SMH10R Low Profile Motorcycle Bluetooth® Headset & Intercom 900m Intercom 980yds Ultra Slim & Feather Light www.SenaBluetooth.
SMH10R © 1998-2013 Sena Technologies Inc. All rights reserved. Sena Technologies Inc. reserves the right to make any changes and improvements to its product without prior notice. Sena™ is a trademark of Sena Technologies Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH10R™, SMH5™, SMH5-FM™, SPH10™, SPH10H™, SPH10H-FM™, SPH10S™, SR10™, SR10i™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena.
SMH10R 1. 2. 3. 4. INTRODUCTION................................................................................................................4 PACKAGE CONTENTS......................................................................................................5 INSTALLING THE SMH10R ON YOUR HELMET. . ...............................................................6 POWERING ON/OFF AND CHARGING.. .............................................................................8 4.1 4.2 4.3 4.4 4.
SMH10R 1. INTRODUCTION Thank you for choosing the Sena SMH10R, Low Profile Bluetooth Stereo Headset and Intercom. With the SMH10R, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions from your GPS navigation system by wireless Bluetooth, and have intercom conversations in full duplex with a passenger or other motorcycle riders. The SMH10R is compliant with Bluetooth 3.
SMH10R 2.
SMH10R • Velcro Pads for Main Unit • Double Sided Adhesive Tapes for Main Unit • Microphone Sponges 3. INSTALLING THE SMH10R ON YOUR HELMET To securely install the main unit of the SMH10R, you can use the velcro pad or double sided adhesive tape. Please follow the procedure below. 1. Peel off the cover of the adhesive tape of the velcro pad and attach it on the back plate of the main unit.
SMH10R 4. Attach the main unit to the velcro pad of your helmet. English 5. Place the helmet speakers with the velcro pads, centered to your ear, in the ear pockets of the helmet. If the helmet has deep ear pockets, you can use the speaker pads to place the speakers closer to your ears. Attach the speaker connector to the 4 pin connector of the main unit cable. it is positioned close to your mouth when you are wearing the helmet.
SMH10R 7. Attach the velcro pads to the battery pack in the same manner as the main unit and place the battery on the back side of your helmet. Attach the battery connector to the 2 pin connector of the main unit cable. 4. POWERING ON/OFF AND CHARGING 4.1 Powering On Press the Center Button and the (+) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 4.
SMH10R 4.4 Low Battery Warning When the battery is low, the blinking blue LED in stand-by mode turns to red and you will hear mid tone triple beeps and a voice prompt, “Low battery”. English You can charge the SMH10R on a helmet by connecting the supplied USB power & data cable or cigarette charger. You can use any standard micro-USB cable to charge the SMH10R. 4.5 Checking the Battery Level You can check the battery level in two different ways when the headset is powering on.
SMH10R 5. VOLUME ADJUSTMENT You can easily adjust the volume by tapping the (+) Button or the (-) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn the headset off and on. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music.
SMH10R 6.
SMH10R the (-) Button until you hear the voice prompt, “Phone selective pairing”. Please refer to section 8 for more details on phone selective pairing. If you tap the (+) or (-) Button, you can exit from the phone selective pairing mode. 6.4 Media Selective Pairing Voice Prompt “Media selective pairing” Factory Default N/A To go into media selective pairing mode, tap the (+) Button or the (-) Button until you hear the voice prompt, “Media selective pairing”.
SMH10R 6.8 Enabling/Disabling Voice Prompts 6.9 Delete All Bluetooth Pairing Information Voice Prompt “Delete all pairings” Factory Default N/A Enable / Disable Tap the Center Button To delete all Bluetooth pairing information on the SMH10R, tap the (+) Button or the (-) Button until you hear the voice prompt, “Delete all pairings”. Tap the Center Button to confirm. 6.
SMH10R 6.11 Exit Voice Configuration Menu Tap (+) Button or (-) Button Tap Center Button Voice Prompt “Exit configuration” Phone Pairing None Factory Default N/A Multipoint Pairing None Execute Tap the Center Button Phone Selective Pairing None Media Selective Pairing None To exit voice configuration menu and get back to stand-by mode, tap the (+) Button or (-) Button until you hear the voice prompt, “Exit configuration”. Tap the Center Button to confirm.
SMH10R Before using the SMH10R Bluetooth headset with any Bluetooth device for the first time, you need to do the pairing operation. It can be paired with Bluetooth mobile phones, Bluetooth stereo devices such as MP3, or motorcycle specific Bluetooth GPS, and with a Bluetooth adapter or transmitter such as Sena SR10 or SM10. This pairing operation is only required once for each Bluetooth device.
SMH10R 3. If you want to pair a second mobile phone, search for the Bluetooth device on your mobile phone, and select Sena SMH10R in the list of devices detected on the mobile phone. 4. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN. 5. T he mobile phone confirms that pairing has completed and the SMH10R is ready to use. You will hear the voice prompt, “Your headset is paired”. 6.
SMH10R The pairing diagram for multipoint GPS pairing is shown in the figure below. Smart Phone HFP + Mobile Phone Pairing A2DP HFP SMH10R Multipoint Pairing GPS Multipoint GPS Pairing 17 English below to pair the GPS using multipoint pairing. 1. T o enter the voice configuration menu, press and hold the Center Button for 10 seconds until you hear the voice prompt, “Configuration menu”. 2. Tap the (+) Button and you will hear the voice prompt, “Phone pairing”. 3.
SMH10R 7.4.2 GPS Pairing as Mobile Phone If GPS is not only used for turn-by-turn voice instructions but is also your preferred Bluetooth stereo music source, you can pair the GPS to the SMH10R by following the simple procedures in “7.1 Mobile Phone Pairing”. When you do this, the SMH10R thinks the GPS is a mobile phone. But SMH10R can directly pair an additional mobile phone.
SMH10R Smart Phone If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SMH10R for A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SMH10R to their smartphones with only one selective profile: A2DP stereo for music or HFP for phone call. Two-way radio HFP + Mobile Phone Pairing A2DP Wired Connection HFP SMH10R Multipoint Pairing Sena SR10 Wired Connection 8.
SMH10R 2. Triple tap the (+) Button and you will hear the voice prompt, “Phone selective pairing”. 3. Search for Bluetooth devices on your smartphone. Select Sena SMH10R in the list of devices detected on your phone. 4. Enter 0000 for the PIN. Some smart phones may not ask for a PIN. 8.2 Media Selective Pairing: A2DP Stereo Music Only 1. T o enter the voice configuration menu, press and hold the Center Button for 10 seconds until you hear the voice prompt, “Configuration menu”. 2.
SMH10R B D Note: For example, after the pairing procedures listed above, headset D is the first intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset A. C Pairing A & B 4. Y ou can make other pairings between headsets A and C, and between headsets A and D by following the same procedure as above. A B A D C Pairing A & C B D C 9.
SMH10R 10. FUNCTION PRIORITY The SMH10R operates in the following order of priority: (highest) Mobile phone, Intercom, (lowest) Bluetooth stereo music A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by an intercom call, and intercom conversation is interrupted by an incoming mobile phone call. 22 11. STEREO MUSIC You can listen to stereo music from your Bluetooth wireless audio device.
SMH10R 3. To track forward or track back, press the (+) Button or the (-) Button for 1 second until you hear a mid tone single beep. You can stop music streaming while you are listening to the music by pressing the (-) Button for 4 seconds until you hear high tone double beeps. 12. MOBILE PHONE CALL MAKING AND ANSWERING English 2. To play or pause music, press the Center Button for 1 second until you hear a mid-tone double beep. 1.
SMH10R - To redial the last number, press the (+) Button for 3 seconds in stand-by mode. You will hear the voice prompt, “Last number redial”. - To cancel voice dialing or redialing the last number command, tap the Center Button while it is in progress. Answer Tap the Center Button or Say “Hello” End Press the Center Button for 2" Reject Press the Center Button for 2" Call Use phone keypad Redial 13. TWO-WAY INTERCOM 13.1 Start and End Two-way Intercom 1.
SMH10R 13.3 Intercom and Mobile Phone Call End Two-way Intercom Conversation Start intercom End intercom 1st intercom friend 2nd intercom friend 3rd intercom friend Single tap Double tap Triple tap Single tap Start & End Two-way Intercom 13.2 Voice Activated Intercom (VOX Intercom) If VOX Intercom is enabled by the configuration setting as described in section 6.6, you can initiate an intercom conversation with the last connected intercom friend by speaking any word loudly.
SMH10R does not override the mobile phone call because intercom has a lower priority than a mobile call. You have to hang up the mobile phone call to make or receive an intercom call. 13.4 Intercom and GPS If you pair a Bluetooth GPS to the SMH10R as described in 6.3 of this user's guide, you can hear the turn-by-turn voice instructions of the GPS while having an intercom conversation.
SMH10R English 14. THREE-WAY CONFERENCE INTERCOM 14.1 Start Three-way Intercom Smart Phone Two-way radio HFP + Mobile Phone Pairing A2DP Wired Connection Audio from Two-way Radio Multipoint Pairing 1. You (A) need to be paired with two other friends (B & C) for three-way conference intercom.
SMH10R 2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with intercom friend (B). Or intercom friend (B) may start an intercom call with you (A). 4. Now you (A) and two SMH10R intercom friends (B & C) are having a three-way conference intercom. (A) (A) First Friend (B) First Friend (B) Second Friend (C) 3. The second intercom friend (C) may join the intercom by making an intercom call to you (A).
SMH10R Center Button Result Press for 1" Disconnect (B) & (C) Single tap Disconnect (B) Double tap Disconnect (C) 15. FOUR-WAY CONFERENCE INTERCOM English 2. Tap or double tap the Center Button to disconnect intercom connection with one of the two intercom friends accordingly. For example, by single tapping the Center Button, you can terminate the intercom connection with the first intercom friend (B). However, you still have the intercom connection with your second intercom friend (C).
SMH10R 15.2 End Four-way Intercom As in the case of three-way intercom, you can completely exit from the four-way conference intercom or just disconnect a single intercom connection. 1. Press the Center Button for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B) and (C). 2. Tap or double tap the Center Button to disconnect the intercom connection with one of the two intercom friends accordingly.
SMH10R When you try to start an intercom conversation with an intercom friend who is already having a conference intercom with other riders or is on a mobile phone call, you will hear a low tone double beep signifying that the intercom is busy. In this case, you have to try again later. 18. INTERCOM RECONNECTION If your intercom friend goes out of range while having an intercom conversation, you may hear static and eventually the intercom will be disconnected.
SMH10R Case 2 21. CASE STUDY •iPhone for mobile phone calls and stereo music streaming •ZumoTM 660/665 for GPS voice instructions •SMH10R for two-way intercom Case 1 •iPhone for mobile phone calls and stereo music streaming •ZumoTM 550 or ZumoTM 220 for GPS voice instructions •SMH10R for two-way intercom iPhone Mobile Call Pairing: 7.1 Music iPhone Intercom Conversation Mobile Call Pairing: 7.1 Music SMH10R Intercom Conversation SMH10R 32 Pairing: 9.1 GPS Voice SMH10R Pairing: 7.4.
SMH10R Case 4 •iPhone for mobile phone calls via Zumo 660/665 • Zumo 660/665 for GPS voice instructions and stereo music streaming •SMH10R for two-way intercom •Feature phone for mobile phone calls •iPod Touch for stereo music streaming •Two other SMH10R for three-way conference intercom English Case 3 Pairing: Refer to ZumoTM 660/665 manual Mobile Call Feature Phone ZumoTM 660/665 Mobile Pairing: 7.1 Call iPhone Mobile Call Music Pairing: 7.1 GPS Voice Intercom Conversation SMH10R Pairing: 9.
SMH10R Case 5 Case 6 •iPhone for mobile phone calls •iPod Touch for stereo music streaming •TomTom® Rider2 for GPS voice instructions •SMH10R for two-way intercom •iPhone for mobile phone calls and stereo music streaming • Sena SR10 for two-way radio, GPS voice instructions, and radar detector alarm •SMH10R for two-way intercom iPhone iPhone Mobile Pairing: 8.1 Call Intercom Conversation SMH10R Pairing: 9.1 Mobile Call Music Music SMH10R GPS Voice Pairing: 7.
SMH10R MAINTENANCE AND CARE The SMH10R has an external, rechargeable battery. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device. Use of an unapproved charger may present a risk of fire, explosion, leakage, or other hazard. The SHM10R should be treated with care and the following suggestions will help you protect your warranty coverage. 1.
SMH10R DISPOSAL CERTIFICATION AND SAFETY APPROVALS The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection points at the end of their working life. This requirement applies to the European Union and other locations where separate collection systems are available.
SMH10R FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.
SMH10R WAIVER AND GENERAL RELEASE By using the SMH10R you waive all substantial legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all the terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue.
SMH10R conduct of others, including the Company. 5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Two-Year Limited Warranty Sena Technologies, Inc.
SMH10R equipment or software not furnished by Sena. Limited warranty service may be obtained by delivering the Product to Sena or to the international distributor it was purchased through and by providing proof of purchase or receipt date. Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to Sena, and to use the original shipping container or equivalent.
SMH10R English WARNING Sena informs you that using this device in public traffic may not be authorized by the law. Please check your local laws and do not use this device in public traffic, but only on private property or closed circuits. If the simultaneous use of both ear speakers while riding a motorcycle is prohibited by your local law, please use only a single ear speaker while riding. Sena denies any liability should you choose not to respect this warning.
1.0.1 www.SenaBluetooth.com User's Guide for Firmware v4.
