User's Manual

ManualsBrandssengled ManualsElectronicsSengled Wifi Module

User Manual MX1290 V2

MX1290 MX1290V2 is a highly integrated and high performance, low power

consumption includes the ARM architecture M4F kernel processor and 1 x12. 4 GHZ

WIFI single frequency subsystem and power management unit of SoC chip. Leaped up

to 133 MH2 (MX1290) / 62.5 MH2 (MX1290V2), while the SoC integration with internal

256 KB SRAM, 512 KB ROM, it also contains UART, I2C, PWM, SPI and abundant

peripheral interface, only need to provide the DC voltage of 3.3 V, a 40 MHZ crystals

and Flash can work outside. Wi-fi subsystem contains 802.11 b/g/n rf, baseband,

media access control (MAC) design, satisfy the application of low power consumption

and high throughput.Based on intelligent hardware dedicated operating system at the

same time the chip support - MiCO secondary application development, MiCO is a

microcontroller based Internet operating system, based on the software, users can

more easily control 1 ot intelligent device hardware .

⚫ Kernel： ARM Cortex-M4F, 32-bit

⚫ Frequency:MX1290 133MHz/ MX1290V2 62.5MHz

memory

⚫ 256KB SRAM

⚫ 512KB ROM

FLASH controller

Support SPI, Dual SPI, Quad SPI, QPI, DIO

A NOR FLASH MEMORY INTERFACE MODE

⚫ provides 32KB SRAM Cache

⚫ supports memory mapped access to QSPI flash memory devices

Support SPI, Dual SPI, Quad SPI, QPI, DIO

Peripheral interface

⚫ 2X high-speed user serial port (1X can be reused with debugging serial port)

⚫ 1x debug serial port

⚫ 1x SPI interface supports Master mode

⚫ 2x I2C, support Master/Slaver mode

⚫ 1x internal RTC

⚫ 6 x PWM

⚫ can support up to 13 GPIO ports

⚫ 1 x SWD

Summary of content (7 pages)

PAGE 1
User Manual MX1290 V2 MX1290 MX1290V2 is a highly integrated and high performance, low power consumption includes the ARM architecture M4F kernel processor and 1 x12. 4 GHZ WIFI single frequency subsystem and power management unit of SoC chip. Leaped up to 133 MH2 (MX1290) / 62.5 MH2 (MX1290V2), while the SoC integration with internal 256 KB SRAM, 512 KB ROM, it also contains UART, I2C, PWM, SPI and abundant peripheral interface, only need to provide the DC voltage of 3.
PAGE 2
IC Warning This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device.
PAGE 3
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 4
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
PAGE 5
2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g.
PAGE 6
2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
PAGE 7
2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.