User's Manual

ManualsBrandsSeiko Instruments ManualsElectronicsModule

IFWL-001 User’s Manual

Overview

IFWL-001 is a Wireless LAN module for Seiko Instruments Printer.

This module provides functions for printing over Wireless LAN.

Install and set default value

1. Install IFWL-001 to Printer with 12pin FFC.

2. Turn the power ON and set default value from Web page or USB connection on FFC.

Web page: http://192.168.0.1

To set default value with USB connection, use commands by vendor request on USB.

For more detail information, please see specifications document.

How to use

1. #9100 port

Connect #9100 port and send printer command.

2. LPR port

Connect LPR port and send data with LPR protocol.

3. #26100 port

Connect #26100 port and send SVRP command.

Specifications

Standard: 802.11b/g/n, 802.11a/n

Input voltage: 3.0 to 3.6V

Maximum current: 500mA

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference, including interference that may cause

undesired operation.

Summary of content (5 pages)

PAGE 1
IFWL-001 User’s Manual Overview IFWL-001 is a Wireless LAN module for Seiko Instruments Printer. This module provides functions for printing over Wireless LAN. Install and set default value 1. Install IFWL-001 to Printer with 12pin FFC. 2. Turn the power ON and set default value from Web page or USB connection on FFC. Web page: http://192.168.0.1 To set default value with USB connection, use commands by vendor request on USB. For more detail information, please see specifications document. How to use 1.
PAGE 2
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Operations in 5150-5250 MHz band is for indoor use only. Requirements to end product This module must be integrated only by OEM integrators under the following conditions.
PAGE 3
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
PAGE 4
1) l’appareil ne doit pas produire de brouillage; 2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF exposure compliance 1) To comply with FCC/IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 5
Seiko Instruments Inc. 1-8, Nakase, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan Print System Division Telephone:+81-43-211-1106 Facsimile:+81-43-211-8037 Seiko Instruments USA Inc. Thermal Printer Div. 21221 S. Western Avenue, Suite 250, Torrance, CA 90501, USA Telephone:+1-310-517-7778 Facsimile:+1-310-517-7779 Seiko Instruments GmbH Siemensstrasse 9, D-63263 Neu-lsenburg, Germany Telephone:+49-6102-297-0 Facsimile:+49-6102-297-222. Seiko Instruments (H.K.) Ltd.