High-Speed Wireless Cardbus Adapter User’s Manual Version: 1.
Table of Contents 1 INTRODUCTION.................................................................................................................... 4 1.1 FEATURES & BENEFITS..................................................................................................... 4 1.2 PACKAGE CONTENTS ........................................................................................................ 4 1.3 PC CARD DESCRIPTION...................................................................................
1 Introduction The High-Speed Wireless Cardbus Adapter is the most convenient way to let you put a desktop/notebook computer almost anywhere without the hassle of running network cables. Now you don’ t need to suffer from drilling holes and exposed cables. Once you are connected, you can do anything, just like the wired network. The High-Speed Wireless Cardbus Adapter operates seamlessly in 2.4GHz frequency spectrum supporting the 802.11b (11Mbps) and the 802.11g (54Mbps) wireless standards.
. • Access Point: Sold green when wireless is connected. . • OFF: No wireless activity. 1.4 System Requirements The following are the minimum system requirements in order to use the PC card. . • PC/AT compatible computer with a PCMCIA Type II slot. . • Windows 98SE/ME/ /2000/XP operating system. . • 300 MHz or higher processor . • 32 MB or greater memory 1.5 Applications The wireless LAN products are easy to install and highly efficient.
Network managers implement wireless LANs to provide backup for mission-critical applications running on wired networks. h) Training/Educational facilities Training sites at corporations and students at universities use wireless connectivity to ease access to information, information exchanges, and learning. 1.
depicts a network in infrastructure mode. 2 Install Drivers & Client Utility This chapter describes how to install the drivers and client utility in Windows 98/ME/2000/XP. 2.1 Before You Begin Before installing the new drivers into your PC, you need to remove all of the Wireless LAN PC card drivers that you have installed. During the installation, Windows 98SE/ME/2000/XP may need to copy systems files from its installation CD.
folder, or click on the Next button to use the default folder. 4. The Install Wizard will then allow you to select a Program Folder. Select one from the list, or click on the Next button to use the default program folder. 5. The Install Wizard will then inform you that it has enough information to begin the installation process. Click on the Next button to continue. 6. The Install Wizard will then begin to copy the files to your computer, as the image depicts below. 7. Click on the Finish button.
11. The installation of the PC card is now complete. Click on the Finish button. 3 Using the Client Utility This chapter describes the features of the PC card and its configuration process. After a successful installation, an IEEE 802.11 program group will be added to the Programs menu. To launch the Client Utility click Start > Programs > IEEE 80211 > 802.11 WLAN NIC Utility. You will then see the Client Utility icon in the system tray of you computer.
Network Type, Current Mode, Current Channel, Link Status, Encryption Type, and IP Address. Configuration for each of these items is described in their respective sections. 3.1.1 Advanced Status Click on the Advanced button to view more details about the status. You will then see the following window.
The Advanced Status window displays the following: Country, Transmit Power Level, Network Name (SSID), Power Save Mode, Frequency, Transmit Rate, and Receive Rate. Configuration for each of these items is described in their respective sections. Click on the OK button to close this window and return to the Current Status tab. 3.2 Profile Management The second tab displayed in the Profile Management tab.
3.2.1 Available Networks Click on the Available Networks… button to select from a list of Access Point and Ad Hoc networks. You will then see the following window.
This window displays a list of Access Point and Ad-Hoc networks in the area. Details included are the Network Name (SSID), Encryption Key, Signal Strength, Channel, and Wireless Mode. If you would like to associate with an Access Point or Ad-Hoc network, select a Network Name (SSID) from the list and then click on Activate button. You will then be associated with that network, if you have the correct permissions/keys. 3.2.
a. Profile Name: enter a name for this profile; this can be any name that you may associate with your network. b. SSID1: enter the SSID of the network. The SSID is a unique name shared among all points in your wireless network. The SSID must be identical for all points in the network, and is case-sensitive. c. Click on the OK button to save the changes. 3.2.2.2 Security The second tab displayed is the Security tab. Here you can specify and configure the security method that is used by your network.
3.2.2.2.1 None If your network does not use any type of security select the None radio button and then click on the OK button. 3.2.2.2.2 WPA & 802.1x WPA (Wi-Fi Protected Access) was designed to improve upon the security features of WEP (Wired Equivalent Privacy). The technology is designed to work with existing Wi-FI products that have been enabled with WEP.
3.2.2.2.2.1 WPA & 802.1x/TLS EAP (Extensible Authentication Protocol) is an extension to the PPP protocol that enables a variety of authentication protocols to be used. It passes through the exchange of authentication messages, allowing the authentication software stored in a server to interact with its counterpart in the client.
To enable EAP-TTLS security: 1. To use EAP-TTLS security, the machine must already have the EAP -TTLS certificates downloaded onto it. Check with the IT manager. EAP security uses a dynamic session-based WEP key from the USB device and RADIUS server for encryption, and a client certificate for authentication. 2. If EAP-TTLS is supported, choose EAP-TTLS from the drop-down menu on the right, and then click the Configure button.
3.2.2.2.2.2 WPA & 802.1x – PEAP EAP (Extensible Authentication Protocol) is an extension to the PPP protocol that enables a variety of authentication protocols to be used. It passes through the exchange of authentication messages, allowing the authentication software stored in a server to interact with its counterpart in the client.
To enable PEAP (EAP-GTC) security: 1. To use PEAP (EAP-GTC) security, the server must have PEAP certificates, and the server properties must already be set. Check with the IT manager. 2. If PEAP is supported, choose PEAP from the drop-down menu on the right, and then click the Configure button. To enable WPA & 802.1x_LEAP security: 1. LEAP security requires that all infrastructure devices are configured for LEAP authentication. Check with the IT manager.
2. If supported, choose LEAP from the drop-down menu on the right, then click the Configure button. 3.2.2.2.3 WPA – PSK WPA – PSK (Pre-shared Key) is used in a Pre Shared Key mode that does not require an authentication server. Access to the Internet and the rest of the wireless network services is allowed only if the pre-shared key of the computer matches that of the Access Point. This approach offers the simplicity of the WEP key, but uses stronger TKIP encryption.
Enter the WPA pass-phrase in the text box. The pass-phrase must be a minimum of 8 characters. This is the password shared between the Access Points and the Clients. Click on the OK button when completed. 3.2.2.2.5 Pre-Shared Key Pre-shared Key does not require an authentication server. Access to the Internet and the rest of the wireless network services is allowed only if the pre-shared key of the computer matches that of the Access Point.
3.2.2.3 Advanced The third tab displayed is the Advanced tab. Here you can configure details about an Access Point or Ad Hoc network Configuration for each security method is described below. 3.2.2.3.
Power Save Mode: select a power save mode from the drop-down list. Network Type: select Access Point from the drop-down list. 802.11b Preamble: select Short & Long or Long Only. Transmit Power Level: select a power level from the drop-down list. Wireless Mode 2.4 GHz 11 Mbps: place a check in this box if you would like to use 2.4GHz 11 Mbps. Wireless Mode: place a check in this box if you would like to use the available frequencies. Click on the OK button to continue. 3.2.2.3.
3.3.1 Advanced Statistics Click on the Advanced Statistics button to view more detailed statistics.
3.3.2 Driver Information Click on the Driver Information button to view details about the driver. Included information is: Card Name, MAC Address, Driver, Driver Version, and Driver Date.
4. Un-installation If the PC card installation is unsuccessful for any reason, the best way to solve the problem may be to completely uninstall the PC card and its software and repeat the installation procedure again. Follow the steps below in order to uninstall the Client Utility: 1. Click on Start > Settings > Control Panel. 2. Double click on the System icon. 3. Click on the Hardware tab, and then click on the Device Manger button. 4.
Appendix A - Specifications
1. General Radio Data Rate (Auto-rate capable) Network Standards Security Network Architecture Drivers Access Protocol Roaming Operating Voltage Regulation Certifications LED Indicator 802.11g : 6, 9, 12, 18, 24, 36, 48 & 54Mbps 802.11b : 1, 2, 5.5, 11Mbps WECA (Wi-Fi & Wi-Fi5 Compliant), IEEE802.11, IEEE802.11g draft, IEEE802.11b, draft IEEE802.11e, f, h and I standards, IEEE802.11x (Optional) IEEE802.
Temperature Range Humidity (non-condensing) -10℃ to 55℃ – Operating -40℃ to 70℃ – Storage 5% to 95% Typical 4. Physical Specifications Interface Antenna Dimensions 32-bit CardBus PC Card Standard V7.1 Type II Integrated built-in diversity Antenna 118(L)mm * 54(W)mm * 6.3(H)mm (4.65in * 2.13in * 0.30in) Appendix B – FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A. Highest SAR test Value: 1.280 W / kg this device is only approved for laptop configurations utilizing side mounted PCMCIA Card slots.
