Quick Start Guide

Quick Start Guide
WIFIGPS/GlonassLTE BLE
Getting to know your device
Lanyard hole
Microphone
SOS button
Call button
Silent mode
button
Charging contacts
LED light
LED light
Screw holes
SOS button
Charging contacts
Put the SIM card
The SIM card is not included in the package.
A Nano SIM card is available from the user's local
operator.
Unscrew the back cover and remove.
Insert the SIM card and make sure it’s activated
with credits.
Put the cover back and tighten the screws.
Before installing the SIM card, check if the SIM
card has PIN code or not, if yes, please use a
cell-phone to remove the card's PIN code.
TIP
TIP
TIP
Charging your device
There are two ways to charge your device.
For the first time use, please fully charge the
battery for around 2~3 hours.
TIP
When the battery level falls below 20% it will
send a low battery warning message to people
on the contact list via text message or APP.
TIP
The charging base light will glow when charging
and turn solid when fully charged.
Place the device on the charging base.
Connect the USB cable from charging base to
the AC adaptor.
1/ charging base
Switching on and off device
To turn on the device:
press the CALL button for 1
second, all the LEDs will flash rapidly. The
device can also be turned on automatically by
charging via magnetic USB cable or put it into
the docking station.
To turn off the device:
press and hold the side
button and SOS button together for 3 seconds
until the LEDs turn off.
1sec.
3sec.
What do the lights mean?
Green
Means
Light shows a single
flash rapidly every 3
seconds
Light shows a double
flash rapidly every 3
seconds
The device has a
stable
cellular signal
The device is
registered to the
cellular network
Light shows a
single flash rapidly
every 3 seconds
The device has no
latest location fix
Light shows
a double
flash rapidly
every 3
seconds
Light Off
The device
has latest
location fix
The device
is not
fixing the
latest
location
Red ON (solid)
Device has been
fully charged
Red shows a double
flash rapidly every 3
seconds
BLE connected
Red Blinking Quickly
Red Off or blinking
slowly
Battery power is
lower than 20%
The device is
charging
Cellular signal indicator--Green
Power indicator--Red
Positioning indicator--Blue
Red
Blue
Means
State
Red
State
Activating an SOS Alarm
When you need help, press the SOS button for
3-4 seconds till you hear a voice prompt of
activating an SOS alarm. This starts the
sequence of “help me!” text message send to
your emergency contact numbers followed by
the outgoing calls.
（Press for 3-4 seconds）
If the device fails to connect to the first number,
it will call the second number after delay of 10
seconds. In case the second number fails to be
connected as well, the system will connect to
the third number etc.
3-4sec.
Between each call, it will have 10 seconds
delay, during this time, user can stop call
sequence or prevent a possible false alarm by
pressing the SOS button. The receiver of the call
can also stop call sequence by pressing 1 on
their mobile phone during two way talking.
Use the side buttons +/- to adjust the sound
volume during a call.
Please remember to program emergency
contact numbers. It is not mandatory for all ten
authorized numbers to be set, however a
minimum of one must always be set.
Please be patient during the call sequence.
There can be short delays as the alarm calls
phones who maybe out of range or delivered to
people’s voicemail.
Getting a GPS fix
To get an initial fix for the GPS features, use
outdoors or near a window so the device can
get a fix on the satellites. This could take few
minutes according to your environment.
GPS
Making a Phone Call
To make a call, press side call button for 3
seconds and you will hear a beep, and then it
will dial the second number.
To end the call, press the SOS button.
3sec.
Put device on charging base more than 30
seconds, and they will be paired automatically
via Bluetooth.
Silent mode button
Double-click this button to turn off voice
warnings, double-click the button again to turn
on voice warnings.
Double-click
SOS
Dimension: 62mm*47mm*17mm
Weight: 53g
Battery: Rechargeable, 3.7V, 1000mAh
Charging voltage: 5V DC
Waterproof: IP67
4 locating technologies: GPS, BLE, WIFI, LBS
Specification:
Don’t use & store the unit in dusty places.
Don’t put the unit in overheated or over cooled
places.
Clean the unit with a piece of dry cloth. Don’t
clean in chemicals, detergent.
Don’t disassemble or refit the unit.
Using other batteries will cause unwanted
situation.
Cautions:
Please comply with the instructions to extend the
unit life:
Warning: Keep the IMEI and SIM in confidential, or
your privacy may expose.
A QI charger provides a quick charging and easy
to use.
The wireless charging pad is not included in the
package.
2/ Wireless Charging
Charging Base
Personal Mobile Alarm System
FCC& ISDE Statement
This device complies with Part 15 of the FCC Rules and with
Industry Canada licence-exempt RSS standard(s).Operation is
subject to the following two conditions:
(1)this device may not cause harmful interference, and (2)this
device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et
aux normes RSS exemptées de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux
conditions suivantes :(1)cet appareil ne doit pas causer
d’interférences nuisibles, et (2)cet appareil doit accepter toute
interférence reçue, y compris les interferences pouvant
entraîner un fonctionnement indés
Changes or modifications to this unit not expressly approved
by the party responsible forcompliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonableprotection against harmful interference in a
residential installation. This equipment generates,uses and can
radiate radio frequency energy and, if not installed and used in
accordance withthe instructions, may cause harmful
interference to radio communications. However, there is
noguarantee that interference will not occur in a particular
installation. If this equipment doescause harmful interference
to radio or television reception, which can be determined by
turningthe equipment off and on, the user is encouraged to try
to correct the interference by one ormore of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.
This device meets the exemption from the routine evaluation
limits in section 2.5 of RSS 102 and compliance with RSS
102 RF exposure, users can obtain Canadian information on
RF exposure and compliance.
cet appareil est conforme à l'exemption des limites
d'évaluation courante dans la section 2.5 du cnr - 102 et
conformité avec rss 102 de l'exposition aux rf, les
utilisateurs peuvent obtenir des données canadiennes sur
l'exposition aux champs rf et la conformité.
This equipment complies with Canada radiation exposure
limits set forth for an uncontrolled environment.
Cet équipement est conforme aux limites d'exposition aux
rayonnements du Canada établies pour un environnement
non contrôlé.
Radiation Exposure Statement for Charging Base
This equipment should be installed and operated with
minimum distance 0cm between the radiator & your body.
Cet équipement doit être installé et utilisé à une distance
minimale de 0 cm entre le radiateur et votre corps.
Radiation Exposure Statement for Personal Mobile Alarm
System
Specific Absorption Rate (SAR) information:
This Personal Mobile Alarm System meets the government's
requirements for exposure to radio waves. The guidelinesare
based on standards that were developed by independent
scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a
substantial safety margin designed to assure the safety of all
persons regardless of age or health. FCC/ISED RF Exposure
Information and Statement the SAR limit of FCC/ISED is1.6
W/kg averaged over one gram of tissue. Device types:
Personal Mobile Alarm System has also been tested against
this SAR limit. This device was tested for typical body-worn
operations with the back of the Personal Mobile Alarm
System kept 10mm from the body. To maintain compliance
with FCC/ISED RF exposure requirements, use accessories
that maintain an 10mm separation distance between the
user's body and the back of the Personal Mobile Alarm
System .The use of belt clips, holsters and similar
accessoriesshould not contain metallic components in its
assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC/ISED RF exposure
requirements, and should be avoided.
Informations sur le débit d'absorption spécifique (DAS) :
Ce système d'alarme mobile personnel répond aux exigences du
gouvernement en matière d'exposition aux ondes radio. Les
directives sont basées sur des normes élaborées par des
organisations scientifiques indépendantes grâce à une évaluation
périodique et approfondie d'études scientifiques. Les normes
comprennent une marge de sécurité substantielle conçue pour
assurer la sécurité de tous. Informations et déclaration FCC/ISED
sur l'exposition aux RF la limite SAR de la FCC/ISED est de 1,6
W/kg en moyenne sur un gramme de tissu.
Le système d'alarme mobile personnel a également été testé par
rapport à cette limite SAR. Cet appareil a été testé pour des
opérations typiques portées sur le corps avec l'arrière du système
d'alarme mobile personnel maintenu à 10 mm du corps. Pour
maintenir la conformité aux exigences d'exposition RF FCC/ISED,
utilisez accessoires L'utilisation d'accessoires qui ne satisfont pas
à ces exigences ne peut maintenir une distance de séparation de
10 mm entre le corps de l'utilisateur et l'arrière du système
d'alarme mobile personnel. L'utilisation de clips de ceinture,
d'étuis et d'accessoires similaires ne doit pas contenir de
composants métalliques dans son sont conformes aux exigences
d'exposition RF FCC / ISED et doivent être évitées.