User Manual By Firstech LLC, Version: 1.0 Applicable to the following remote(s); 2W902R-SP 2 Way 5 Button LED Remote & ANT-2WSP 2Way Antenna Remote & Antenna FCC ID Number (US Only) IC ID Number (International Only) 2W902R-SP VA5REC500-2WSP 7087A-2WREC500SP ANT-2WSP VA5A1000-2WSP 7087A-2WA1000SP This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions; This device complies with Industry Canada licence-exempt RSS standard(s).
Introduction ..................................................................................................................................................3 Warranty Coverage ......................................................................................................................................3 Quick Reference ...........................................................................................................................................4 Button Lock ............................
Introduction Thank you for purchasing a Firstech system for your vehicle. In order to truly enjoy the benefits of this system, we recommend that you thoroughly review the following manual. Please note that this manual applies to the 2 Way 5 Button LED Remote (2W902R-SP) Regardless of whether you purchased the ALARM IT, START IT, or MAX IT system. This manual also supports the 1WG7R-SP that is included in your new RF Kit.
Quick Reference Button Lock The 2W902R-SP comes equipped with automatic button lock. This requires you to tap any button to wake your remote up then tap the button for the function you are trying to activate. Button lock can be turned off in your remote’s option menu. Full or Half Paging Mode The 2W902R-SP is shipped in Half Paging Mode. This means that the remote will only receive 2 Way LED confirmations for remote start and lock and unlock. It will not receive 2 Way LED confirmations buttons for 2.
2W902R-SP: Turn the remote over and unlock the battery cover by sliding the clear tab up. Slide the battery cover off, revealing the AAA battery. IMPORTANT: Be sure to observe correct polarity when installing the battery. 1WG7R-SP: Use a quarter or flat head screwdriver to pry the back cover off of the remote. You can insert the quarter or flat head in the small slot at the bottom of the remote by the keychain loop. Carefully pry off the back cover using caution that you do not damage the circuit board.
and Key Icon> 2.5 seconds Accesses Remote Option Menu. See Remote Option Menu Table for details. Function Button Menu Button Duration One Tap Drive Lock On/Off Turbo Timer On/Off Auxiliary 1 Auxiliary 2 Remote Option Menu Table Feature Turns Feature On or Off Button Duration Remote Chirp(s) Function / Description Enter and Exit Remote Menu 2.
Alarm LED Notifications In the event that your alarm has been triggered, your remote will receive notifications based on what zone has been violated. Please see the following table for details and a short description of each notification. Please note that these notifications are only available with MAX IT and ALARM IT systems.
2.5 seconds no Option programming menu 2 - Installers Only. Half second no Activates passive arming (vehicle will arm/lock 30 seconds after the vehicle is disarmed) Half second yes Activates timer start mode. Timer start mode has multiple programmable settings: duration settings, temperature settings and self start settings. Half second yes Activates the built in Turbo Timer function. Additional installation is required when using this feature on automatic transmission vehicle’s. 2.
arming mode. While in passive mode, the system will lock and arm the alarm 30 seconds after the last door is closed. As an indicator that the vehicle is going to passively lock and arm, the remote and siren will chirp once and the parking lights will flash once at both 10 and 20 seconds prior to passively locking and arming. If you want the system to passively arm and not passively lock, ask your local Firstech dealer to turn Option 1-8 to setting II.
Once the vehicle shuts off your system is in reservation mode and the vehicle is ready to safely remote start. IMPORTANT: By default, the system will lock/arm the vehicle upon setting reservation mode. Take care to not lock your keys inside the vehicle. Cancelling Reservation Mode Reservation mode will be cancelled for the following reasons; You did not activate the parking brake prior to turning off the ignition. You pressed the foot brake after the key was removed from the ignition.
simultaneously for a half second. IMPORTANT: Even when the siren is muted, it will still go off in the event the alarm is triggered. Remote Mute To silent your remote you must turn on Remote Mute on; STEP 1: Enter remote programming mode by holding the Trunk and Key/Start buttons simultaneously for 2.5 seconds. The remote will beep 3 times and the LED will flash purple indicating that you have successfully entered programming mode. STEP 2 : Tap the Unlock button.
Advanced System Functions The following section reviews advanced system functions. Many of these functions require multiple steps or additional programming by your local authorized Firstech dealer to be active. Drive Lock/Ignition Controlled Door Locks Tap the Function button once followed by the Lock button to turn the Drive Lock on and off. (also known as ignition controlled door locks) The remote will beep once and the LED flash once to confirm that drive lock mode is activated.
RPS Touch and RPS (Remote Paging Sensor) The RPS is an optional feature. The car call/RPS feature uses a small sensor that is mounted on the inside of your windshield. RPS Touch (Remote Paging Sensor) The new RPS touch has multiple features including: remote paging, 4 digit pin unlock/disarm, and arm/lock. All features are operated with a simple touch of the sensor. Please have your installer program Option 3-16 to Setting 2.
STEP 1: Enter remote programming mode by holding down the Trunk and Key/Start buttons simultaneously for 2.5 seconds. The remote will beep once and the LCD will read “REMOTE MENU” indicating that you have entered programming mode. STEP 2 : Scroll through the remote options by taping the Function button . Once the LCD reads “RPS-ON” tap the Lock button to turn this feature on.
Secure Valet Switch The optional Secure Valet Switch prevents the alarm from being put into valet mode through cycling the ignition on/off five times. The Secure Valet Switch is more secure than traditional toggle / valet switches because it requires a two digit code. IMPORTANT: The first two digits of the RPS unlock/disarm pass code will be the default pass code for the secure valet – you do not need to program them independently.
Remote Coding / Programming Routine IMPORTANT: Every Firstech remote must be coded to the system prior to performing any operations. All remotes must be coded at the same time. Programming 2 Way 5 Button Remotes: STEP 1: Activate Valet/Programming mode by manually turning the ignition key on and off (between the Acc & On positions) five times within 7 seconds. The vehicle’s parking lights will flash once with the successful completion of this step.
Alarm Diagnostic While the alarm is armed, the LED will blink slowly. While the siren is going off, the LED will indicate which specific zone was triggered.
Limited Lifetime Warranty Firstech, LLC Warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for the period of time that the original owner of this product owns the vehicle in which it is installed; except that the remote controller unit for the period of one year from the date of installation to the original owner of this product.