User Manual

USER’S GUIDE
Precautions
• Please read and follow these instructions and keep this manual in a
safe place.
• Clean this product with only a soft, dry cloth.
• Keep this product away from children.
• Make sure that this product is intact and that there are no missing
parts.
• To avoid damage to this product, be careful not to overtighten or
improperly thread any of the threaded fittings.
• Do not exceed the maximum load capacity.
• All photos are for illustrative purposes only.
Contents Include
• Wall plate
• Two (2) vertical mounting brackets
• Horizontal mounting bracket
• Removable mounting bracket
• 4 Removable mounting plates
• Mounting-plate bolt
• Two (2) Mounting-plate nuts
• Two (2) 6 × 40 mm mounting screws
• Two (2) 6 × 60 mm mounting screws
• 8 mm screw
• Two (2) 3/8" screw anchors
• Two (2) 4 × 12 mm machine screws
• Two (2) 5 × 12 mm machine screws
• Two (2) 6 × 12 mm machine screws
• 5 mm hex key
Vertical Mounting
1. Start with the wall plate on a flat
surface. Orient the mounting
plate’s bolt-head so it's facing you.
2. Place one of the vertical
mounting brackets onto the
right-hand side of the wall plate
so their bolt holes are aligned.
Hold the mounting bracket in
place with the nut that has a
small bolt-hole.
Tip: The shape of the nut will
conform to the
corresponding side of the
wall plate.
3. Place the other vertical mounting bracket on the left-side of the wall
plate. Hold the mounting bracket in place with the nut that has a large
bolt-hole.
4. Insert the mounting-plate bolt through the nut that has a large
bolt-hole and use the included hex key to screw the bolt in place until
secure.
5. Confirm the desired mounting location on your wall. Hold the wall
plate against the wall at the desired mounting location, and use a
pencil to mark the exact location of the mounting holes.
6. Use a drill with a 1/4" bit to drill holes through the pencil marks.
7. Fully insert the included screw anchors into the holes.
8. Position the wall plate with the swivel-action bolt-head facing up.
Align the mounting holes with the screw anchors, and use the
6 × 40 mm or 6 × 60 mm mounting screws to secure the wall plate
to the anchors.
Note: Use the 6 × 40 mm screws for the ASM-3 and ASM-4 speakers.
Use the 6 × 60 mm screws for the ASM-5 and ASM-6 speakers.
9. Align the slots in the vertical mounting brackets with the mounting
holes in the speaker. Use the machine screws to secure the speaker to
the mounting bracket assembly. Use the 4 × 12 mm screws for the
ASM-3, the 5 × 12 mm screws for the ASM-4, and the 6 × 12 mm
screws for the ASM-5 and ASM-6.
Horizontal Mounting
Note: When mounting a pair of speakers horizontally, make sure to
position the tweeters on the outside in order to achieve proper stereo
imaging.
1. Start with the mounting plate on a
flat surface, with the mounting
plate’s bolt-head facing you.
2. Place the horizontal mounting bracket
onto the mounting plate so their bolt
holes are aligned.
3. Place the nut that has a small bolt-hole on
the right-hand side of the wall plate, and
the nut that has a large bolt-hole on the
left-hand side of the wall plate, and hole
them in place.
Tip: The shape of the nut will
conform to the corresponding
side of the wall plate.
4. Insert the mounting-plate bolt through the nut that has a
large bolt-hole and use the included hex key to screw the bolt in
place until secure.
5. Confirm the desired mounting location on your wall. Hold the wall
plate against the wall at the desired mounting location, and use a
pencil to mark the exact location of the mounting holes.
6. Use a drill with a 1/4" bit to drill holes through the pencil marks.
7. Fully insert the included screw anchors into the holes.
8. Position the wall plate with the swivel-action bolt-head facing up.
Align the mounting holes with the screw anchors and use the 6 × 40
mm or 6 × 60 mm mounting screws to secure the wall plate to the
anchors.
Note: Use the 6 × 40 mm screws for the ASM-3 and ASM-4 speakers.
Use the 6 × 60 mm screws for the ASM-5 speakers.
9. Align the horizontal mounting brackets with the mounting holes in
the speaker, and use the machine screws to secure the brackets to
your speaker. Use the 4 × 12 mm screws for the ASM-3, the 5 × 12 mm
screws for the ASM-4, and the 6 × 12 mm screws for the ASM-5 and
ASM-6.
Removable Mounting
1. Start with the mounting plate on a flat
surface. Orient the mounting plate’s
bolt-head so it's facing you.
2. Place the removable mounting bracket
onto the mounting plate so their bolt holes
are aligned. Make sure the removable
mounting bracket is positioned so that
when you hold the assembly with the
swivel-action bolt-head facing up, the
bracket’s hook is also facing up, as it will
need to support your speaker. When
the hook is facing up, the screw
hole will be below the hook.
3. Place the nut that has a small
bolt-hole on the right-hand
side of the wall plate, and the nut that has a large bolt-hole on the
left-hand side of the wall plate, and hold them in place.
Tip: The shape of the nut will conform to the corresponding side of
the wall plate.
4. Insert the mounting-plate bolt through the nut that has a large
bolt-hole, and use the included hex key to screw the bolt in place until
secure.
5. Confirm the desired mounting location on your wall. Hold the wall
plate against the wall at the desired mounting location, and use a
pencil to mark the exact location of the mounting holes.
6. Use a drill with a 1/4" bit to drill holes through the pencil marks.
7. Fully insert the included screw anchors into the holes.
8. Position the wall plate with the swivel-action bolt-head facing up.
Align the mounting holes with the screw anchors and use the 6 × 40
mm mounting screws to secure the wall plate to the anchors.
9. Detemine which of removable mounting plates fits your speaker by
aligning its mounting holes with the mounting holes in your speaker.
They should line up perfectly. The mounting plate should be flush
against the back of your speaker.
10. Use the provided machine screws to
secure the removable mounting
plate to your speaker.
Note: Use the 4 × 12 mm
machine screws for the
ASM-3 speaker. Use the
5 × 12 mm machine
screws for the ASM-4 and
ASM-5 speakers. Use the 6 × 12
mm machine screws for the ASM-6 speaker.
11. Lift the speaker and carefully mount it onto the
removable mounting bracket’s hook via the removable
mounting plate.
To permanently fix your speaker to this mount, first attach the removable
mounting plate to the removable mounting bracket and secure it with
the included 4 × 8 mm screw. Then mount your speaker to the removable
mounting plate with your machine screws.
ASM-MNTKIT
Mounting the ASM-6
1. The ASM-6 requires two horizontal mounts per speaker so you'll need
two of these kits for each one. Follow steps 1 through 4 of the
Horizontal Mounting instructions to assemble the horizontal mounts.
2. The horizontal mounts fit vertically onto the ASM-6, one on each side
of the speaker. Confirm the desired mounting location on your wall
and measure two spots 4" (10.2 cm) apart, one for each horizontal
mount.
3. At each mounting location, hold the wall plate against the wall, and
use a pencil to mark the exact location of the mounting holes.
4. Use a drill with a 1/4" bit to drill
holes through the pencil marks.
5. Fully insert the included screw
anchors into the holes.
6. Position the wall plates with
the swivel-action bolt-heads
facing up. Align the mounting
holes with the screw anchors
and use the 6 × 60 mm
mounting screws to secure
the wall plates to the anchors.
7. Align the horizontal mounting
brackets with the mounting
holes in the speaker and use
the 6 × 12 mm machine screws
to secure the brackets to your
speaker.
Tilting and Swiveling the Speaker
To adjust the vertical angle of the speaker, use the included hex key to
slightly loosen the horizontal mounting bolt. Tilt the speaker as desired
and retighten the bolt until secure.
To adjust the horizontal angle of the speaker, use the included hex key to
slightly loosen the vertical mounting bolt. Swivel the speaker as desired
and retighten the bolt until secure.
Important!
Always exercise caution when tilting and swiveling your speakers. Make
sure to keep one hand on the speaker to hold it steady.
Note: The ASM-6 can be adjusted only vertically.
Specifications
One-Year Limited Warranty
Senal provides a limited warranty to the original purchaser that this
product is free from defects in materials and workmanship under normal
consumer use for a period of one (1) year from the original purchase date
or thirty (30) days after replacement, whichever occurs later. Senal’s
responsibility with respect to this limited warranty shall be limited solely
to repair or replacement, at Senal’s discretion, of any product that fails
during normal consumer use. Inoperability of the product or part(s) shall
be determined by Senal. If the product has been discontinued, we
reserve the right to replace it with a model of equivalent quality and
function.
To obtain warranty coverage, contact Senal to obtain a return
merchandise authorization (“RMA”) number, and return the defective
product to Senal, along with the RMA number and proof of purchase.
Shipment of the defective product is at the purchaser’s own risk.
This warranty does not cover damage or defect caused by misuse,
neglect, accident, alteration, abuse, improper installation or maintenance.
EXCEPT AS PROVIDED HEREIN, SENAL MAKES NEITHER ANY EXPRESS
WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you
with specific legal rights, and you may also have additional rights that
vary from state to state.
© Copyright 2014 Gradus Group