WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module Integrated Bluetooth 2.1/3.0/4.2/5.0 特性 Features： ➢ 接收制式 Supported WLAN Standard IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11a IEEE Std. 802.11ac Bluetooth 2.1/3.0/4.2/5.0 ➢ 芯片方案 Chip Solution Realtek：RTL8822CU ➢ 结构大小 Size 19.0mmx 17.0mm x 2.6mm 型号 安装方式 WF-R22C-USA1 SMD 支持标准 速率 频段 IEEE802.11 a/b/g/n/ac 866.7Mbps 2.4G/5G 3 Mbps 2.4G BT 2.1/3.0/4.2/5.0 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 客户确认反馈 Feedback of customer’s Confirmation 经确认，我方承认该规格书 We accept the specification after Confirmed 客户名称 Customer name 客户签字 Customer signature 确认日期 Confirmation Date 请签字后将此页与首页按以下地址回传我公司，谢谢！ Please feed back this paper and first paper after your signature by the address,thanks! 地址：四川省绵阳市安州工业园区 ADD： Anzhou,Industrial park,Mianyang,Sichuan 公司：四川爱联科技有限公司 Factory： Sichuan AI-Link Technology Co.,Ltd.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 更改记录 Record of Modification 版本 Version V1.0 更改日期 Date of modification 2019/3/14 主要更改内容 Main content of modification 首次承认 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 1. Introduction WF-R22C-USA1 module design is based on RTL8822CU-CG solution, The Realtek RTL8822CU-CG is a highly integrated single-chip that support 2-stream 802.11ac solutions with Multi-user MIMO (Multiple-Input, Multiple-Output) with integrated Bluetooth 2.1/3.0/4.2/5.0 controller,USB interfac. It combines a WLAN MAC, a 2T2R capable WLAN baseband, and RF in s single chip.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 1.3 System Functions Table1: General Specification as below: Main Chipset Operating Frequency WIFI Standard Bluetooth Modulation Data rates Form factor Host Interface PCB Stack Dimension RTL8822CU 2.4G/5G 802.11a/b/g/n/ac (2x2) 2.1/3.0/4.2/5.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L ): 19.0mmx 17.0mm x 2.6mm General tolerance: ±0.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0℃,+25℃,+40℃) and overall voltage (3.0V,3.3V,3.6V). 3. 1 IEEE 802.11g /a Section: Items Specification Mode Channel Data rate TX Characteristics 1. Power Levels 1) 15dBm Target (For Each antenna port) @ 11g 2) 14dBm Target (For Each antenna port) @ 11a 2.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.2 IEEE 802.11b Section: Items Contents Specification Mode Channel Data rate TX Characteristics 1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port) @1Mbps~11Mbps 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3. Constellation Error(EVM) @ Target Power 1) 1Mbps 2) 2Mbps 3) 5.5Mbps 4) 11Mbps 4. Frequency Error RX Characteristics 5.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.3 IEEE 802.11n HT20 Section: Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels 1) 14dBm Target (For Each antenna port) @ 2.4G/MCS0~MCS7 2) 13dBm Target (For Each antenna port) @ 5G/ MCS0~MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.3 IEEE 802.11n HT40 Section: Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels 1) 14dBm Target (For Each antenna port) @ 2.4G/MCS0~MCS7 2) 13dBm Target (For Each antenna port) @ 5G/MCS0~MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.4 IEEE 802.11n ac Section: Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels 1) 13dBm Target (For Each antenna port) @MCS0~MCS9 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 9) MCS8 10) MCS9 4. Frequency Error 1) IEEE802.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.5 Bluetooth Specification 3.5.1 BR Specification Items Host Interface Antenna Reference Channel Modulation TX Characteristics 1.Output Average Power 2.Modulation Characteristics 1)Delta f1(Avg) 2)Delta f2max(For at least 99.9% of all Delta f2max) 3)Delta f2/ Delta f1 3.Initial Carrier Frequency Tolerance 4.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.5.2 EDR Specification Items Host Interface Antenna Reference Channel Modulation TX Characteristics 1.Relative Transmit Power 1) π/4-DQPSK 2) 8PSK 2. Frequency Stability 1) Omega-i 2) Omega-0 3) Omega-0 + Omega-i 3. Modulation Accuracy 1) RMS DEVM π/4-DQPSK 8PSK 2) Peak DEVM π/4-DQPSK 8PSK 3) 99% DEVM π/4-DQPSK 8PSK RX Characteristics 1. Receiver Sensitivity (BER<0.01%) 1) π/4-DQPSK 2) 8PSK 2. Maximum usable signal (BER<0.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 3.5.3 LE Specification Items Host Interface Antenna Reference Channel TX Characteristics 1. Output power at NOC 2. Modulation Characteristics 1)Delta f1(Avg) 2)Delta f2max(For at least 99.9% of all Delta f2max) 3)Delta f2/ Delta f1 3. Carrier frequency offset and drift 1) Frequency Offset 2) Frequency Drift 3) Max Drift Rate 4.In-band Spurious Emissions 1)+/-2M offset 2)>+/-3MHz offset RX Characteristics 1.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 6.Key component List 序 号 关键件名称 型号 1 集成电路 RTL8822CU 规格/材料 FR-4,4LAY， 1mm PCB 3 晶体振荡器 3225 40M 4 双工器 1608 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. 备注 REALTEK 2 JUI7.820.
WF-R22C-USA1 IEEE 802.11 a/b/g/n/ac 2T2R USB WIFI Module&BT 2.1/3.0/4.2/5.0 7.Package 箭头代表编带的走向 1、产品放置方向、标签粘贴位置、包装按示意图进行； 2、每卷放900只产品，每小盒放1卷，大箱共装5个小盒，产品数量共4500只/箱; 3、外箱尺寸：370mm*300mm*370mm，小盒尺寸：355mm*355mm*55mm; 4、真空包内放置2g干燥剂2袋，6色湿度卡1张; 5、其它未尽事宜按客户的包装要求执行。 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditio ns: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
End Product Labeling If the FCC identification number is not visible when the module is installed insideanother device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AFG6‐WF‐R22C‐USA1. Table for Filed Antenna For BT&BLE Antenna Type Antenna Gain For WIFI 2.4G &5G Antenna Type Antenna Gain Dipole Antenna 2400MHz‐2500MHz: 3.
ISED Statement ‐ English: This device complies with Industry Canada license‐exempt RSS standard(s).Operation is s ubject to the following two conditions: (1) This device may not cause interference, and (2) This devic e must accept any interference, including interference that may cause undesired operation of the de vice.The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B). ‐ French:Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Note Importante: Dans le casoùces conditions ne peuventêtresatisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co‐localisation avec un autreémetteur), l'autorisation du Canada n'est plus considérécommevalide et l' ISED ne peut pas êtreutilisé sur le produit final. Danscescirconstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y comprisl'émetteur) etl'obtentiond'uneautorisationdistincte au Canada.
