NF05628-1.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
11. ACCESORIES 12. CAUTION CAUTION: RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE. BATTERY INSTALLATION AND REPLACEMENT MUST BE CARRIED OUT BY PERSONNEL IN POSSESSION OF ENOUGH TECHNICAL KNOWLEDGE, EXPERIENCE OR INSTRUCTIONS TO BE xxx xxx-xxxxxx ABLE TO PROPERLY PERFORM THE CONNECTIONS. DONOT USE THIS PRODUCT IN CLOSE PROXIMITY TO WATER. DO NOT USE THIS PRODUCT NEAR ANY HEAT SOURCE AND KEEP IT AWAY FROM NAKED FLAMES. 19 1. IMPORTANT SAFETY INFORMATION 1 2. FEATURES 2 3.
10.
9. TECHNICAL SPECIFICATIONS FEATURES 6.5” All-In One PA system Frequency UHF(470~494),(542~566),(863~865)MHZ Bands Dependent on applicable country regulations Power Supply AC:100V/110-240V/ Battery:25.9V(lithium) System Type 2-Way Active All-in-one PA system Transducer Low 6.5 Woofer Transducer High 1 Neodymium driver Frequency Response(-6dB) 70Hz-16KHz Crossover Frequency 1.
8.WIRE CONNECTIONS CONTROL ELEMENTS Both connectors,1/4” XLR or TRS, can be wired in balanced or unbalanced way, depending on the work necessity. The following ones are examples of how these connectors can bewired: As to these circumstances, audio connections is mostly intended for the signal flow, so, determine the wire configuration according to your real application system and its connecting facility.
Microphone Receiver Press this key to search for a channel number. Press this key to adjust parameters inside the receiver. Press this key to search for a channel number. Display Here displayed channel and signal information for radio frequency(RF) and audio level(AF). Volume control Adjusts the level of the microphone signal. Mixer Channel 1 Volume Control Controls the input signal level of channel 1. Channel 2 Volume Control Controls the input signal level of channel 2.
18 19 20 21 22 23 Priority Selector Pressing this selector will give output priority to the microphone connected on channel 1 over all other channels. Aux/MP3/Bluetooth Volume Control This control adjusts the signal level coming from the Aux channel or MP3 music player or Bluetooth. Line Selector/Hi-Z Channel 2 This switch changes the impedance of the Line level channel or High lmpedance level.
6.CABINET POSITIONS This multifunctional and portable cabinet has three modes of operation and sound projection depending on the application and the place where you work. Thanks to internal switches and equalizers, the system changes the response curve automatically to maintain optimum balance in each position. Elevated Surface Place the speaker on a raised surface or on a speaker stand. This position allows greater projection of sound in full range to the audience.
4. RECEIVER(RX)OPTIONAL HOW TO PAIR YOUR RECEIVER AND TRANSMITTER Power on your receiver, Then select the channel you like or scan the cleanest channel automatically according to above steps. Then quick the “SET” button and release it to enter pair mode. Power on your transmitter, Then place the IR port of receiver to face towards the IR lens of transmitter within 20cm distance. Once TX and RX are paired successfully. The RF/AF indicator on receiver will light solid.
Pin 2:“Phantom Power” for condenser microphones Pin 3:Designed for musical instruments(When used with cable) Pin 4:Desugbed for use with dynamic or condenser microphones Infrared(IR) This window is used to capture the infrared signal sent from the receiver. During IR adjustment to pair the transmitter with the receiver, the IR lens must face the receiever to load the selected channel. Gain Control This control adjusts the input sensitivity for working with microphones or musical instruments.
5.TRANSMITTER(TX) There are three types of transmitters dedicated to our customer. Customer can select the transmitters according to their preferences. Option#1 HANDHOLD TRANSMITTER Protecton Grid Microphone Body Battery Cover Insert two standard AA(1.5V) batteries here, making sure that the positive and negative polarity marks are oriented correctly, Although NI-CAD rechargeable batteries can be use, this transmitter cannot recharge them.