ST-IP4FB QUICK START GUIDE www.nacebrands.com www.securitytronix.
ST-IP4FB·Quick Start Guide About this Manual This Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version at www.securitytronix.com Please use this user manual under the guidance of professionals.
ST-IP4FB·Quick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ST-IP4FB·Quick Start Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
ST-IP4FB·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
ST-IP4FB·Quick Start Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
ST-IP4FB·Quick Start Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use. ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture.
ST-IP4FB·Quick Start Guide Table of Contents 1 Appearance Description ................................................................. 8 1.1 Overview of Type I Bullet Camera ................................... 8 1.2 Overview of Type II Bullet Camera ................................ 10 1.2.1 Resetting the Camera ......................................... 11 1.2.2 Setting the WPS Protocol.................................... 12 1.3 Overview of Type III Bullet Camera ...............................
ST-IP4FB·Quick Start Guide 1 Appearance Description 1.
ST-IP4FB·Quick Start Guide Table 1-1 Description No. Description No. Description 1 Mounting Base 4 Lens 2 Back Case 5 Sun Shield 3 Front Case 6 Power Cable 7 Reset Button 8 GND Screw 9 10/100M Self-adaptive Ethernet Interface Type I camera does not support the function of Wi-Fi or SD card. Press Reset button about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
ST-IP4FB·Quick Start Guide 1.
ST-IP4FB·Quick Start Guide Table 1-2 Description No. Description No. Description 1 Mounting Base 7 Memory Card Slot 2 Back Case 8 Power Supply Interface 3 Sun Shield 9 10/100M Self-adaptive Ethernet Interface 4 Lens 10 PoE Cable 5 Adjusting Nut 11 GND Screw 6 WPS/RESET Button This type of bullet camera supports PoE power supply. You can power the camera by connecting both DC 12V interface and the Ethernet interface. Or you can connect the Ethernet interface only.
ST-IP4FB·Quick Start Guide WPS/RESET Figure 1-3 WPS/RESET Button 1.2.2 Setting the WPS Protocol A wireless router with the WPS function is required to enable the WPS function of the camera. Refer the steps below. Steps: 1. Enable the WPS function of your router. Refer to the operation guide of your router for detailed procedures. 2. Press the WPS/RESET button (about 2s) on the camera to join in the wireless network.
ST-IP4FB·Quick Start Guide WPS/RESET Figure 1-4 WPS/RESET Button You can also press the WPS button on the camera first and then enable the WPS function on the router to establish the connection. But the WPS function of the router must be turned on within 120s right after pressing the WPS/RESET button on the camera.
ST-IP4FB·Quick Start Guide 1.
ST-IP4FB·Quick Start Guide Table 1-3 Description No. Description No. Description 1 Mounting Base 6 Grounding Screw 2 Back Case 7 10/100M Self-adaptive Ethernet Interface (PoE) 3 Front Case 8 Power Supply (DC 12V) 4 Lens 9 Memory Card Slot 5 Sun Shield 10 Reset Button This type of bullet camera supports PoE power supply. You can power the camera by connecting both DC 12V interface and the Ethernet interface. Or you can connect the Ethernet interface only.
ST-IP4FB·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
ST-IP4FB·Quick Start Guide 2.1 Installation of Memory Card Type II and Type III camera support memory card function. Follow the steps to mount and unmount a memory card. Steps: 1. Unscrew the cover on back case to expose memory card slot. Cover Figure 2-1 Unscrew the Cover 2. Insert the memory card into the memory card slot.
ST-IP4FB·Quick Start Guide 3. (Optional)To unmount the memory card, push to get it ejected. 4. Screw the cover back to the camera. 2.2 Installation of the Bullet Camera Both wall mounting and ceiling mounting are suitable for the bullet camera. Wall mounting will be taken as an example in this section. You can take steps of wall mounting as a reference if ceiling mounting is adopted. Steps: 1. Drill the screw holes in the wall according to the drill template.
ST-IP4FB·Quick Start Guide 2. Route the corresponding cables. 3. Secure the camera to the wall with the supplied Screws. Figure 2-4 Secure the Camera to the Ceiling 4. Connect the cables and power on the camera to view live view image. 5. Adjust the surveillance angle.
ST-IP4FB·Quick Start Guide 1). Loosen the adjusting nut. 2). Adjust the pan direction [0° to 360°]. 3). Adjust the tilt direction [0° to 90°]. 4). Rotate the camera [0° to 360°] to adjust the lens to the surveillance angle. 5). Tighten the adjusting nut to complete the installation. 2.3 Installation of Network Cable Water-proof Jacket (Optional) Purpose: If the camera is installed outdoor, you can adapt the water-proof accessory for the network cable after the camera is secured on the installation surface.
ST-IP4FB·Quick Start Guide No. Components 3 Network Plug 4 Waterproof Endcap 5 Waterproof Rubber Gasket 6 Lock Nut 7 Network Cable from Router/Switch Align the snap and notch. i. Insert ⑤ into ④. ii. Secure ⑥ with ④.
ST-IP4FB·Quick Start Guide Steps: 1. Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤ (rubber gasket inset ridge must face waterproof endcap), and the water-proof endcap ④ in order. 2. Crimp an RJ-45 network plug ③onto the end of the cable, taking care to insert the twisted pairs of wires in correct order. 3. Place the O-type gasket ② onto the end of the camera’s network interface socket ①. 4. Insert the network plug ③ into the camera’s network interface socket①. 5.
ST-IP4FB·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. 3.1 Wiring Connect the camera to network according to the following figures.
ST-IP4FB·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Note: Refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
ST-IP4FB·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
ST-IP4FB·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2. Check the device status from the device list, and select the inactive device. Select inactive device. Input and confirm password.
ST-IP4FB·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
ST-IP4FB·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an activate device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.
ST-IP4FB·Quick Start Guide Note: You can enable the STGO2 service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Please refer to the User Manual of SADP for details.
ST-IP4FB·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
ST-IP4FB·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in. Figure 4-2 Download Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4 to login.
ST-IP4FB·Quick Start Guide 5 Operating via Guarding Vision/STGO2 Purpose: STGO2 is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: STGO2 service is not supported by certain camera models. 5.1Enable STGO2 Service on Camera Purpose: STGO2 service should be enabled on your camera before using the service. You can enable the service through SADP software or web browser. 5.1.1 Enable STGO2 Service via SADP Software Steps: 1.
ST-IP4FB·Quick Start Guide Service” “Privacy Policy” Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to STGO2 app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable STGO2 Service via Web Browser Before you start: You need to activate the camera before enabling the service. Refer to Chapter 3.2.
ST-IP4FB·Quick Start Guide Steps: 1. Access the camera through web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Guarding Vision dev.guardingvision.com Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Guarding Vision. 4. Check the checkbox of Enable. 5. Click and read "Terms of Service" and "Privacy Policy" in pop-up window. 6.
ST-IP4FB·Quick Start Guide 5.2 STGO2 Setup Steps: 1. Download and install the STGO2 app by searching TM “STGO2” in App Store or Google Play . 2. Launch the app and register for a STGO2 user account. 3. Log in STGO2 app after registration. 5.3 Adding Camera to STGO2 Before you start: You need to enable the STGO2 service on camera before adding it to your STGO2 account. Refer to Chapter 5.1. Steps: 1. Use a network cable to connect the camera with a router if the camera does not support Wi-Fi.
ST-IP4FB·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number. 3. Input the verification code of your camera. Note: ● The required verification code is the code you create or change when you enabling STGO2 service on camera.
ST-IP4FB·Quick Start Guide 5.4 Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection. If there are any questions, or requests, please contact our support department at 1-800-688-9282.
SECURITYTRONIX 2-Year Limited Fixed Camera Warranty Securitytronix. (the "Company") warrants to the Original Purchaser that the Fixed Camera is free from defects in workmanship or material under normal use. This warranty starts on the date of shipment of the hardware to the Original Purchaser. During the warranty period, the Company agrees to repair or replace, at its sole option, without charge to Original Purchaser, any defective component in the Fixed Camera.
