INSTALLATION AND OWNER MANUAL MaglQtouch WIRELESS Smart Controller Original English Instructions
TABLE OF CONTENTS SAFETY Responsibilities Risk Assessment Warnings FCC Compliance 1 1 1 2 MOUNTING THE MAGIQTOUCH WIRELESS CONTROLLER Location 3 Mounting the Controller 4 MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER 7 Heater Installation 7 Heater With Zones 8 Cooler Installation 9 Mounting the Receiver 9 COMMISSIONING Connecting the Receiver 11 Pairing 11 Pairing Additional Controller WIRELESS CONNECTION MAINTENANCE Wireless RF Signal Range 13 15 18 CONTROLLER OR SYSTEM RESET 2X Controllers Connected 19
SAFETY This document provides technical guidance on the installation and operation of the MagIQtouch WI-FI smart app. what action(s) are necessary so the person doing the job does not injure themselves. EMPLOYER AND EMPLOYEE RESPONSIBILITIES • What are the chances of an incident happening? • What could the possible consequence be? • What can you do to reduce, or better still, completely get rid of the risk? Please read this manual carefully.
SAFETY FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
MOUNTING THE MAGIQTOUCH WIRELESS SMART CONTROLLER LOCATION The MagIQtouch Wireless Smart Controller should be placed approximately 1.5 metres/5’ above the floor, in the most used room of the home. Placement is critical for correct functioning of the temperature sensing thermostat inside the Controller. The following must be taken into consideration: • Avoid direct sunlight exposure. • Avoid mounting on external walls. • Avoid mounting the wall control near heat sources such as stoves and televisions.
MOUNTING THE MAGIQTOUCH WIRELESS SMART CONTROLLER MOUNTING THE CONTROLLER Remove the mounting bracket from the rear of the MagIQtouch Controller.
MOUNTING THE MAGIQTOUCH WIRELESS SMART CONTROLLER Step 4 Using the bracket as a template, mark the centre points for the screw and cable access holes.
MOUNTING THE MAGIQTOUCH WIRELESS SMART CONTROLLER Step 5 Insert wall plugs into holes. Align and screw the bracket into position using the supplied screws. ILL2937-A ILL2938-A Alternatively, a standard stud mounting bracket (used for wall plates) can be used with plasterboard walls.
MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER We recommend installation of the wireless receiver (Antenna) inside the ceiling space, as far away from heating/cooling appliances and ductwork as possible and also as close as practical to the area of the building the remote controller will be used the most. Therefore, we request that the antenna is always straightened and pointing towards the remote.
MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER HEATER WITH ZONES - INSTALLATION ILL2854-A MagIQtouch Controller INSTALLATION MANUAL | 8
MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER COOLER INSTALLATION ILL2855-A MOUNTING THE WIRELESS RECEIVER For most installations, mounting the receiver as shown (Fig 1) will provide satisfactory performance. 1 2 ILL665-D Using the communication cable supplied, connect it to the RJ socket as shown ILL670-E A. B. C.
MOUNTING THE MAGIQTOUCH WIRELESS RECEIVER For installations where the roof is framed with steel, resting the wireless receiver between joists and keeping the antenna as far away as possible and perpendicular (at right angles) to joists will give the best results. (Fig.
COMMISSIONING • Factors that may influence performance are: • Shielding from metal in the attic laying between the wireless receiver and the wireless smart controller. • Reflections from metal around the wireless receiver. • Interference from nearby transmitters (e.g. mobile phone, AM radio, Television, RF security systems) CONNECTING THE WIRELESS RECEIVER Please refer to the installation manual of the heating or cooling appliances for connecting the 6 pin communication plug from the wireless receiver.
COMMISSIONING Step 3 Within 8 minutes of cycling the power, press the home button on the Wireless Smart Controller to activate it. ILL1521-C Step 4 Follow the on screen instructions to pair the wall control.
COMMISSIONING Step 5 When the Wireless wall controller is paired the installation wizard will appear. The Installation wizard will step you through the complete process. ILL1610-B To complete the commissioning please refer to the ‘MagIQtouch Controller Installation manual supplied with this kit. PAIRING ADDITIONAL WIRELESS CONTROLLER The wireless receiver can communicate with 2x Wireless Smart Controllers within the system.
COMMISSIONING Step 2 Cycle the power to the installation. This will make the Wireless receiver discoverable for a maxmium of 8 minutes to the Wireless smart controller. Step 3 Select ‘Additional Controller’ to pair the second Wireless controller. ILL2859-B ILL2860-A The additional wireless smart controller is now ready to use.
WIRELESS CONNECTION MAINTENANCE Should the wireless communications require updates or modifications in the system, these can be accessed in the SERVICE section of the Wireless Smart controllers as follows; Step 1 ILL1613-D Step 2 ILL1623-D 15 |
WIRELESS CONNECTION MAINTENANCE Step 3 ILL2862-A Step 4 Refer to MagIQtouch Wall control install manual for code.
WIRELESS CONNECTION MAINTENANCE ILL2863-A ABOUT WIRELESS RECEIVER Detailed RF signal strength (RSSI) and battery voltage (mV) information is displayed here. CHECK/MODIFY WIRELESS CONFIGURATION All known Wireless smart devices connected to the system will be shown. If devices are missing the wireless receiver can re-scan for wireless devices from this configuration screen to maintain the system.
WIRELESS CONNECTION MAINTENANCE WIRELESS RF SIGNAL RANGE It is recommended to check the RF range of the wireless smart controller during commissioning to know the best positions / environments to maintain normal operation of the system & controller.
CONTROLLER OR SYSTEM RESET It is possible to reset the whole system (including all connected components) or the MagIQtouch Controller only. Use a pin or paperclip to press and hold the reset button located at the back. ILL1596-C This will cause the following screen to appear: ILL1632-A Note! RESET WALL CONTROLLER ONLY This option should only be selected if the wall controller connected was previously used in another installation.
CONTROLLER OR SYSTEM RESET SYSTEM RESET WHEN 2X WIRELESS WALL CONTROLLERS ARE CONNECTED Recommended sequence to reset the whole system when 2x wireless wall controllers are installed.
CONTROLLER OR SYSTEM RESET SYSTEM RESET WHEN 2X WIRELESS WALL CONTROLLERS ARE CONNECTED Step 4 ILL3037-A Step 5 When the screen shot below is displayed, go to the 2nd wireless wall controller ILL2857-A Step 6 Activate the 2nd wireless wall controller 21 | ILL2879-A
CONTROLLER OR SYSTEM RESET SYSTEM RESET WHEN 2X WIRELESS WALL CONTROLLERS ARE CONNECTED Step 7 ILL3038-A Step 8 ILL3039-A Step 9 Pair controller and the Installation Wizard will begin.
SUPPORT Symptom Cause Action The MagIQtouch Wireless Smart Controller has no display Batteries not fitted Remove battery cover and fit 4x AA batteries Batteries not fitted correctly Ensure batteries are orientated as shown inside battery cavity Batterries are low Replace 4x AA batteries Controller in sleep mode Press the Home button to the right of the screen The MagItouch Wireless Smart Controller states ‘This Controller has lost Communication!’ Wireless Smart Controller out of range Check RF
SUPPORT Symptom Cause Action The screen on the Wireless Smart Controller goes blank after a while The Smart controller conserves the battery life by putting the controller in a sleep mode Press Home Button The screen on the wireless Smart controller goes blank but the system still operates The Smart controller conserves the battery life by putting the controller in a sleep mode To check the status of the system press the ‘HOME’ button to the right of the Wireless smart controller to see the current
USER GUIDE 25 |
USER GUIDE ILL1582-C Hello and congratulations on purchasing a MagIQtouch Wireless Smart Controller for your home! The MagIQtouch Wireless Smart Controller is a versatile and intelligent Controller that can be used with a range of compatible products. This manual is a supplement to the MagIQtouch Controller Owners Manual supplied with this Wireless controller. For more information about operating the MagIQtouch Wireless Smart Controller, please refer to the other Owners Manual supplied.
GENERAL TIPS • Mount the MagIQtouch Wireless Smart Controller in a room you want climate controlled. Ideally it should be positioned 1.5m (5’) from the floor and away from any other heating or cooling sources. • Ensure the MagIQtouch Wireless Smart Controller is not exposed to direct sunlight as this will impact the temperature reading. • Avoid blocking or restricting the vent holes located in the side of the MagIQtouch Controller, as this is where the thermostat is located.
QUICK START Here’s a brief visual guide to get you started quickly! Turning on the MagIQtouch Wireless Smart Controller. STEP 1 Activate screen.
SLEEP MODE If the Wireless controller is not touched for a period of time, it will go to a sleep mode where the screen will go blank. Simply push the “home” button to view the display.
WIRELESS RANGE It is recommended for optimum performance to operate your Wireless Smart Controller within 30m of the appliance.
WIRELESS RANGE To check the signal strength of your Wireless Smart Controller, follow these steps.
WIRELESS RANGE As you move the wireless controller around your home it will be quite normal for the RF signal strength to change. If the wireless control is out of range the following message will be displayed.
ADDITIONAL WIRELESS SMART CONTROLLER If you have an additional Wireless Smart Controller installed in your system both controllers have the same operation and features. The last controller used is the active controller Wireless Controller No. 1 “ACTIVE” ILL1544-D Wireless Controller No.
ADDITIONAL WIRELESS SMART CONTROLLER To activate an ‘INACTIVE’ wall control press ‘ACTIVATE’ ILL1544-C The “Activate” button is displayed on the Inactive controller.
TROUBLE SHOOTING Your MagIQtouch Controller may prompt you to call a service agent to resolve a service issue. If your Controller has only recently been installed, we recommend you call your local Dealer for support first. Otherwise, call the Service number on the back of this manual. Symptom Cause Action The MagIQtouch Controller has no display. Batteries not fitted Remove battery cover and fit 4x AA batteries. NOTE: Rechargeable batteries should not be used.
Warranty Service Australia 1-300-650-644 Technical Support Australia 1-300-650-399 For regions outside Australia: Contact your local Dealer seeleyinternational.com MANUFACTURED BY: SEELEY INTERNATIONAL PTY LTD 112 O’SULLIVAN BEACH RD, LONSDALE SA, 5160.