Bluetooth Class 1 OEM Module Parani-BCD110 Product Datasheet Version 1.0.0 February 9, 2012 Sena Technologies, Inc.
PARANI-BCD110 Copyright Copyright 2012, Sena Technologies, Inc. All rights reserved. Sena Technologies reserves the right to make changes and improvements to its product without providing notice. Trademark Parani™ is a trademark of Sena Technologies, Inc. Windows® is a registered trademark of Microsoft Corporation. Notice to Users When a system failure may cause serious consequences, protecting life and property against such consequences with a backup system or safety device is essential.
PARANI-BCD110 Contents 1. General .......................................................................................................................................................... 4 1.1 Features ............................................................................................................................................... 4 1.2 Applications .......................................................................................................................................... 4 1.
PARANI-BCD110 1. General The Parani-BCD110 is a Bluetooth Class 1 OEM module for OEM manufacturers who want to implement Bluetooth Class 1 functionality with their products cost effectively and also in timely manner. Users can build their own antenna circuit around the BCD110 to lower the overall cost while benefit from the BCD110’s fieldproven standard SPP (Serial Port Profile) firmware provided with no additional cost.
PARANI-BCD110 1.3 Device Diagram Parani-BCD110 2402 ~ 2480MHz USB 2.4GHz Antenna 5dBi dipole 3dBi dipole 1dBi stub 0dBi chip RF_IN/OUT RF Amplifier Circuit RAM UART 2.4GHz Radio Baseband DSP LNA IO SPI Voltage Regulator 1.8V core Interface Pad or connector MCU PA PIO BlueCore4 External PCM Crystal 26MHz Flash Memory 8Mb Figure 1-1 Device Diagram 1.4 Pin Diagram Figure 1-2 Pin diagram Page 5 of 26 VCC 3.
PARANI-BCD110 1.
PARANI-BCD110 Function USB UART PCM SPI PIO AIO Others Pin Name STATE Define (SPP) Direction Pull-up/down USB_DP - Input Weak pull-up USB_DN - Input Weak pull-up UART_TXD UART_TXD Output Tri-stated with weak pull-up UART_RXD UART_RXD Input Weak pull-down UART_RTS UART_RTS Output Tri-stated with weak pull-up UART_CTS UART_CTS Input Weak pull-down PCM_OUT - Output Tri-stated with weak pull-down PCM_IN - Input Weak pull-down PCM_SYNC - Input Weak pull-down PCM_CLK
PARANI-BCD110 1.
PARANI-BCD110 Figure 1-7 BCD110DS Dimensions [SMD Type] [DIP Type] Figure 1-8 Recommended Land Pattern Page 9 of 26
PARANI-BCD110 Figure 1-4 Recommended Board Layout *BCD110SU, DU, DS has no keep-out area. Model despription Antenna Model name Interface Connector Type1 Type2 Type3 Parani-BCD110DU DIP, pin U.FL 5dBi dipole 3dBi dipole 1dBi stub Parani-BCD110DS DIP, pin RPSMA 5dBi dipole 3dBi dipole 1dBi stub Parani-BCD110DC DIP, pin CHIP 0dBi Chip Parani-BCD110SU SMD, pad U.
PARANI-BCD110 2. Electrical characteristics 2.1 Absolute maximum ratings Ratings Min Max Unit Storage Temperature -40 +85 °C Operating Temperature -40 +85 °C Supply voltage PVCC -0.4 3.6 V +3V3 -0.4 3.6 V GND – 0.4 +3V3 +0.4 V Other terminal voltages Table 2-1 Absolute maximum ratings 2.2 Recommended operating conditions Ratings Min Typ Max Unit Operating Temperature -40 25 +85 °C Supply voltage PVCC 2.7 3.3 3.6 V +3V3 2.7 3.3 3.6 V UART 3.0 3.3 3.
PARANI-BCD110 3. RF Characteristics 3.1 Basic Data Rate 3.1.1 Transmitter Performance RF Characteristics Min Typ Max Bluetooth PVCC = 3.3V, 25°C Unit Specification Output power 16 18 19 ≤ 20 dBm Power Density 16 18 19 ≤ 20 dBm Power Control 3 4 6 2 ≤ step ≤ 8 dB TX Output Spectrum-Frequency range 2402 - 2480 2400 ~2483.
PARANI-BCD110 F = F0 + 2MHz - - -20 ≤ -20 dB F = F0 – 2MHz - - -30 ≤ -30 dB F = F0 – 3MHz - - -40 ≤ -40 dB F = F0 + 5MHz - - -40 ≤ -40 dB - -9 ≤ -9 dB F = FImage Blocking 0.030-2.000GHz -10 - - ≥ -10 dBm performance 2.000-2.400GHz -27 - - ≥ -27 dBm 2.500-3.000GHz -27 - - ≥ -27 dBm 3.000-12.75GHz -10 - - ≥ -10 dBm Inter-modulation performance -39 - - ≥ -39 dBm Maximum input level at 0.
PARANI-BCD110 3.2.2 Receiver performance RF Characteristics Min Typ Max Temperature 25°C Bluetooth Unit Specification Sensitivity π/4 DQPSK - -88 -70 ≤ -70 dBm at 0.01% BER 8DPSK - -85 -70 ≤ -70 dBm - - -60 ≤ -60 dBm BER floor performance C/I Performance π/4 DQPSK - - 13 ≤ +13 dB (co-channel at 0.
PARANI-BCD110 4. Device Terminal Descriptions 4.1 UART Interface UART (Universal Asynchronous Receiver and Transmitter) interface provides a simple mechanism for communicating with other serial device using the RS232 protocol. When BCD110 is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The remaining two signals, UART_CTS, UART_RTS, can be used to implement RS232 hardware flow control where both are active low indicators.
PARANI-BCD110 4.3 I2C Interface PIO[8:6] can be used to form a mater I2C interface. The interface is formed using software to drive these lines. Therefore, it is suited only to relatively slow functions such as driving a dot matrix LCD (Liquid Crystal Display), keyboard scanner or EEPROM. Notes: PIO lines need to be pull-up through 2.2KΩ resistors. PIO[7:6] dual functions, UART bypass and EEPROM support, therefore, devices using an EEPROM cannot support UART bypass mode.
PARANI-BCD110 BCD110 has three general purpose analogue interface pins, AIO_0 and AIO_1. These are used to access internal circuitry and control signals. One pin is allocated to decoupling for the on-chip band gap reference voltage, the other two may be configured to provide additional functionality. 4.6 Reset Interface BCD110 may be reset from several sources: RESETB pin, power on reset, a UART break character or via a software configured watchdog timer.
PARANI-BCD110 5.
PARANI-BCD110 Figure 5-3 RS232 Serial Interface Figure 5-4 MICOM UART Interface Page 19 of 26
PARANI-BCD110 Figure 5-5 USB Interface Figure 5-6 I2C Interface Figure 5-7 PCM Interface Page 20 of 26
PARANI-BCD110 6. Software Stack BCD110 is provided with Bluetooth v2.0 compatible firmware runs internally for SPP (Serial Port Profile) applications by default. The firmware is designed to work out-of-box for real world SPP applications such as POS (Point-of-sales), industrial automation, remote metering and other various applications. The SPP firmware can be configured and controlled by typical AT commands.
PARANI-BCD110 7. Solder Profiles The soldering profile depends on various parameters necessitating a set up for each application. The data here is given only for guidance on solder re-flow. There are four zones: Preheat Zone – This zone raises the temperature at a controlled rate, typically 1-2.5°C /s Equilibrium Zone – This zone brings the board to a uniform temperature and also activates the flux.
PARANI-BCD110 8.
PARANI-BCD110 TBD Figure 8-2 Reel Information Page 24 of 26
PARANI-BCD110 9. Certificate Information 9.1 FCC FCC Rule: Part 15 Subpart C Section 15.247 FCCID: S7AIW02 9.1.1 FCC Compliance Statement This device complies with part 15 of the FCC Rules.
PARANI-BCD110 9.2 CE 1177 Declare under our own responsibility that the product Bluetooth Module Brand name: SENA Model No.: Parani-BCD110DU / Parani-BCD110DC / Parani-BCD110DS Parani-BCD110SU / Parani-BCD110SC To which this declaration refers conforms with the relevant standards or other standardizing documents EN 60950-1 ETSI EN 301 489-1 ETSI EN 301 489-17 ETSI EN 300 328 According to the regulations in Directive 1999/5/EC 9.
