INSTRUCTION MANUAL ST-F35TEST CCTV Test Meter
SAFETY INFORMATION The ST-‐F35TEST is intended for use in compliance with the local regulations for electrical equipment. The user is not to use the ST-‐F35TEST in environments or applications for which it is not intended. To prevent damage or failure the ST-‐F35TEST must not be exposed to water or moisture.
PACKAGE CONTENTS This package contains: One ST-‐F35TEST meter One LAN cable tester One 5V 2A power supply One lithium ion polymer battery One BNC cable One RS485 cable One safety cord One case One instruction manual PRODUCT DESCRIPTION The ST-‐F35TEST has been developed for the on-‐site installation and
FRONT PANEL 1 Power Indicator: Lights green while powered on. 2 Data-‐Reception Indicator: Lights red while the data is being received. 3 Data-‐Transmission Indicator: Lights red while the data is being transmitted. 4 Charge Indicator: Lights red while the battery is being charged.
7 Sub-‐Menu: Shows and sets the values of functions. 8 Press for more than 2 seconds to turn on/off the tester. Press for less than 2 seconds to turn on/off the PTZ controller menu displaying. Menu Key: Pops up the main-‐menu; constant-‐press MODE or press the key can shift between functions.
SIDE and TOP VIEWS 22 Resets the default parameter settings. 23 External Power Supply (DC, 5V): Use the included power adapter. 24 UTP Cable Port: Use with the UTP LAN cable tester. 25 RS232 Interface: RS232 communication for the PTZ. 26 Audio Input: Test audio on the front end.
BATTERY INSTALLATION The ST-‐F35TEST has a built-‐in lithium ion polymer rechargeable battery. The battery cable inside battery cabin should be disconnected for safety during transportation! Prior to using the ST-‐F35TEST, the battery cables inside the battery cabin should be securely connected.
OPERATION POWER ON Continuously press the POWER key (at least 2 seconds) to power on / off the ST-‐F35TEST. When powered on, press the MODE key and the main menu will appear.
2. Video Setting Adjust the LCD brightness, contrast, color saturation, video format and video level testing. 3. Colorbar Generator Output or receive seven different forms of video colorbar to tester monitor, cable or other equipment. 4. Cable Tester Test LAN cable or telephone cable.
PTZ CONTROLLER Display the input video images. Has pan/tilt the P/T unit and zoom in/ out the image capability. Setup the controlling parameters (e.g., protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position).
Press the POWER key for a full-‐screen image. A. Protocol: Select the protocol according to the PTC camera. Up to 21 popular protocols are available (e.g., Pelco P, Pelco D, Samsung, Yaan, LiLin, CSR600, etc.). B. Port: Select the communications port for the PTZ camera (RS232, RS422, RS485). C.
OSD Menu of Dome (for reference only) MAIN MENU MAIN MENU 1. DISPLAY SETUP 1. Display configuration 2. CAMERA SETUP 2. Set camera parameters. 3. CONTROL SETUP 3. Set PTZ controlling 4. CAMERA MASK SET 4. Set privacy mask 5. PROGRAM 5. Set auto-‐running functions 6. PAL CAMERA 6. PAL/NTSC Switch 7.
VIDEO SETTING User can customize the brightness, contrast and saturation of the LCD according to the environment and display the format (PAL/NTSC) of video input. a. Press the or key to select the parameter for which you want to change the value. b. Press the or key to change the value.
CABLE TESTER Test LAN cable or telephone cable. Connect LAN cable or telephone cable to the ST-‐F35TEST and cable tester. The connecting status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable tester kit.
DATA MONITOR Data Monitor captures the command data from the RS485 controlling system. a. Connect the RS485 or RS232 interface of the controlling system with the ST-‐ F35TEST’s RS485 or RS232 ports. In the case of RS485, A to A, B to B. b.
PTZ ADDRESS SCANNING Device Setting allows the ID search of the PTZ camera. Note the PTZ camera to be searched must be isolated from other PTZ cameras before beginning the search. Not doing so will cause all PTZ cameras in the same system to pan at the same time. a.
DC12V 1A POWER OUTPUT A camera can be powered with DC12V 1A power from the ST-‐F35TEST. Do not input any power to the ST-‐F35TEST’s DC12/1A OUTPUT port. Doing so will destroy the unit. Do not output this DC12/1A power to the ST-‐F35TEST’s power port. Doing so will destroy the unit.
SPECIFICATIONS MODEL ST-‐F35TEST Video Test Signal Mode: NTSC/PAL (Auto adapt) Display: 3.5 inch digital TFT-‐LCD ,960 x 240 resolution LCD Adjustment: Brightness, Contrast, Saturation adjustable Video IN/OUT: 1 channel BNC Input & 1 channel Output Video Output Mode 1.
Battery: Built-‐in 3.7V Lithium polymer battery, 3000mAh Rechargeable: After charging 3-‐4 hour, working time lasts 12 hours Low Consumption: Energy saving technology General Working Temperature: -‐22°F to +158°F Working Humidity: 30%-‐90% Dimension/Weight: 7”x 3.7” x 1.4”/ 0.75lb.
