User's Manual

ManualsBrandsSenao International ManualsElectronicsPronto Hotspot Controller

1. About this Document

This documents describes step-by-step procedure to be followed to install

the Hotspot Controller at your location as quickly as possible and enjoy

the wireless access to Internet and/or to your local network.

2. WISP Information Sheet

This attached document is an information sheet regarding your controller.

The most important thing to note is the Wisp Admin login and password

that is unique to your WISP. These login credentials will allow you to

now access the Pronto OSS/BSS interface. To login to the OSS/BSS

interface, you will need to do the following:

Step1: Open a browser and navigate to https://oss.prontonetworks.com

Step2: In the field labeled “Select an Environment,” select in the pull-

down menu “Standalone”

Step3: In the field labeled “WISP ID,” enter your WISP ID Number

located on the information sheet.

Step4: In the field labeled “Login ID,” enter your login ID located on the

information sheet. This login ID will be case sensitive.

Step5: In the field labeled “Password,” enter your password located on

the information sheet. This password will be case sensitive.

The WISP Information Sheet additionally includes information such as

your WISP name, WISP ID number, location name, franchise name,

controller MAC ID, Guest Accounts, SSID, walled garden sites, and

configurations for the WAN and LAN ports. This information is specific

for that controller and these configurations can be modified within the

Summary of content (8 pages)

PAGE 1
. About this Document This documents describes step-by-step procedure to be followed to install the Hotspot Controller at your location as quickly as possible and enjoy the wireless access to Internet and/or to your local network. 2. WISP Information Sheet This attached document is an information sheet regarding your controller. The most important thing to note is the Wisp Admin login and password that is unique to your WISP.
PAGE 2
OSS/BSS interface. If you have any questions or concerns about reconfiguring the controller, please contact your Account Manager or you can access and download an OSS/BSS guide along with several step-bystep documents via the Wisp Information Website located at http://wispinfo.prontonetworks.com/. Please contact your account manager to request credentials to access this website. 3. Installation Procedure for Hotspot Controller Follow these easy steps to install the Hotspot Controller.
PAGE 3
Step3: Plug one end of the DC Adaptor into the slot provided at the rear of the Hotspot Controller and other end into an electrical outlet. Step 4: Turn ON the Power of your electrical outlet. The Hotspot Controller will obtain the required configuration and start initialize by itself. This process will take approximately 3-5 minutes. 4. Understanding the Booting process This section explains that how the Hotspot Controller is booting up when the Power is turned ON.
PAGE 4
In general, the Hotspot Controller is pre-configured as per the information you provided in “Location_Information_Form” document when ordering Hotspot Controller for this particular location. In that case, the Hotspot Controller is pre-configured according to your DSL/Cable Internet connection type such as DHCP, STATIC IP or PPPoE and shipped to your location.
PAGE 5
In case you don’t have a cross-over cable, use normal RJ-45 Ethernet cable and a hub to connect to LAN port of Hotspot Controller as shown in the diagram (figure-3) below: Step3: Power ON the Hotspot Controller. Check the link activity on LAN port of Hotspot Controller to see your Laptop/PC has link. Note: Your Laptop/PC should be configured as DHCP client to obtain IP address from 192.168.4.0 range from Hotspot Controller.
PAGE 6
Type the following commands as shown below in Bold-Black letters: Pronto CLI: pcli 0.1-0 % WARNING: No environment % Factory password presets configured Please refer to documentation for login information User Access Verification Password: default PCLI> enable Password: default PCLI# configure terminal config# interface eth0 config-if# ip address x.x.x.x y.y.y.y # NOTE: Replace x.x.x.x with your STATIC IP and y.y.y.y with Subnet Mask provided by your ISP config-if# done config# default-router z.z.z.
PAGE 7
• PPPoE information. When the Hotspot Controller comes up ONLINE, then it will download all configurations from Pronto OSS server and boot by itself if the Hotspot Controller in future. If you do not have an Internet connection at this location to reconfigure Hotspot Controller in Pronto OSS, please contact Pronto WISP Support at 1-800-PRONTO-0. We will assist you.
PAGE 8
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.