Instruction manual - Digital 6000 (v4.0)
Table Of Contents
- The Digital 6000 Series
- Products in the Digital 6000 series
- Accessories
- Installing Digital 6000 series devices
- Installing the EM 6000
- Connectors on the rear of the device
- Connecting/disconnecting the EM 6000 to/from the power supply system
- Connecting the EM 6000 to a network
- Outputting analog audio signals
- Outputting digital audio signals
- Outputting audio via a Dante™ network (EM 6000 DANTE only)
- Connecting the word clock
- Connecting remote antennas
- Connecting rod antennas
- Installing the EM 6000 in a rack
- Installing the SKM 6000
- Installing the SK 6000
- Installing the SK 6212
- Installing the L 6000 | LM 6060 | LM 6061 | LM 6062
- Using Digital 6000 series devices
- Using the EM 6000
- Operating elements on the front of the device
- Switching the EM 6000 on and off
- Displays on the EM 6000 display panel
- Buttons for navigating through the menu
- Home screen
- Muting the audio signal
- Setting options in the menu
- Menu structure
- Frequency menu item
- Name menu item
- Sync Settings menu item
- Encryption menu item
- Command Mode menu item
- Scan & Auto-Setup menu item
- Walktest menu item
- AF Output menu item
- Test Tone menu item
- Bank Edit menu item
- System menu item
- System -> Transmission Mode menu item
- System -> Wordclock menu item
- System -> Network menu item
- System -> Device ID menu item
- System -> Dante Settings (only EM 6000 DANTE) menu item
- System -> Booster Feed menu item
- System -> Brightness menu item
- System -> Auto Setup menu item
- System -> Info menu item
- System -> Hardware menu item
- System -> Help menu item
- System -> TX Update menu item
- System -> Reset menu item
- Using the headphone output
- Updating the firmware of the receiver
- Updating the firmware of the Dante™ interface
- Status messages
- Using the SKM 6000
- Using the SK 6000
- Using the SK 6212
- Using the L 6000
- Switching the L 6000 on and off
- Charging rechargeable batteries
- Meaning of the LEDs on the L 6000 charger and LM 6060, LM 6061 and LM 6062 charging modules
- Preparing rechargeable batteries for storage (storage mode)
- Resetting settings (factory reset)
- Updating the firmware
- Operating the L 6000 via a network
- Establishing a radio link
- Synchronizing devices
- Overview
- Recommendations for using antennas
- Equidistant frequency grid
- Link Density mode
- Word clock scenarios for digital audio (AES3 and Dante™)
- Overview
- Product variants
- Specifications
- Cleaning and maintenance
Using the EM 6000
141
Status messages
In certain situations, the EM 6000 display may show status messages and
error messages. For messages relating to errors that can impair function,
the red triangle to the right of the display for the particular channel also
lights up.
No Link
No transmitter connected.
▷ Check the transmitter radio link with the receiving channel. See „Estab-
lishing a radio link“.
Low Signal
The reception quality between the transmitter and receiver is poor (RF A or
RF B below -85 dBm, LQI between 1 % and 19 %)
▷ Check the transmitter’s radio link to the receiving channel and switch
to a different frequency if necessary. See „Establishing a radio link“.
▷ Check that the antennas are positioned correctly. See „Connecting re-
mote antennas“, „Connecting rod antennas“, or „Recommendations for
using antennas“.
Low battery
The transmitter’s batteries or rechargeable battery pack have little battery
life remaining (less than 30 minutes).
▷ Replace the rechargeable battery or batteries.
Sync ok
The synchronization of the receiving channel with the transmitter was suc-
cessful.
Sync Fail
No Frequency
The auto setup function cannot provide any more free frequencies for the
transmitter frequency range.
Sync Fail
Frequency Rejected
The transmitter frequency range is incompatible with the frequency set in
the receiving channel.
▷ Set a different frequency in the receiving channel. See „Frequency
menu item“.