User Guide RTLS Staff Safety Badge A2145091x Please contact your Distributor / Installer for service … Tel.: ___________________________ 39 Chenell Drive Concord, NH USA 03301-8501 Phone: (800) 451-7917 / (603) 223-0745 Fax: (603) 227-0200 http://www.securecare.com © 2016 Secure Care Products®, LLC CONTENT IS SUBJECT TO CHANGE WITHOUT NOTICE FOR THE LATEST UPDATED MANUALS PLEASE VISIT AND LOG INTO THE DISTRIBUTOR PORTAL AT WWW.SECURECARE.COM DOC. No.: A21450690 Rev.
TABLE OF CONTENTS SECTION 1 IMPORTANT NOTICES 4 PLEASE READ THIS MANUAL BEFORE BEGINNING THE INSTALLATION OF A SECURE CARE SYSTEM 4 Introduction 7 The Risk 7 Minimizing the Risk 7 LIMITATION 8 DESCRIPTION 9 ADVISORY 9 ACKNOWLEDGEMENT 9 SECTION 4 STAFF SAFETY BADGE DESCRIPTION AND SPECIFICATIONS 10 Overview 10 Specifications: 10 SECTION 5 OPERATING INSTRUCTIONS Adding a Tag to ENvisionIT 11 11 SECTION 6 PURCHASING STAFF SAFETY BADGES 13 Lanyard Application 13 Belt Clip Application
2. Limited Warranty 18 3. Limitations of Liability 19 4. Governing Law and Arbitration 19 5. Severability 20 6. Waiver 20 APPENDIX A DAILY STAFF SAFETY BADGE TESTING LOG DOC. No.: A21450690 Rev.
SECTION 1 IMPORTANT NOTICES PLEASE READ THIS MANUAL BEFORE BEGINNING THE INSTALLATION OF A SECURE CARE SYSTEM This installation manual is provided for reference by purchasers and installers of Secure Care Products, LLC (“Secure Care’s”) systems.
MARK OR TRADE NAME USED OR CLAIMED BY SECURE CARE OR FROM THE DELIVERY OR INSTALLATION OF THE HARDWARE WITH SECURE CARE SOFTWARE, PARTS AND/OR PRODUCTS OR FROM A COURSE OF DEALING OR USAGE IN TRADE.
established by Secure Care is required. Regardless of how Secure Care’s software, parts or products are obtained, they should not be installed, set-up, tested, supported, maintained or repaired by any person who has not satisfactorily completed that technical training (a “qualified service technician”.
SECTION 2 ADVISORY NOTICE Introduction The Staff Safety Badge solution enables tracking and location of critical staff members in real time. The Staff Safety Badge button allows staff members to alert a nurse station and provides info on location requesting attention. The Staff Safety Badge works with the ENVisionIT software in the RTLS system. The software can respond to specific button presses with customizable responses.
The administrators should: EXPLAIN and ensure all authorized personnel using the Staff Pendant are fully familiar with the use and application of the Secure Care system used by the facility. Provide and EXPLAIN the “Staff Safety Badge User Guide” to each of the authorized personnel. TRAIN each of the authorized personnel in the use of Staff Safety Badge and its safekeeping while not in use, including record keeping requirements and replacement requirements.
SECTION 3 ADVISORY NOTICE ACKNOWLEDGEMENT DESCRIPTION The Secure Care Products STAFF SAFETY BADGE (the “STAFF SAFETY BADGE”) is an optional feature of the Secure Care RTLS Asset tracking and Resident Tracking System (the “System”) that provides an easy way for authorized personnel track staff movements throughout the facility or alert other staff members to an area or resident in need of attention.
SECTION 4 STAFF SAFETY BADGE DESCRIPTION AND SPECIFICATIONS Overview The Badge has a configurable button that when pressed will send a unique transmission that could be configured in the software to be a panic alarm, staff duress, etc. The badge will be used to alert the system as to the location/assistance to the staff member in the full RTLS system if the button is pressed. The Staff Safety Badge is housed in a thin ID-card style enclosure with button.
SECTION 5 OPERATING INSTRUCTIONS Adding a Tag to ENvisionIT 1. 2. 3. Log in to ENvisionIT Software with your respective User Name and Password. Click on the MENU tab on the left side of the window. Click on “TAG LIST” and fill out all of the required information following local policies. Figure 2 - Selecting the Tag list Doc. No.: A21450690 Rev.
4. Click on the “New Tag” button and fill out the information for the new tag. Figure 3 - New Tag Screen 5. Click the “Save” button. Now the Tag can be added to the rules list and configured as needed. Refer to the ENVisionIT Users Guide for more detailed information. DOC. No.: A21450690 Rev.
SECTION 6 PURCHASING STAFF SAFETY BADGES Lanyard Application Locate the small metal clip on one end of the lanyard. Attach the clip to the badge. Adjust the lanyard loop and hang around your neck. Belt Clip Application Remove adhesive backing from belt clip unit and press firmly against the engraved side of the badge. Squeeze clip and apply to belt or pocket. New Staff Safety Badges Staff Safety Badges are purchased directly from Secure Care Products. Please call (800) 451-7917 to order new units.
SECTION 7 TESTING THE STAFF SAFETY BADGE To test the Staff Safety Badge, verify the tag is seen by the system and responds appropriately to the number of button presses. Doc. No.: A21450690 Rev.
SECTION 8 COMPLIANCE INFORMATION FCC Notice (For U.S. Customers) This device complies with Part 15 of the FCC Rules: Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 3. This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties.
SECTION 9 GENERAL PRODUCT WARRANTY STATEMENT INFORMATION BY PERMITTING INSTALLATION OR BY MAKING USE OF ANY PRODUCT OR SERVICE DESIGNED OR MANUFACTURED BY SECURE CARE PRODUCTS, LLC.
HARDWARE AND/OR ITS USE WITH OR OPERATION IN THE SECURE CARE SYSTEM THAT MIGHT OTHERWISE ARISE OR BE IMPLIED FROM THE FACT THAT SUCH HARDWARE CARRIES SECURE CARE’S LOGO OR NAME OR ANY OTHER TRADEMARK, SERVICE MARK OR TRADE NAME USED OR CLAIMED BY SECURE CARE OR FROM THE DELIVERY OR INSTALLATION OF THE HARDWARE WITH SECURE CARE SOFTWARE, PARTS AND/OR PRODUCTS OR FROM A COURSE OF DEALING OR USAGE IN TRADE.
G. It is important that any installation, set-up, testing, support, operation, maintenance, repair or use involving the system comply with all local and national electrical and life safety codes. If you have any questions about compliance with those codes, please contact your local authorities. H.
NOTE: Transmitters are not repaired, nor is the warranty extended, beyond the expiration date. If this Product is returned to Secure Care for any reason, you will retain title (unless and until a part or product is replaced, in which case you will obtain title to the replacement part or product at the time of replacement), the risk of loss, and the obligation to pay all costs of shipping, storage and other charges and obligations relating to this Product. C.
in accordance with the commercial arbitration rules of the American Arbitration Association, in Concord, New Hampshire. The decision of the arbitrator shall be binding and enforceable by any state or federal court in New Hampshire, and you hereby consent to the personal jurisdiction of any state or federal court in New Hampshire for that purpose.
APPENDIX A DAILY STAFF SAFETY BADGE TESTING LOG Date Badge ID # Badge Test Pass/Fail Badge Expiration Date Comments Doc. No.: A21450690 Rev.
NOTES: DOC. No.: A21450690 Rev.
