User Manual IoT Device Model: PJ22IOT
1.Introduction Thank you for purchasing the IoT devices of Segway Inc.! The IoT device is designed for the shared scooter and it could communicate with the cloud server via cellular communication. Our IoT device is highlighted with the following features. First of all, you could fully control the scooter, such as lock/unlock, power on /off, turn on/off the throttle, and switch between different riding modes, etc.
2.
2.Basic Parameters Item Specification Voice Prompts Factory Defaults; Volume:70-90dB Motion Detection Triaxial Accelerometer Operating Temperature -20℃ ~ 60℃ Storage Temperature -40℃ ~ 70℃ Operating Humidity 93%RH IP Rating IPX7 Unlocked state current <40mA (36VDC average current) Lock state (standby) current <5mA (36VDC average current) Battery&Communication Interfaces 5pin:36V,GND,TX (TTL),RX (TTL), Power_control_wire Battery Supply Voltage 36VDC Built-in Lithium Battery 3.
3.Main Features Main Features(Firmware Version: SD1.0.5) *This will be continuously updated Lock&unlock, power on/off through both 4G and BLE4.0. Two modes to locate: Single/Continuous Adjustable sensitivity of accelerometer User-defined communication interval between server and IoT Headlight switch: manual or programmable Enable/Disable Riding Modes Switch Riding modes switch:manually or programmable Enable/Disable Throttle, Cruise control, Front&rear lights flash Searching scooter module User-defined Max.
4.Diagram a. IoT Device*1 b. Rubber Stopper *4 c. Fixer (U-shaped holder and board part)*1 d. Screw (M5*12)*4 e.
5.
6. Assembling a. The stem: Remove the four anti-theft screws fixed to dismantle the stem.
6. Assembling b. The U-shaped holder: Put it on the stem and move it to the position as shown in the picture. Then reassemble the stem.
6. Assembling c.The board part: First, pull the 5 pin cable of the scooter through the hole on board part. Second, after locating the board part according to the 2 screws on the stem, mount the 4 screws (M5*12) to attach the board part to the U-shaped holder.
6. Assembling d. The IoT device: First, connect the 5 pin cable of the scooter with that of the IoT device. Second, mount the 4 screws(M4*12) to attach the IoT device to the board part. Third, mount the 4 rubber stoppers to the holes on the IoT device.
7.Notes 1. Do not use the IoT device beyond the operating temperature range: -20℃ ~ 60℃. 2. Do not dismantle the IoT device to change SIM card inside because this will weaken its waterproof performance. 3. Keep the IMEI code label and Serial Number code label adhered on the IoT device intact. 4. Fixer may vary depending on the model of the scooter. 5. Environment surroundings, terrain and other factors may affect the signal quality of GPS and cellular communication. 6.
8. Regulatory Info FCC Regulatory Compliance Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
8. Regulatory Info Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: Trade Name: Segway Model No.: PJ22IOT Responsible Party – U.S. Contact Information Segway Inc. 14 Technology Drive, Bedford, NH 03110 Phone: +1 603-222-6000 Fax: +1 603-222-6001 www.segway.com FCC Compliance Statement This device complies with Part 15 of the FCC Rules.
8. Regulatory Info ISED Regulatory Compliance This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
8. Regulatory Info This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé.
Hereby, Ninebot (Changzhou) Tech Co., Ltd declares that the radio equipment type PJ22IOT is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.segwaydiscovery.com/downloads/User_Manual_of _IoT_device_PJ22IoT.pdf Segway Inc. 14 Technology Drive, Bedford, NH 03110 Phone: +1 603-222-6000 Fax: +1 603-222-6001 www.segway.
