Installation Instructions

1.Customer:SeniorGroupLLC
2.ModelNumber:MFCREMOTE2
3.

4.MainFunctionality:
1)BluetoothLETransmissionforCommunicationtoSTB‐RealtekRTL8752‐Profile(s):HIDforControl/BatteryServiceforBatteryLevel
2)BluetoothClassictobeusedexclusivelyforVoiceCommand/AudioStreamingtoSTB‐RealtekRTL8763‐Profile:HeadSetProfile(HSP)
3)InfraredURCLibraryforTVandCAB(SupportBrands/DevicesofExistingIRRemote)
4)InfraredLearningforCodesnot inURClibraries
5)MicrophoneforVoiceCommand/AudioStreaming.
6)AddTALKButtonforActivating/DeactivatingVoiceCommand/AudioStreaming
5.Function&CodeTable
Key
Number
KeyName
Device
Type
Transmission
Type
CodeType
0 UP mFCSTB BLE Fixed
1 LEFT mFCSTB BLE Fixed
2 OK mFCSTB BLE Fixed
3 RIGHT mFCSTB BLE Fixed
4 DOWN mFCSTB BLE Fixed
5 VOL+ TVURC IR URC/Learn
6 CH+ CABURC IR URC/Learn
7 VOL‐ TVURC IR URC/Learn
8 CH‐ CABURC IR Fixed
9 BRAND mFCSTB BLE Fixed
10 TV mFCSTB BLE Fixed
11 TALK mFCSTB BTClassic Fixed
12 POWER TVURC IR URC/Learn
6.FeedbackLEDBehavior
1)OKLED:ONduringanypressofOKbuttonandusedasfeedbackLED
2)TVLED:ONduringanypressofTVbutton
3)BRANDLED:ONduringanypressofBRANDbutton
4)TALKLED:ONwhenpressedtoenterTALKmode.OFFwhenpressedagaintoexitTALKmode.
5)POWERLED:ONduringanypressofPOWERbutton
6)PAIRINGLED:TurnonafterPairingButtonispressed.AfterPairingisCompleteedandthenTurnsOFF.
7.ToprogramtheTVURCLibrary
1)PressandHoldLeftandPOWERfor3seconds
2)FeedbackLEDwillturnON
3)Selectthebrandcodefromthebrandlistandenteritusingthepre‐definednumbervaluesinthetablebelow.
4)TheFeedbackLEDwillblinkeachtimeabuttonispressedandwillturnOFFandtheremotewillexitprogrammode.
Ifavalidcodeisentered,theremotewillsendtheTVVolumeupcommandandtheLEDblink3timesandthenexitoutofprogrammingmode.
Ifaninvalidcodeisenteredortheremotetimesoutafter5seconds,theLEDwillblink5timesandexitoutofprogrammingmode
8.ToprogramtheCABURCLibrary
1)PressandHoldRightandPOWERfor3seconds.
2)ThefeedbackLEDwillturnON
3)Selectthebrandcodefromthebrandlistandenteritusingthepre‐definednumbervaluesinthetablebelow
4)ThefeedbackLEDwillblinkeachtimeabuttonispressedandwillturnOFFandtheremotewillexitprogrammode
Ifavalidcodeisentered,theremotewillsendtheSTBChannelupcommandandtheLEDblink3timesandthenexitoutofprogrammingmode.
Ifaninvalidcodeisenteredortheremotetimesoutafter5seconds,theLEDwillblink5timesandexitoutofprogrammingmode
9.TolearnanIRcode
1)PressandHoldUPandPOWERfor3seconds
2)ThefeedbackLEDwillblinkingcontinulosly
3)PressthebuttonontheGCRremotetolearnthecommandfromtheoriginalremoteandtheLEDwillturnon
4)PointtheoriginalremotecontrolthefrontoftheGCRremotecontrolandpressthebuttontobetaughttotheGCR
5)ThefeedbackLEDwillblinkthreetimesifthecodeislearnedsuccessfullyandexitoutoflearningmode
6)TheGCRwillblink5timesifthecodeisnotlearnedsuccessfully
7)Continuesteps1through5untilallcodesarelearnedcorrectly
10.TopairremotetoSTB(RemotetobepairedwithSTBatFactory)
1)PressOKbuttononremotecontrol.
2)Pairing(OK)LEDwillturnonuntilpairedwithSTB.
3)TheremotewillbepairedwithBLEdeviceoftheSTB.
4)IftheBLEdeviceispairedoftheSTB,itwillautomaticallywillbepairedwiththeBTdeviceagain.
5)TheTALKLEDwillturnonwhenpairedwithtwodevices.
6)PresstheTALKbutton,TheTALKLEDwillturnoffandexitoutofpairingmode.
*.PairingReset
1)PressandHoldPOWERandDOWNfor3secondsandOKLEDswillblinksthreetimesandturn‐off.
2)TheRCUwillresetthepairedinformationoftheSTB.
11.TouseTalkMode(VoiceCommand)
1)PressandReleaseTALKbutton.
2)TALKbuttonLEDwillturnONandremainON.
3)RemotewilltransmitAudioinfomrationfromMICtoSTBthroughBluetoothClassicusingHandsFreeProfile.
4a)PressandreleaseTALKbuttontoexitTalkMode.
4b)STBsendsSTOPcommandtoRemote.(Alternative‐RemotewilltimeoutwhennolongerreceivingdatafromSTB)
5)TALKbuttonLEDwillturnOFFandremotewillswitchtoBLEforcontrolofSTB.
12.RCUresetmode
1)PressandHoldOKandBRANDbuttonfor3secondsandalloftheLEDswillblinksthreetimesandturn‐off.
2)TheRCUwillresetallinformationandreturntothefactorydefault.
13.ImageandKeyNumberLayout
14. FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Information
Model : mFC-BTR-01
Procuct : mFC Bluetooth Remote GEN1 Manufacturer : Hyun Seung I&C Co., Ltd
Power : DC3 V
FCC ID : 2AVO6-MFCBTR01
IC : 26009-MFCBTR01
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment must not be co-located or operating in conjunction with any other antenna or transmitter
except those has been evaluated to comply with FCC requirements.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
15. IC Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
This radio transmitter 26009-MFCBTR01 has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
This device complies with the safety requirements for RF exposure in accordance with RSS-102 Issue 5 for
portable use conditions.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Le présent émetteur radio 26009-MFCBTR01 a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.
Cet appareil est conforme aux exigences de sécurité concernant l’exposition aux RF selon la norme
RSS-102, 5ème édition, pour des conditions d’utilisation portable.
Informations sur l'antenne
Nom de l'antenne: CC2480
fréquence : 2.4GHz ISM Band
Impédance: 50 (Ω)
Gain (dBi): 3.3 dBi
Type de connecteur: PCB
Antenna Information
Antenna name : CC2480
Frequency : 2.4GHz ISM Band
Impedance : 50 (Ω)
Gain(dBi) : 3.3 dBi
Connector Type : PCB