Quick Start Guide

Indicator Volume +
Pause/Next
Vibrating
diaphragm
Install the App and register/log in.
Press the power button on the S-Max to turn on the Gokart Pro.
The Gokart will automatically power off when idle for 10 minutes.
Open the App, Click Vehicle > Search device to connect to your
Gokart Pro. The vehicle will beep when the connection is
successful. The Bluetooth icon will stop blinking and remain
illuminated.
Follow the instructions in the app to activate the
Gokart and complete the corresponding tutorial and
exercises.
Remove the Speaker：Press the disassembly
switch while lifting the speaker upward.
Quick Start Guide
1 Adjustment
4 Learning to Drive
3 Before the First Drive
Scan the QR code
above to watch the
Disassembly and
Riding Safety Video.
Stretch the frame and adjust the length
of the body
How to activate:
Riding Safety
Correct dress code
a
b
b
c
d
a
turn on
mode
Indicator
b
c
d
f
b Press the remaining part of the strap into
the storage slot.
Install the Ninebot Engine Speaker
b
c
a
b
a
L
R
base
1
2
3 4
5
Rear Spoiler
AA Battery
Compartment
Brake
(left)
Support rods
(Ninebot Engine Speaker location)
The assembled
GoKart Pro
a
a With both hands holding the steering wheel and the
seat, stretch the frame out to a suitable position
along the horizontal direction of the connection
tube.
b Align the scalable structure of the frame with the
marking on the connection tube.
c Positioning: Use the short hex wrench to press the
two screws into the holes on the left and right
connection tube in order, as shown in the figure on
the right (The screw is set to a depth of about 1 cm
for successful position).
d Tighten the 4 screws.
Four screws are already
inserted into the screw holes.
Adjust the steering wheel height
a Raise the steering wheel to a suitable height.
b Insert the quick release screw into the hole of
the corresponding height.
（Insert the quick release screw into the hole of
the corresponding height.）
c Tighten the quick release nut.
d Press to fix the steering wheel quick-release
components.
e Ensure the steering wheel does not shake.
Otherwise, repeat the steps b, c, d, e.
Remove the speaker before adjusting the
height of the steering wheel.
2 Installation of Accessories
Note: Do not press or lift the rear spoiler during installation.
a. Insert the rear spoiler bracket into the slot.
Install the Rear Spoiler
b Use the 2.5 mm hex wrench to tighten the 6 screws into
the main body of the rear spoiler. (See Accessory No. 2).
a Place the base in a proper position (as shown below) and
wrap the strap around the vehicle body and fasten the
strap.
c Align the holes on the bottom of the speaker. Press
down until you hear a "click" sound.
* For more information about the speaker, see the user manual of Ninebot Engine Speaker.
Segway-Ninebot App
For your safety, a new Gokart is inactivated. Please activate your Gokart via the App
before first use.
You can also find our app in the Apple App Store as well as the Google Play Store,
simply search "Segway-Ninebot"
Press the power switch to turn on the speaker.
Press and hold the Mode button to start pairing.
Ninebot Engine Speaker:
* The Speaker and the App cannot be connected to the Gokart at the same time. If you have connected the App,
disconnect the App from the Gokart first, confirm that the indicator light of the Gokart is flashing blue, and then pair the Speaker.
Horn Power
switch
Volume -
Mode
USB Type-C
You are at a risk of injury when driving a Gokart,
please dress properly as shown in the picture.
Minors must learn and drive under adult
supervision.
Wear a helmet
Tie up long hair (if any)
Zip up the zipper
No long skirts
Wear flat shoes
Wear
protective
gear
When the Gokart is stopped, double-press the
brake (left pedal). After you hear a beep,
the Gokart has switched to reverse mode. Press
the throttle to drive the Gokart in reverse.
Double-press the brake (left pedal) again to
return to forward mode.
3
Reversing
Acceleration: lightly press the throttle (right pedal)
to go forward.
Deceleration: lightly press the brake (left pedal) to
decelerate.
* Do not pump the brake pedal to decelerate.
Steering: steer the Gokart by slightly turning the
steering wheel clockwise or counterclockwise.
2
Driving
1
Sitting on the seat, buckle the left and right parts of
the seat belt in front of you.
Fastening the seat belt
4
In the event of a situation that requires an
emergency stop, pull the hand brake handle on
the right side of the Gokart to engage the
emergency brake.
* Only use the emergency brake when necessary.
Frequent use can deform the tire.
Emergency braking
Adjust the knee pad height
Tighten the two screws.
(See Accessories No. 3)
Put the cap on.
Ninebot S-Max Quick Start Guide
1 Remove the S-Max body form the Gokart
(Hereinafter referred to as S-Max)
3. Remove the adaptor
pad of S-Max.
Sudden speed change and turns are forbidden during riding.
Rider can be seriously injured with such actions.
When the vehicle tilts back or sounds alarm, please slow down
immediately till the vehicle is back to the normal position.
Water contact with Li-ion battery can increase the risk of fire.
Do not expose the vehicle in the rain or ride it in the rain for a long
period of time. When the vehicle is not used, please store it in dry
and cool surrounding.
Charge the battery in time to avoid over-discharging and cause damage.
The standby time is around 120 to 180 days when the battery
is fully charged. Please charge the battery in time or
over-discharging may cause damage.
4 Warnings and Cautions
Gokart mode
1 2
3 4
1
2
3
1
2
2 Assembling Your S-Max
3 Before the First Ride
Power off the Gokart before disassembly.
1. Rotate counter-clockwise
to unplug the power
extension cord.
2. Loosen the traps and take out
the S-Max body.
* If lifting the frame by yourself,
do not lift the backside more
than 19° or you may damage
the bumper.
Do not lift the Rear Spoiler.
Install the steering bar
Insert the steering bar into the S-Max body. Rotate the height adjustment knob
counter-clockwise.
Lift the knee pads to the desired
height. Rotate the height adjustment
knob clockwise to tighten.
* Lift the guide bar to help steer the
S-Max without a rider when powered
on.
WARNING
DO NOT use to lift or carry the S-Max.
There are safety risks when learning to ride the S-Max. You must read the Safety Instructions and follow the New Rider Tutorial
in the App before your first ride.
For your safety, your S-Max is not activated at this time and will beep occasionally after Power ON.
Until activated, the S-Max maintains a very low riding speed and steering sensitivity. Install the App on your mobile device (with
Bluetooth 4.1 or above), connect to the S-Max with Bluetooth, and follow the App instructions to activate your S-Max and follow
the training procedures.
Scan the QR code to download the App (iOS 9.0 or above, Android™ 4.3 or above).
Segway-Ninebot App
Power ON the S-Max. The Bluetooth icon blinking indicates the S-Max
is waiting for a connection.
BEFORE RIDING, MAKE SURE TO SWITCH THE S-MAX TO
SELF-BLANCING MODE IN THE APP. Follow the prompts to watch the
Riding Safety video, complete the New Rider Tutorial, and then activate
the S-Max.
* When the mode is switched successfully, you will hear two beeps.
Install the App and register/login.
Click Vehicle > Search device to connect to your S-Max. The S-Max
will beep when the connection is successful. The Bluetooth icon will
stop blinking and remain illuminated.
Wear an approved helmet and other protective
gear to minimize any possible injury.
Basic info and settings
WARNING
EN
FR