| 3S PLUS 3S PLUS Motorcycle Bluetooth Headset & Intercom SENA www.senabluetooth.
| 3S PLUS © 1998-2013 Sena Technologies, Inc. All rights reserved. Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior notice. Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. Other trademarks and tradenames are those of their respective owners.
| 3S PLUS CONTENTS 1. INTRODUCTION 2. PACKAGE CONTENTS 3. INSTALLING THE 3S PLUS ON YOUR HELMET 4. POWERING ON/OFF AND CHARGING 4.1 Powering On 4.2 Powering Off 4.3 Charging 4.4 Low Battery Warning 5. CHECKING THE BATTERY LEVEL 5.1 LED Indicator 5.2 Voice Prompt Indicator 6. PAIRING THE 3S PLUS WITH BLUETOOTH DEVICES 6.1 Mobile Phone Pairing 6.2 Multipoint Mobile Phones Pairing 6.3 Bluetooth Stereo Device Pairing 6.4 Bluetooth GPS Navigation Pairing 7.
| 3S PLUS 1. INTRODUCTION Thank you for choosing the Sena 3S PLUS, Motorcycle Bluetooth Headset and Intercom. With the 3S PLUS, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigation by Bluetooth wirelessly, and have intercom conversations in full duplex with a passenger or other riders. The 3S PLUS is compliant with the Bluetooth Specification 4.
| 3S PLUS 2.
| 3S PLUS 3. INSTALLING THE 3S PLUS ON YOUR HELMET 1. [picture 3-1] Remove the left and right side cheekpads from the helmet. 2. [picture 3-2] 3. [picture 3-3] Place the speaker-microphone unit The boom microphone should be along with the velcro pad to the left positioned to face properly towards inside surface of the external shell, your mouth. Please make sure that the centered to your ear. microphone is located close to your mouth when you wear the helmet. 4. [picture 3-4] 5.
| 3S PLUS 4. POWERING ON/OFF AND CHARGING 4.1 Powering On Press the (+) Button and the (-) Button at the same time for 1 second to power on. The blue LED turns on and you will hear ascending beeps and “Hello”. 4.2 Powering Off Tap the (+) Button and the (-) Button simultaneously. The red LED turns on for about 2 seconds until it turns off completely and you will hear “Goodbye” and descending beeps. 4.
| 3S PLUS 5. CHECKING THE BATTERY LEVEL You can check the battery level in two different ways when the headset is powering on. 5.1 LED Indicator When the headset is powering on, the red LED flashes rapidly indicating the battery level. 4 flashes = High, 70~100% 3 flashes = Medium, 30~70% 2 flashes = Low, 0~30% 5.2 Voice Prompt Indicator When you power on the headset, keep pressing the (+) Button and (-) Button simultaneously for about 3 seconds until you hear three high tone beeps.
| 3S PLUS 6. PAIRING THE SMH3 WITH BLUETOOTH DEVICES 6.1 Mobile Phone Pairing 1. Turn on the 3S PLUS and press the (+) Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps. You will hear a voice prompt saying “Phone pairing”. 2. Search for Bluetooth devices on your mobile phone. Select the Sena 3S PLUS in the list of the devices detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN. 4.
| 3S PLUS 2. If Bluetooth connection between the headset and any other Bluetooth devices is disconnected, tap the (+) Button to recover the Bluetooth connection. 6.4 Bluetooth GPS Navigation Pairing You can listen to voice instruction from Bluetooth GPS navigation. Some GPS systems use mobile phone profile (HFP, Hands-Free Profile) and others use stereo music profile (A2DP, Advanced Audio Distribution Profile).
| 3S PLUS 8. 3S PLUS CONFIGURATION SETTING You can set the configuration of the 3S PLUS by the voice menu instruction as below. 1. To enter into voice configuration menu, press and hold the (+) Button for 10 seconds until the LED shows solid blue and you hear high tone double beeps. You will hear a voice prompt saying “Configuration menu”. 2. Tap the (+) Button to navigate between menus. You will hear voice prompts for each menu items as below. 3.
| 3S PLUS Factory Default Enable Enable / Disable Tap the (-) Button You can disable voice prompts by configuration setting, but the following voice prompts are always on. - Voice prompts for configuration setting menu - Voice prompts for battery level Indicator - Voice prompts for factory reset 8.
| 3S PLUS To exit voice configuration menu and get back to stand-by mode, tap the (+) Button until you hear a voice prompt, “Exit configuration”. Tap the (-) Button to confirm.
| 3S PLUS 9. USING THE 3S PLUS 9.1 Volume Adjustment You can easily adjust the volume by tapping the (+) Button or the (-) Button. You will hear a beep when the volume reaches maximum or minimum level. The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset. For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear Bluetooth MP3 music.
| 3S PLUS 2. To terminate an intercom conversation, press the (-) Button for 1 second again. [picture 11-2] 9.4 Intercom and Mobile Phone Call 1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation. ● To answer the phone call and stop the intercom conversation, tap the (+) Button.
| 3S PLUS SMH3 to remotely control music playback. So, You not only can adjust the volume but also use the functions such as play, pause, next track and previous track. ● To adjust the volume, tap the (+) Button or the (-) Button.. [picture 11-3] ● To play or pause music, press and hold the (+) Button for 1 second until you hear a double beep. [picture 11-4] ● To track forward or track back, press and hold the (+) Button or the (-) Button for 2 seconds until you hear a double beep. [picture 11-5] 9.
| 3S PLUS 10. FIRMWARE UPGRADE The 3S PLUS supports firmware upgrade function. Please visit Sena Bluetooth web site at www.SenaBluetooth.com to check the latest software downloads. SENA www.senabluetooth.com Users Guide for Firmware v1.
| 3S PLUS Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
| 3S PLUS fréquence et, s’il n’est pas installé et utilisé conformément. aux instructions, il peut occasionner des interférences nuisibles au niveau des communications radios. Cependant, il n’existe aucune garantie que ces interférences ne se produiront pas dans une installation particulière.