Installation Instructions

ManualsBrandsSecurity Brands ManualsElectronics433-MHz Receiver

QUICK START GUIDE

1 of 6

Make sure you have all items shown here. (Screwdriver not shown)

START HERE

Keypad Unit Receiver 9-V Battery Key Carriage Bolt

( 4x )

Hex Nut

( 4x )

What’s what?

Important components labeled

Receiver

Shown with cover removed.

Internal wiring not shown for clarity.

Keypad Unit

Back of front panel shown.

Internal wiring not shown for clarity.

9-V Battery

Must be installed before use

Connection Terminals

For wiring to compatible

AC/DC power source and

gate operator or door opener

Relay Status LED

Indicates whether relay is

active or inactive

(Relay is active when lit)

Programming Button

For pairing receiver to keypad

Reset Button

For performing reset procedures

on keypad

Power LED

Indicates whether or not unit has power

Programming LED

Indicates status of pairing process

Hole Plug

Model

Adhesive

Mounting Pad

Carefully unpack box.

14-REC20

Summary of content (7 pages)

PAGE 1
of 6 QUICK START G U I D E Model 14-REC20 1 Carefully unpack box. 2 Make sure you have all items shown here.
PAGE 2
of 6 QUICK START G U I D E 3 Unlock and remove front panel of keypad unit; then using included carriage bolts and hex nuts, attach unit to pedestal as shown. Model 14-REC20 C A U T IO N ! Using Tek screws, zip ties, or included adhesive mounting pad, attach receiver to inside wall or other surface of gate operator. 4 The receiver is not weatherproof and must be mounted inside a weatherproof enclosure. Internal components can be damaged if exposed to the elements.
PAGE 3
of 6 QUICK START G U I D E Model 14-REC20 6a Remove receiver cover; then hold down Programming button on circuit board for 3 seconds and let go. 6b Pair keypad unit with receiver by entering sequence below on keypad.(Make sure 9-V battery is connected on keypad unit) 1 LED will light solid orange 2 5 1 Master Code (can be changed) 9 6c While pairing, keypad unit will beep and flash Once receiver LED goes out and “good” tone is heard on keypad unit, pairing is complete.
PAGE 4
of 6 QUICK START G U I D E Model 14-REC20 A2 Additional programming (continued) Change Master Code 1 2 5 1 Current Master Code (1251 is default) Delete All Codes (Cannot Be Undone) 3 Sub Mode ? ? ? ? 1 New Master Code 2 5 1 5 Sub Mode Master Code 5 1 8 Sub Mode Master Code (can be changed) ? ? Channel ? ? ? ? ? 1 Latch Code (1 for A, 2 for B) ? 5 1 Master Code (can be changed) 7 1 2 5 Keypad unit will beep and flash while erasing memory then sound “good” tone
PAGE 5
QUICK START G U I D E 1 Add Access Code(s) to Channel A 8 Add One-Time-Use Code ( Channel A) 2 Delete Code(s) 9 Pairing and Setting Keypad ID Change Master Code 4 Configure “Three Strikes, You’re Out” 5 Add Latch Code 6 Set Relay Output Time 7 Add Access Code(s) to Channel B 0 Things to Know The Star Key (*) The star key deletes your current entry. If you happen to make a mistake keying in a code, simply press the star key to delete the entire entry and start over.
PAGE 6
of 6 QUICK START G U I D E Model 14-REC20 Notes Ridge 2.0 14-500 NEED HELP © 2020 Security Brands, Inc. All rights reserved. Call (972) 474-6390 Email techsupport@securitybrandsinc.com We are available Mon–Fri / 8am–5pm Central QSG-14500-EN Rev.
PAGE 7
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.