User's Manual

ManualsBrandsSenao Networks ManualsElectronicsWireless 802.11 ac/a/b/g/n Access Point

Quick Installation Guide

CAP7250AG/CAP7252AG/CAP7253AG

Wireless-AC+ABGN Long Range Ceiling Mount Dual Concurrent AP

Please verify contents of the box before continuing to set up the CAP7250AG/CAP7252AG/CAP7253AG.

 CAP7250AG/CAP7252AG/CAP7253AG Access Point

 12V/2A 100V~240V Power Adaptor

 Mounting Bracket

 Wall/Ceiling Mounting Hardware Kit

 T-Rail Mounting Hardware Kit

*CAP7250AG is 3x3 concurrent 3x3 MIMO access point

*CAP7252AG is 2x2 MIMO internal ANT access point

*CAP7253AG is 2x2 MIMO external ANT access point

Connecting the CAP7250AG/CAP7252AG/CAP7253AG

1) Ensure that the computer in use has an Ethernet Card (RJ-45 Ethernet Port). For more information,

verify with User Manual.

2) Connect one end of the Category 5e Ethernet cable into RJ-45 port of the

CAP7250AG/CAP7252AG/CAP7253AG and the other end to the RJ-45 port on the computer that

will use the CAP7250AG/CAP7252AG/CAP7253AG. Ensure that the cable is securely connected to

both the CAP7250AG/CAP7252AG/CAP7253AG and the Computer.

3) Connect the Power DC Inlet to the DC-IN port of the CAP7250AG/CAP7252AG/CAP7253AG and

the Power to the electrical out.

Note: CAP7250AG/CAP7252AG/CAP7253AG supports both IEEE 802.3at PoE(Power over Ethernet) and

regular power adapter. You should use either one as the power source. Please do not apply both at the

same time.

Summary of content (6 pages)

PAGE 1
Quick Installation Guide CAP7250AG/CAP7252AG/CAP7253AG Wireless-AC+ABGN Long Range Ceiling Mount Dual Concurrent AP Please verify contents of the box before continuing to set up the CAP7250AG/CAP7252AG/CAP7253AG.
PAGE 2
IP address configuration 1) After ensuring the EnGenius device is powered on and plugged in, ensure that your computer is on. 2) For the next steps, refer to your Operating System User Manual. 3) Once your computer is on, ensure that your TCP/IP is set to On or Enabled. (In the control panel, double click Network Connections and then double click on the connection of your Network Interface Card (NIC). Select Internet Protocol (TCP/IP) and then click on the Properties button.
PAGE 3
Switching Between Operating Modes This device can operate in the following modes: Access Point, WDS AP, WDS Bridge and Repeater. A. Click on the Operation Mode link under the System navigation drop-down menu. B. Operating Mode: Select an operating mode from the list (Access Point, WDS AP, WDS Bridge or Repeater) and then click on the Apply button. C. All basic setup is completed. Note: The wireless connection is not secure.
PAGE 4
To attach the CAP7250AG/CAP7252AG/CAP7253AG to a ceiling using the provided T-rail connectors: 1) Attach the T-rail connectors to the bottom cover of the CAP7250AG/CAP7252AG/CAP7253AG using the provided short screws. Two sizes of T-rail connectors are included in the mounting hardware kit: 15/16in (2.38cm) and 9/16in (1.43cm). If extra space is required to accommodate drop ceiling tiles, use the provided spacers and long screws.
PAGE 5
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3.