. 0.4 A Power consumption with receiver switched on: max. 20 W (50 VA) with receiver switched off, booster supply voltage switched on: max. 9.5 W with receiver and booster supply voltage switched off: max. 4 W Mains connector 3-pin, protection class I, as per IEC/EN 60320-1 Dimensions W x D x H [mm] 436 x 215 x 44 (without rack mount “ears”) Weight approx. 4080 g (incl. rack mount “ears”) approx.
BDA_Rückseite_A4.ai 28.10.2010 11:16:00 C M Y CM MY CY CMY K Sennheiser electronic GmbH & Co. KG Am Labor 1, 30900 Wedemark, Germany www.sennheiser.com Printed in Germany, Publ.