USER MANUAL ST-PTZ-RC Infrared Remote PTZ Controller v1.
PACKAGE CONTENTS This package contains: One ST-PTZ-RC handheld infrared remote controller One PT Dome Controller One connection block One user manual Note: The ST-PTZ-RC handheld infrared remote controller requires 2 AAA batteries (not supplied). The PT Dome Controller requires a 12VDC 1A power supply (not supplied) such as the Securitytronix ST-PS12VDC1A. PRODUCT DESCRIPTION The ST-PTZ-RC is a consumer grade pan, tilt, zoom (PTZ) controller designed for PTZ dome cameras.
INSTALLATION AND OPERATION 1. UNPACKING and HANDLING Each unit is shipped assembled and factory tested. Ensure that all accessories are removed from the container before discarding packing material 2. MECHANICAL INSPECTION Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is clean, and no connectors are broken, damaged, or loose. If equipment appears to be damaged or defective please contact your distributor or Securitytronix at 1-610-429-1511 for assistance. 3.
5. WIRING CONNECTIONS a. Per the diagram below, connect an unshielded twisted pair (UTP) control cable between the PTZ dome camera and the PT Dome Controller using the PT Dome Controller’s connection block. Be sure the connection polarities at the camera and the PT Dome Controller are the same. b. Connect a 12VDC 1A power supply to the PT Dome Controller’s power port. c. After the PT Dome Controller is powered on the unit will display A001 P001 or A refers to “address” so A001 = address 1.
A- - - A- 26 d. Within any mode you can press the ESC button and the system will return you to the address mode. e. If you only want to change an address number below 10, you only need to press the appropriate numeric key one time. Set Preset Position a. Using the Infrared Remote Controller’s LEFT/RIGHT, UP/DOWN buttons move the camera to a location for the Preset Position. b. Press the PRSET button and hold for 3 seconds. The PT Dome Controller will display “SET”.
Set HOME Position a. Setting the HOME position is very similar to setting Preset Positions. b. Using the LEFT/RIGHT and UP/DOWN buttons move the camera to the desired Home Position. c. Press PRESET and hold for 3 seconds. d. Press HOME followed by ENTER to confirm. Set A and B Limiting Positions a. Setting the A and B Limiting Positions is very similar setting Preset Positions and the HOME position. b. Using the LEFT/RIGHT and UP/DOWN buttons move the camera to the desired A Position. c.
f. To run a Pattern Tour press RUN and the PT Dome Controller’s will display g. Press RUN again to stop the Pattern Tour. PrUN Setting Camera Speed a. For camera travel time (i.e., camera rotation from one Preset Position to another either manually or by running Pattern Tour) four separate speed settings are available: S1 = 8, S2 = 40, S3 = 51 and S4 = 63 S1 is the slowest and S4 is the fastest b. Speed can be set by pressing SPEED then S1, S2, S3 or S4 and ENTER c.
The SHOT button calls the desired Preset Position. HOME is for a Home Preset Position. A and B are Preset Positions that can serve as Left and Right Limiting Positions allowing the camera to automatically scan between the two positions. The PRESET button is to set a preset point. The DELETE button is to clear a preset point. Each of these keys needs to be pressed and held for 3 seconds to achieve the desired function. Pressing AUTO puts the system into auto cruise mode.
Pressing DISP displays the system’s software version. Pressing SETUP allows the configuring of the ST-PTZ-RC’s protocol and baud rate. 7. TROUBLESHOOTING TIPS a. The ST-PTZ-RC is not controlling the camera at all – (i) be sure the R485 connections between the ST-PTZ-RC and the camera are using the same polarities; (ii) check to see if the correct baud rate has been set with the camera; (iii) check to see if the correct protocol has been with the camera. b.