e 965 Instruction manual
Delivery includes Delivery includes • e 965 • MZQ 800 microphone clamp • pouch • quick guide • safety guide Product overview 2 1 5 4 3 0 -10 dB 1. Sound inlet basket 2. XLR-3 connector 3. Directivity switch 4. Sensitivity switch 5.
Installation Installation Attaching the microphone Screw the microphone clamp to a stand. Place the microphone with its back end into the microphone clamp. Orient the microphone together with the microphone clamp. Connecting the microphone Connect the XLR-3 socket of the microphone cable (optional accessories) to the XLR-3 socket of the microphone. Using the windshield Place the MZW 4032 (optional accessories) windshield over the microphone head.
Operation Operation Holding the microphone If you cover the microphone head during transmission, this will change the pick-up pattern of the microphone and consequently the sound. Only hold the microphone by its body.
Operation Positioning the monitor loudspeakers To prevent feedback and crosstalk, postion your monitor loudspeakers in the angle area of the highest cancellation of the microphone (cardioid: 180°; super-cardioid: 135°).
Operation Using the microphone CAUTION DANGER OF DAMAGE TO THE MICROPHONE! The switches on the microphone can be damaged if you try to operate them using tools. Only operate the switches on the microphone using your fingers. Unscrew the sound inlet basket. Adjusting the pick-up pattern Set the directivity switch to the desired position: Pos. Pick-up pattern Cardioid A cardioid pick-up pattern also picks up sound from the sides. This pattern is good for picking up several vocalists at once, e.g.
Cleaning and maintaining the e 965 Cleaning and maintaining the e 965 CAUTION LIQUIDS CAN DAMAGE THE ELECTRONICS OF THE PRODUCT! Liquids entering the housing of the product can cause a short-circuit and damage the electronics. Keep all liquids away from the product. Do not use any solvents or cleansing agents. Disconnect the products from the power supply system and remove rechargeable batteries and batteries before you begin cleaning. Clean all products only with a soft, dry cloth.
Specifications Specifications Transducer principle externally polarized dual-diaphragm condenser microphone Membran diameter 25.4 mm/1" Frequency response 40 - 20,000 Hz Pick-up pattern cardioid/super-cardioid, switchable Sensitivity (free field, no load) with preattenuation 7 mV/Pa 2.3 mV/Pa Nominal impedance (at 1 kHz) 50 Ω Min. terminating impedance 1 kΩ Max. sound pressure level (at 1 kHz) with preattenuation 142 dB 152 dB Equivalent noise level 21 dB(A) Phantomspeisung 48 V / 3.
Specifications Frequency response BV 40 50 60 70 80 10 ,0 00 20 ,0 00 H z 20 ,0 00 H z 2, 00 0 2, 00 0 10 ,0 00 1,0 00 1,0 00 5, 00 0 50 0 50 0 0°, 1 m PAD 5, 00 0 20 0 20 0 10 0 50 90 BV 40 50 60 70 80 10 0 50 90 0°, 1 m PAD Connector assignment 1 3 2 + XLR 1 3 XLR + + 2 3 + 1 XLR 2 2 3 1 XLR + + BALANCED 6.
Overview of applications Overview of applications Primary application Secondary application e 602 II e 604 e 608 e 609 silver e 614 e 835 e 845 e 865 e 901 e 902 e 904 e 906 e 908 e 914 e 935 e 945 e 965 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • e 965 | 10/10