User's Manual

ManualsBrandsSennheiser Electronic ManualsAudio EquipmentDigital Wireless Headphones System (RS 175/185/195)

Putting the RS 185 into operation

RS 185 | 17

Inserting or replacing the rechargeable batteries

1 Lightly twist the ear pads counterclockwise until you overcome a slight

resistance.

2 Lift the ear pads off the ear cups to reveal the ba

ttery compartments.

3 Insert the rechargeable batteries in

to the compartments. To replace the

batteries, pull the batteries out of the compartments and insert the

new ones. Be sure to observe correct polarity when inserting the bat-

teries. Please dispose old batteries as special waste or return them to

your specialist dealer.

4 Hook the ear pads onto the ear cups. A

s you put back the ear pads,

observe th

e L (left) and R (right) markings on the rear of the ear pads.

5 Twist the ear pads clockwise until you hear a cli

ck sound. Ensure that

they are locked firmly onto the ear cups.

You can also power the headphones using standard batteries (AAA

size, 1.5 V). Note however, that standard batteries are not recharge-

able, and if you are using non-rechargeable batteries, you must not

place the headphones on the headphones holder.

NEW

Summary of content (9 pages)

PAGE 1
Putting the RS 185 into operation Inserting or replacing the rechargeable batteries 1 Lightly twist the ear pads counterclockwise until you overcome a slight resistance. 2 Lift the ear pads off the ear cups to reveal the battery compartments. 3 Insert the rechargeable batteries into the compartments. To replace the batteries, pull the batteries out of the compartments and insert the new ones. Be sure to observe correct polarity when inserting the batteries.
PAGE 2
Putting the RS 185 into operation Charging the rechargeable batteries CAUTION Danger of damage to the headphones! If you insert non-rechargeable batteries into the battery compartments, the batteries may leak during charging and can damage your headphones. 왘 Do not place the headphones on the headphones holder if you are using non-rechargeable batteries. 8.5h In general, a complete charging cycle takes about 8.5 hours.
PAGE 3
Putting the RS 185 into operation Adjusting the headband For good sound quality and best possible wearing comfort, the headband has to be adjusted to properly fit your head. The headphones feature an adjustable headband with a snap-in locking mechanism for easy adjustment. 왘 Wear the headphones so that the headband runs over the top of your head. Observe the L (left) and R (right) markings on the outer headband when putting the headphones on.
PAGE 4
Using your RS 185 headphone system Using your RS 185 headphone system Switching your wireless headphone system on WARNING Danger due to high volume levels! Listening at high volume levels can lead to permanent hearing defects. 왘 Before putting the headphones on and before toggling between your audio inputs, adjust the volume on the headphones to a low level. Toggling between different inputs may cause enormous volume jumps that can damage your hearing.
PAGE 5
Using your RS 185 headphone system Selecting an audio input If both analog and digital audio inputs are connected to different audio sources, the headphone system enables you to toggle between the two inputs. 왘 Push the AUDIO INPUT SELECTION switch up to listen to an audio source connected to the digital optical input (see page 13). 왘 Push the AUDIO INPUT SELECTION switch down to listen to an audio source connected to the analog input (see pages 14 and 15).
PAGE 6
Using your RS 185 headphone system Adjusting the balance The balance buttons allow you to adjust the volume on the left or right channel of your headphones. Adjust the balance so that you hear comfortably or equally well with both ears. 왘 Press the Balance R button or the Balance L button to increase or decrease the volume on your right (R) or left (L) ear. When the minimum or maximum balance setting is reached, you hear a beep in the headphones.
PAGE 7
Using your RS 185 headphone system Controlling the input level of analog signals The RS 185 headphone system offers two modes (Automatic Level Control ALC/Manual Level Control MLC) for controlling the input level of analog signals going through the system. Level control Definition Automatic Level Control ALC The Automatic Level Control ALC automatically adjusts the sensitivity of the analog input.
PAGE 8
Using your RS 185 headphone system Using the Manual Level Control (MLC) mode WARNING Danger due to high volume levels Before putting on the headphones and before toggling between the level modes, adjust the volume on the headphones to a low level. Toggling between different modes may cause an enormous volume jump that can possibly damage your hearing. Follow these steps to adjust the signal of your analog audio input.
PAGE 9
Using your RS 185 headphone system Pairing one or several headphones to the transmitter The headphones and the transmitter enclosed in this package have been paired from the factory. The following procedure is only necessary if you have cleared all pairing information from your wireless headphone system and you want to revive the lost pairing, or if you want to pair another set of headphones to the transmitter. You can connect up to 2 paired headphones simultaneously with your TR 185 transmitter.