www.sena.
SPH10S © 1998-2014 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH5™, SPH10™, SPH10S™, SPH10H™, EXPAND™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena.
SPH10S 1. INTRODUCTION..................................................................5 2. PACKAGE CONTENTS.......................................................6 3. INSTALLING THE SPH10S ON YOUR HELMET................7 4. POWERING ON/OFF AND CHARGING..............................8 4.1 4.2 4.3 4.4 4.5 Powering On................................................................................8 Powering Off................................................................................8 Charging.........
SPH10S 20. RESET TO FACTORY DEFAULT SETTINGS...................32 21. FAULT RESET...................................................................32 22. FIRMWARE UPGRADE.....................................................33 23. CASE STUDY....................................................................34 Case 1 Case 2 ...........................................................................................34 ...........................................................................................
SPH10S Thank you for choosing the Sena SPH10S, Bluetooth ® Headset & Intercom designed for snow sports helmets. With the SPH10S, you can call handsfree on your Bluetooth mobile phone, listen to stereo music and have intercom conversations in full duplex with other SPH10S users. The SPH10S is compliant with the Bluetooth 3.0 supporting the following profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio Distribution Profile (A2DP), and Audio Video Remote Control Profile (AVRCP).
SPH10S 2.
SPH10S • Stereo Audio Cable 3. INSTALLING THE SPH10S ON YOUR HELMET English • USB Power and Data Cable 1. Remove the original ear flaps of your helmet and insert the plastic plate of SPH10S into where the ear flaps are removed in the helmet. 2. Please make sure that one of headset ear flaps with the microphone is located to the left side of your helmet. 3. Put the wire connected with ear flaps into the rear part of you helmet.
SPH10S 4. POWERING ON/OFF AND CHARGING To power on and off the headset, you don’t need to press and hold any button for several seconds. Just short press the Jog Dial and the Phone Button simultaneously, and you will get quick on-and-off convenience. 4.1 Powering On Press the Jog Dial and the Phone Button at the same time for about 1 second to power on. The blue LED turns on and you will hear ascending beeps. 4.
SPH10S You can easily adjust the volume by rotating the Jog Dial. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music. So you can always maintain the preferred optimum volume level for each audio source. 6.
SPH10S 2. Search for Bluetooth devices on your mobile phone. Select the Sena SPH10S in the list of the devices detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phone may not ask for the PIN. 4. The mobile phone confirms that pairing has completed and the SPH10S is ready to use. You will hear a voice prompt from the SPH10S saying “Your headset is paired”. 5. If the pairing process is not completed within three minutes, the SPH10S will return to stand-by mode. 6.
SPH10S 6.3 Bluetooth Stereo Device Pairing Note: 1. I f Bluetooth connection between the headset and a mobile phone is disconnected, tap the Phone Button to recover the Bluetooth connection immediately. 2. I f Bluetooth connection between the headset and a media player is disconnected, press the Jog Dial for 1 second to recover the Bluetooth connection and play. 7.
SPH10S and you hear multiple beeps. 2. Within 2 seconds, tap the Jog Dial again, then the LED turns to red flashing and the beeps turn to double mid-tone beeps. You will hear a voice prompt saying “Media selective pairing”. 3. Search for Bluetooth devices on your smartphone. Select the Sena SPH10S in the list of devices detected on your phone. 4. Enter 0000 for the PIN. Some smartphones may not ask for PIN. 7.2 HFP for Phone Call Only 1.
SPH10S B D C Note: Pairing A & B 4. Y ou can make other pairings between the headset A and C, and between the headset A and D by following the same procedure as above. A B A D C Pairing A & C B D C Pairing A & D For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset A. 8.
SPH10S 9. SPH10S CONFIGURATION SETTING You can set the configuration of the SPH10S by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the Jog Dial for 12 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt saying “Configuration menu”. 2. Rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus. You will hear voice prompts for each menu items as below. 3.
SPH10S Note: 1. A fter assigning a phone number to one of three speed dials, you can continually assign another phone number to the rest of two speed dials. 2. Y ou can assign phone numbers to speed dials in your PC. Please visit the Sena Bluetooth web site at www. sena.com for more information. 9.2 Enabling/Disabling Voice Activated Phone Answering Voice Prompt “VOX phone” Factory Default Enable Enable Tap the Phone Button Disable Tap the Jog Dial English 3.
SPH10S by speaking any word loudly enough. The most effortless way to trigger intercom VOX is to blow into the microphone as if blowing dust off the microphone. If you start an intercom conversation by VOX, the intercom terminates automatically when you and your intercom friend remain silent for 20 seconds. However, if you manually start an intercom conversation by tapping the Jog Dial, you have to terminate the intercom conversation manually.
SPH10S 9.6 Delete All Bluetooth Pairing Information Tap Phone Button “Delete all pairings” Speed Dial Execute N/A Factory Default N/A VOX Phone Enable Disable Execute Tap the Phone Button VOX Intercom Enable Disable Voice Prompt Enable Disable Sidetone Enable Disable To delete all Bluetooth pairing information of the SPH10S, rotate the Jog Dial until you hear a voice prompt saying “Delete all pairings”, and tap the Phone Button to confirm.
SPH10S 10. FUNCTION PRIORITY The SPH10S operates in the following order of priority: (highest) Mobile phone, Intercom, Stereo music by audio cable, Music sharing by Bluetooth stereo music, (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and intercom conversation is interrupted by incoming mobile phone call. 11.
SPH10S 3. To track forward or track back, rotate while pressing the Jog Dial clockwise or counter clockwise. Note: 2. To play or pause music, press and hold the Jog Dial for 1 second until you hear a double beep. Bluetooth music is available only when the MP3 jack port remains open. Please make sure the audio cable is unplugged from the clamp unit to play music by Bluetooth.
SPH10S 12. MOBILE PHONE CALL MAKING AND ANSWERING 12.1 Mobile Phone Call Making and Answering 1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call. 2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering is enabled. 3. To end a call, tap the Phone Button or press the Jog Dial for 2 seconds until you hear a beep, or wait for the called person to end the call. 4.
SPH10S (1) Last number redial (4) Speed dial 3 (2) Speed dial 1 (5) Cancel (3) Speed dial 2 4. After selecting the last number redial menu, you will hear a voice prompt saying “Last number redial”. Then, to redial the last phone call number, tap the Phone Button or the Jog Dial. 5. To call one of the speed dials, rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus until you hear a voice prompt saying “Speed dial (#)”. Then, tap the Phone Button or the Jog Dial. 6.
SPH10S 13. TWO-WAY INTERCOM 13.1 Start and End Two-way Intercom 1. You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: single tapping to intercom with the first intercom friend, double tapping with the second intercom friend, and triple tapping with the third intercom friend. 1st Intercom Friend 2nd Intercom Friend 2. To terminate an intercom conversation, single tap the Jog Dial.
SPH10S 14. THREE-WAY CONFERENCE INTERCOM English a. To answer the phone call and stop the intercom conversation, tap the Jog Dial or the Phone Button. When you hang up the phone call, the intercom will automatically be recovered. b. To reject the phone call and stay on the intercom conversation, press the Jog Dial for 2 seconds until you hear a beep. U nlike other Bluetooth headsets, this prevents a user from being dropped out of an intercom conversation by an incoming mobile call. 2.
SPH10S Pa i (A) First Friend (B) Second Friend (C) 2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). 24 (A) First Friend (B) Second Friend (C) Second Friend (C) 4. Now you (A) and two SPH10S intercom friends (B & C) are having a three-way conference intercom. (A) First Friend (B) (A) First Friend (B) 3.
SPH10S 14.2 End Three-way Intercom Jog Dial Operation Press for 1” 15. FOUR-WAY CONFERENCE INTERCOM 15.1 Start Four-way Intercom You can have four-way conference intercom with three other SPH10S users by adding one more intercom participant to the three-way intercom. While you are having three-way intercom as above in section 14.1, a new participant (D), who is an intercom friend of your intercom friend (C), may join the conference intercom by making an intercom call to your intercom friend (C).
SPH10S 15.2 End Four-way Intercom As same in the case of three-way intercom, you can completely get out of the four-way conference intercom or just disconnect a single intercom connection. 1. Press the Jog Dial for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B) and (C). 2. Tap or double tap the Jog Dial to disconnect the intercom connection with one of the two intercom friends accordingly.
SPH10S g rin (B) (A) i Pa Non-Sena Bluetooth headsets may initiate the Universal Intercom connection, activating the voice dialing or using the redialing operation. You may also disconnect the existing connection by ending a call operation function (refer to the users’ manual of the headsets for voice dialing, redialing, and ending a call). 1. You (A) need to be paired with non-Sena Bluetooth headset (B) and another SPH10S headset (C) for the three-way conference intercom.
SPH10S 2. Start an intercom conversation with non-Sena Bluetooth headset (B) in your intercom group. For example, you (A) may start an intercom conversation with non-Sena Bluetooth headset (B). The non-Sena Bluetooth headset (B) may also start an intercom call with you (A). (A) (B) (C) (A) 28 (A) (B) 3. The other SPH10S (C) may join the intercom by making an intercom call to you (A). (B) 4.
SPH10S 16.4 Four-way Universal Intercom You may have a couple of other four-way Universal Intercom configurations, 1) your headset (A), a non-Sena Bluetooth headset (B), another SPH10S (C), and a non-Sena Bluetooth headset (D), 2) your headset (A), a non-Sena Bluetooth headset (B), and two other SPH10S headsets (C and D). You may make the four-way Universal Intercom call the same way as a normal four-way intercom call. 16.4.
SPH10S 4. Now two SPH10S headsets (A & C) and two nonSena Bluetooth headsets (B & D) are connected with the four-way Universal Intercom. (A) (C) (D) (B) You may disconnect a four-way Universal Intercom using the same way as you do in a normal four-way intercom. Please refer to section, 15.2 “End Four-way Intercom”. 16.4.2 Four-way Universal Intercom Case 2 Three SPH10S headsets (A, C and D) and one nonSena Bluetooth headset (B). The procedure is the same as the case 1 described in section 16.4.1.
SPH10S When you try to start an intercom conversation with an intercom friend who is already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later. 19. INTERCOM RECONNECTION English 18. INTERCOM FAILURE If your intercom friend goes out of range while having an intercom conversation, you may hear static noise and eventually the intercom will be disconnected.
SPH10S 20. RESET TO FACTORY DEFAULT SETTINGS 1. To restore the SPH10S to factory default settings, press and hold the Phone Button for 12 seconds until the LED shows solid red and you hear double beeps. You will hear a voice prompt saying “Factory reset”. 2. Within 5 seconds, press the Jog Dial to confirm reset. The headset will be restored to factory setting and switched off automatically. You will hear a voice prompt saying “Headset reset, good-bye”. 3.
SPH10S 22. FIRMWARE UPGRADE English 3. Take out the module from the front of the ear flap to see the reset pin-hole on the opposite side of the module. The SPH10S supports firmware upgrade function. Please visit Sena Bluetooth web site at www.sena. com to check the latest software downloads. 4. Insert a paper clip into the reset pin-hole and press the reset button for 1 second with light pressure, at which time the SPH10S will be switched off. Turn the SPH10S back on.
SPH10S Case 2 23. CASE STUDY Case 1 • iPhone for mobile phone call and stereo music streaming •SPH10S for two-way intercom •Feature phone for mobile phone call •iPod Touch for stereo music streaming • Two other SPH10Ss for three-way conference intercom Feature Phone Mobile Pairing: 6.1 Call iPhone Mobile Call Pairing: 6.1 Music SPH10S Intercom Conversation SPH10S Pairing: 8.1 Intercom Conversation SPH10S Pairing: 8.1 Music SPH10S Intercom Conversation Pairing: 8.1 SPH10S 34 Pairing: 6.
SPH10S Button Phone Button + Jog Dial Description Duration LED Beep Power-on 1 sec Solid blue Ascending beeps Power-off Tapping Solid red Descending beeps Mobile phone pairing 5 sec Blue & red alternatively flashing High tone multiple beeps MP3 pairing 5 sec Blue & red alternatively flashing High tone multiple beeps Call transfer 2 sec - High tone single beep 12 sec Solid red High tone double beeps Phone Button Factory reset Jog Dial within 5 sec to confirm reset English 24.
SPH10S CERTIFICATION AND SAFETY APPROVALS FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
SPH10S WEEE (Waste Electrical and Electronic Equipment) The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
SPH10S SAFETY INFORMATION Please ensure that the product is properly used by observing the warnings and cautions below to prevent any risk and/or damage to property. Product Storage and Management • Keep the product free of dust. It may damage mechanical and electronic parts of the product. • Do not store the product in high temperatures as this may reduce the life span of electronic devices, damage the battery, and/or melt plastic parts of the product. • Do not store the product in cold temperatures.
SPH10S Battery This product has an irreplaceable rechargeable battery inside. Therefore, when using the product, make sure to adhere to the following: • In recharging the battery, make sure to use an approved charger provided by the manufacturer. Use of a non-approved charger may cause fire, explosion, leakage, and other hazards may also reduce the life time or performance of the battery. • Store the battery at temperatures of 15°C~25°C (59°F~77°F).
SPH10S PRODUCT WARRANTY AND DISCLAIMER Limited Warranty Limited Warranty Sena Technologies, Inc. (“Sena”) guarantees the product quality based on the technical specification stated in the product manual, and data regarding product warranty. Here, product warranty extends to the product only. Sena will not be liable for any loss, damage of human life, or loss of property which may result from using the product beyond defective parts or flaws that occur due to problems in manufacture.
SPH10S • Risk factors, which may occur when you use the product, may be due to errors of the manufacturer, its agents, or third parties which are involved in the manufacturing. • Risk factors, which may occur when you use the product, may be unforeseeable. Therefore, you must take full responsibility for any damage or loss caused by all risk factors which may occur when using the product. • When you use the product, use good judgment; never use it under the influence of alcohol. 6.
SPH10S Further, Sena will not be liable for any substantial damage not related to the, condition, environment, or malfunction of the product. All risks related with the operation of the product depend entirely on the user regardless of its use by the initial purchaser of a third party. AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. IN ANY CASE, THE TOTAL COMPENSATION LIABILITIES OF SENA OR ITS SALES AGENTS SHALL NOT EXCEED THE PRICE PAID FOR THE PRODUCT BY THE PURCHASER.
SPH10S Warranty Service To obtain product warranty service, send the defective product, at your expense, to the manufacturer or the seller along with proof of purchase (a receipt that shows the purchase date, a product registration certificate of the Website, and other relevant information). Take necessary measures to protect the product. In order to get a refund or replacement, you must include the whole package as it was purchased.
2.1.0 www.sena.com User's Guide for Firmware v5.