8800
PREFACE Thank you for purchasing our dual band portable two way radio. This easy-to-use radio will deliver you secure, instant and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio.
Contents Unpacking And Checking Equipment Unpacking and Checking Equipment 01 Product Overview 02 Function Keypad 03 Before Use 05 Charging the Battery Pack 05 Charger LED indicator and charging status 05 USB Charging 06 Battery LED Indicator and battery status 06 Preparation 07 Installing/Removing the Antenna 07 Installing/Removing the Belt Clip 07 Installing/Removing the Battery Carefully unpack the transceiver.
Product Overview Function Keypad 2 4 5 NFOV No. Part Name No.
Function Keypad Before Use Charging the Battery Pack 7 No. Key 7 【PF1】 Function LAMP Key, Short press to turn on/off flashlight Long press for emergency alarm Use only the charger and battery specified by the manufacturer. The charger LED indicates the charging progress. 3 9 : 9 : 【PTT-1】 【PTT-2】 【PF2】 Press PTT-1 key to transmitting A Band Press PTT-2 key to transmitting B Band 4.The indicator light turns to green, the charging is completed.
Before Use USB Charging Use only the USB charging cable specified by the manufacturer. Charger LED can indicate the charging status. Preparation Battery LED Indicator and battery status LED indication Charging status Constant Red Charging Constant Green Fully Charged Installing/Removing the Belt Clip Installing/Removing the Antenna Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
Preparation Status Indication Installing the Optional Speaker/Microphone(or Headset) LED Indicator Insert the speaker/microphone (or headset) plugs into the speaker/microphone jacks.
Basic Operations Powering On/Off Turn the 【Power/Volume knob】 clockwise to switch the transceiver power ON till a click is heard. Adjusting the Volume Rotate the 【Power/Volume knob】 to adjust the volume. Turn clockwise to increase the volume and counter-clockwise to decrease the volume. Enter/Exit Menu Short Press 【MENU】 Key to enter menu, and press 【UP/DOWN】 key to select the function. Press 【MENU】 Key to confirm, Press 【EXIT】 to exit.
Basic Operations Search Operation(SE): Scanning will stop after it detects an active signal. Note: In channel mode, scanning the channel numbers in the channel list. In frequency mode, scanning in frequency steps. PTT-ID This feature allows you to know who call you. Transmit ANI code or DTMF code through DTMF. DTMF code total 15 groups. In the PC software--Edit--DTMF setting, each signal or A/B band can independently select the call code group to be sent.
Troubleshooting Menu Functions Menu CTCSS/DCS Frequency Mode Channel Storage Frequency Reset Function/Description Available settings Receive DCS OFF/D023N...D754I Transmit CTCSS OFF/67.0HZ...241.HZ Transmit DCS OFF/D023N...D754I Encryption ON/OFF Step 2.50/5.00/6.25/10.00/12.50/25.00/50KHz Direction None/Plus/Minus Offset 00.000....69.990MHz CH-Memory 000,CH-001....CH-127 CH-Delete 000,CH-001....
Care and Cleaning Troubleshooting Phenomena Unable to communicate with other members. Irrelevant communication or noise is heard on the channel. The noise is too loud. 16 Analysis Solution You may be too far away from the group members. Move towards other members. You may be interrupted by radios using the same frequency. Change the frequency, or adjust the squelch level. The radio may be set with no signaling. Set signaling for all member radios to avoid interference at the same frequency.
Care and Cleaning NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.