User Manual Copyright ⓒ 2019. Lab-T, Inc.
R1M Manual
1. GETTING STARTED: BUILT-IN BLUETOOTH SYSTEM 1.1 Button Functions 1.2 Powering On and Off Press and hold the Center Button and the (+) Button at the same time for 1 second to turn the headset on or off. 1.3 Charging The Bluetooth Communication Module can be charged using many common methods via the supplied USB power & data cable: 1. Plugged into a computer’s USB port. 2. With a USB-equipped AC adapter via a wall-outlet charger. Note: Please make sure to take off your helmet while charging.
1.5 Volume Adjustment You can raise or lower the volume by tapping the (+) Button or the (-) Button. Volume is set and maintained independently at different levels for each audio source (i.e., phone, intercom), even when the headset is rebooted. 1.6 Configuration Menu The Bluetooth Communication Module can be configured by following a series of voice prompts. Further details about each of these settings will be explained on the following pages. 1.
2.1 Mobile Phone 1. Execute Phone Pairing in the Configuration Menu. 2. With your mobile phone in Bluetooth-pairing mode, select Sena R1 in the list of devices detected. 3. If your mobile phone asks for a PIN, enter 0000. 2.2 MOBILE PHONE USAGE - Answer a Call : Tap the Center Button. - End/Reject a Call : Press and Holde the Center Button for 2 seconds. 2.3 Speed Dialing 1. Press and hold the (+) Button for 3 seconds to enter into the Speed Dial menu. You will hear the voice prompt, “Speed dial.” 2.
4. STEREO MUSIC 1. To play or pause music, press and hold the Center Button for 1 second until you hear a double beep. 2. To adjust the volume, tap the (+) Button or the (-) Button. 3. To track forward or back, press and hold the (+) Button or the (-) Button for 1 second. 5. LED Taillight - LED Taillight On : Tap the Center Button - Change the mode and LED Taillight Off Tap the Center Button continuously. LED On and Solid -> Night Flash -> Day Flash -> LED Off 6. USING THE FM RADIO 6.
6.4 Temporary Station Preset The Temporary Preset feature automatically finds and saves the nearest 10 radio stations without changing your existing preset stations. 1. Tap the (+) Button three times to automatically find and save 10 stations. 2. The temporary preset stations will be cleared when the Bluetooth Module reboots. 7. Fault Reset When the helmet’s Bluetooth Module is not working properly, you can easily reset the unit: 1. Locate the pinhole reset button below the (+) Button. 2.
Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules.
FCC, IC RF Exposure Statement The antenna used in this transmitter must be installed such that a minimum separation distance of 15.00 mm is always maintained from the human head. We, SENA TECHNOLOGIES.Inc confirm that when equipped in authorized helmet models, the distance between antenna and one’s head will not be less than 15.00 mm.
Certification et homologation de sécurité Déclaration de conformité FCC Cet appareil est en conformité avec la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d’interférences préjudiciables et (2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon fonctionnement.
É noncé FCC sur l’exposition aux radiations RF Cet équipement est conforme aux réglementations FCC d’exposition aux radiations définies pour un environnement non contrôlé. Les utilisateurs doivent respecter les instructions d’exploitation spécifiques pour répondre aux exigences de conformité sur l’exposition aux RF. L’antenne utilisée pour cet appareil ne doit pas fonctionner en même temps qu’une autre antenne ou émetteur, sauf s’il y a conformité avec les procédures FCC des produits multi-émetteurs.
FCC, IC RF Exposure Statement L'antenne utilisée dans cet émetteur doit être installée de manière à respecter un e distance minimale de 15.00 mm par rapport à la tête humaine. Nous, SENA TECHNOLOGIES.Inc confirmons qu’avec les modèles de casques autorisés, la dista nce entre l’antenne et la tête ne sera pas inférieure à 15.00 mm.