WF-Q379-USA1Series IEEE 802.11a/b/g/n/ac 2T2R USB WiFi Module 特性 Features： 接收制式 Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac 芯片方案 Chip Solution Qualcomm 9379-7 结构大小 Size 18.0mm x 27.0mm x 3.0mm 型号预览 Model Overview： 型号 安装方式 WF-Q379-USA1 SMD 支持标准 IEEE 802.11a/b/g/n/ac 速率 频段 天线接口 备注 866.7Mbps 2.4G/5G 外置天线 3.3V 供电 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 客户确认反馈 Feedback of customer’s Confirmation 经确认，我方承认该规格书 We accept the specification after Confirmed 客户名称 Customer name 客户签字 Customer signature 确认日期 Confirmation Date 请签字后将此页与首页按以下地址回传我公司，谢谢！ Please feed back this paper and first paper after your signature by the address,thanks! 地址：四川省绵阳市安州工业园区 ADD： Anzhou,Industrial park,Mianyang,Sichuan 公司：四川爱联科技有限公司 Factory： Sichuan AI-Link Technology Co.,Ltd.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 更改记录 Record of Modification 序号 No 更改日期 Date of modification 主要更改内容 Main content of modification 1 2018/03/06 首次承认 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1. Introduction WF-Q379-USA1 module design is based on Qualcomm 9379-7 solution, The QCA9379-7 is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a 866.7Mbps PHY rate.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac 1.3 System Functions Table1: General Specification as below: Main Chipset Operating Frequency WiFi Standard Modulation Qualcomm QCA9379-7 2.4G/5G 802.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L x H): 18.0mm x 27.0mm x 3.0mm General tolerance: ±0.15mm 2.2 Pin definition TOP VIEW 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module Pin 1 2 3 Define NC NC NC Description NC NC NC Pin 17 18 19 Define NC GND WL_RF0 4 5 6 NC GND WL_USB_DP NC Ground WLAN USB2.0 DP Signal 20 21 22 GND GND WL_RF1 7 8 9 10 WL_USB_DM GND NC NC WLAN USB2.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0℃,+25℃,+40℃) and overall voltage (3.0V,3.3V,3.6V). 3. 1 IEEE 802.11g/a Section: Items Specification Mode Channel Data rate TX Characteristics 1. Power Levels 1) 16.5dBm Target (For Each antenna port) @ 11g/6Mbps~24Mbps 2) 16dBm Target (For Each antenna port) @ 11g 36Mbps 3) 15.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 5) 24Mbps (PER ≦10%) 6) 36Mbps (PER ≦10%) 7) 48Mbps (PER ≦10%) 8) 54Mbps (PER ≦10%) 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11g 2) IEEE802.11a - - -74 -70 -66 -65 dBm dBm dBm dBm -20 -30 - - dBm dBm 3.2 IEEE 802.11b Section: Items Contents Specification Mode Channel Data rate TX Characteristics 1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port) @1Mbps~11Mbps 2.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3.3 IEEE 802.11n HT20 Section: Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels 1) 16.5dBm Target (For Each antenna port) @ 2.4G/MCS0~MCS2 2) 16dBm Target (For Each antenna port) @ 2.4G/MCS3~MCS4 3) 15dBm Target (For Each antenna port) @ 2.4G/MCS5~MCS6 4) 14.5dBm Target (For Each antenna port) @ 2.4G/MCS7 5) 15.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 7) MCS6 (PER ≦10%) 8) MCS7 (PER ≦10%) 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G - - -65 -64 dBm dBm -20 -30 - - dBm dBm 3.4 IEEE 802.11n HT40 Section: Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels (Calibrated) 1) 15.5dBm Target (For Each antenna port) @ 2.4G/MCS0~MCS2 2) 15dBm Target (For Each antenna port) @ 2.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) 2) MCS1 (PER ≦10%) 3) MCS2 (PER ≦10%) 4) MCS3 (PER ≦10%) 5) MCS4 (PER ≦10%) 6) MCS5 (PER ≦10%) 7) MCS6 (PER ≦10%) 8) MCS7 (PER ≦10%) 6. Maximum Input Level(PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G - - -79 -76 -74 -71 -67 -63 -62 -61 dBm dBm dBm dBm dBm dBm dBm dBm -20 -30 - - dBm dBm 3.5 IEEE 802.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module @VHT80 MCS0~2 13) 13dBm Target (For Each antenna port) @VHT80 MCS3~5 14) 12.5dBm Target (For Each antenna port) @VHT80 MCS6 15) 11.5dBm Target (For Each antenna port) @VHT80 MCS7 16) 10.5dBm Target (For Each antenna port) @VHT80 MCS8 17) 9.5dBm Target (For Each antenna port) @VHT80 MCS9 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz /20MHz/30MHz 2) at fc +/-21MHz /40MHz/60MHz 3) at fc +/-41MHz /80MHz/120MHz 3.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 4. Software Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is QDART. 5. Antenna matching The BT RF ，ANT0 and ANT1 Pin connect to antenna, please refer to design demand a). 模块和天线要求远离干扰源，模块地和天线地要求为一个整体。 b). PIN12,PIN19和PIN22为模组的RF接口，与天线之间布线要求共面阻抗为50Ω，建议使用弧线和直线，长 度尽可能短。 c). L1, L2, C1组成π型匹配网络并靠近天线接口设计，具体根据天线推荐及排版设计的实测效果进行调整。 6.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 7. Packaging Information: 编带尺寸： 编带方向：（箭头代表编带走向） 包装示意图： 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 注：上图 3 个框示处为内盒标签粘贴位置。 注：红色箭头处为外箱标签粘贴位置。 标签样式： 内盒标签示例 外箱装箱清单标签示例 包装说明： 1. 产品放置方向、标签粘贴位置、包装按示意图进行； 2. 每卷放600只产品，每小盒放1卷，大箱共5装个小盒，产品数量共3000只/箱; 3. 外箱尺寸：378mm*297mm*370mm，小盒尺寸：355mm*355mm*50mm; 4. 真空包内放置2g干燥剂2袋，6色湿度卡1张; 5.其它按CVTE包装要求执行; 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules Part 15.247 and Part 15.407 2.3 Specific operational use conditions The module is limited to installation in mobile or fixed application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. 2.
modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. 2.10 Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for FCC Part 15.247&15.407 as listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
