secuRa QMT35 INSTRUCTION MANUAL We'll Make It Stress-Free If you have any questions along the way, just give us a call.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS - PLEASE READ ENTIRE MANUAL PRIOR TO USE R f r etting starte , ~ 's rr d ~ sure this mo is pertec or you! 1 2 DoesyourlV (including accessories) weigh more than 50 lbs. (22.6 kg}? What is your wall made of? -- No - Perfect! Yes - This mount is NOT compatible. Visit secura-av.
Dimensions 3-0 TV INTERFACE _ [ 100mm] 3.94in [ 400mm ] 15.751n r1\ ! I I ~ 18• 1ii (~ 17 I i~:,I :I,t [ 400mm ] 15.75in I I [ 100mm] 3.94in TOP VIEW - RETRACTE=D _ __, WALL PLATE SIDE VIEW - TILT RANGE 1-- [406.4mm ] ----J I 16.00in I J_ = = = _L [ 100mm ] 3.94in [ 65.4mm ]J m ~ ~ ~ ~ ~~ : ; ' 2.57in ~ OPENING [ 449mm] 17.68in OPENING ~- FULLV ASSEMBLED MOUNT T~it L [ s4mm ] 2.
Parts and Hardware A WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! - NOTE: Not all hardware included will be used. Parts and Hardware for STEP 1 (D T TV Screws (qty. 4 each) (qty. 4 each) Spacers TV Bracket [If necessary] (qty.
Parts and Hardware for STEP 2 Wall Plate CD (qty. 1) For concrete installations ONLY Lag Bolts 11~~ttHMr<\-O~\\-¼~-{\-(\\~k-(\\-{~~ CD 1/4 X 2¾ in. (qty. 4) A CAUTION: Do not use in drywall or wood Concrete Anchors cm, Washers CD 0 (qty. 4) Fischer UX10 x 60R (qty. 4) 1 / 4 in .
STEP 1: Attach Brackets to TV 1.1 Select TV Screw Diameter 1.2 Select TV Screw Length Test the three screw diameters (M4, M6 and M8) in the threaded inserts on the back of your TV to determine which screw diameter fits your TV. 8: For flat-back TVs, no spacers required. CD b: Spacers CD supplied for: • • Round (irregular) back TVs Extra space needed (for cables or inset mounting holes) a J lo ___ ____ d,11 I FLAT BACK ;( (ROUND BACK INSET HOLES CABLES1 Standard configurations are shown.
1.3 Attach TV Brackets Center the TV brackets (D and (Dover your TV hole pattern as shown - making sure the brackets are level. \Si NOTE: The tilt tension knobs© on TV brackets (D and (D should be oriented to the outside edges. Install using the screw/washer/spacer combination (a) or (b) you selected for your TV. .A CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. lighten the screws only enough to secure the TV bracket to the TV.
STEP 2A: Attach Wall Plate [Wood Stud Installation] • Drywall covering the wall must not exceed 5/8 in. (16 mm) • Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1½ x 3½ in. (38 x 89 mm) • Minimum horizontal space between fasteners: 16 in. (406 mm) A Max. 5/8 in. (16mm) AMin.16in. L 0 (406mm) Verify and mark the CENTER of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.
1/8 m. (3mm) --- Drill four pilot holes using a 1/8 in. (3 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2¾ in. (70 mm). Be sure to drill into the center of the studs. CD CD G. Install wall plate using four lag bolts and four washers Tighten the lag bolts only until they are pulled firmly againstthe wall plate.
STEP 28: Attach Wall Plate [Solid Concrete or Concrete Block Installation] A CAUTION: Avoid potential personal injury or property damage! • Mount the wall plate CD directly onto the concrete surface • • • Minimum solid concrete thickness: 8 in. (203 mm) Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm) Minimum horizontal space between fasteners: 16 in. (406 mm) AMin. 16 in. ~06 mr_n) CD Position the wall plate on the wall at your desired height.
CD and four washers 8. Insert four anchors (D. Install wall plate (Dusing four lag bolts A CAUTION: Be sure the anchors are seated flush with the Tighten the lag bolts only until they are pulled firmly against the wall plate. concrete surface. A CAUTION: Avoid potential personal injury or property damage! All four lag bolts CD MUST BE firmly tightened to prevent unwanted movement of the wall plate
STEP 3: Attach TV to Wall Plate li:J:\. HEAVY! You may need ~ assistance with this step. , ,' / _.......:,, ... , / , ,,-/ / ,✓/ / /::: ,/ , / ,,/ Hook TV brackets (D and (D onto wall plate (D. 12 IMPORTANT: You will hear an audible click when the TV brackets (D and (Dare securely fastened to the wall plate (D.
Adjustments TILT REMOVING THE TV LATERAL SHIFT ICII ®o•0 •cm, I CD Loosen the knob on TV brackets and (9 to adjust the tilt of your TV. Tighten the knob when your TV is set to the desired tilt. Slowly slide the TV along wall plate CD. Pull down on the straps on TV brackets and (9 and lift the TV up and out away from the wall plate (9.
secuRa Milestone AV Technologies 6436 City West Parkway Eden Prairie, MN 55344 USA P: 800-359-5520 info@Milestone.com Milestone AV Technologies EMEA Headquarters Franklinstraat 14 6003 DK Weert, Netherlands Milestone AV Technologies Australia Office Unit 20 / 33 Meakin Road Meadowbrook OLD 4131, Australia P: +31 (0) 495 580 852 UK: 0800 056 2853 sa nus.e uro pe@M iIestone.
Milestone AV Technologies, Australia Pty Ltd ACN 163 436 039 Unit 20 / 33 Meakin Road, Meadowbrook QLD 413, Australia +61 (0) 7 3299 7000 Addendum - Australian Consumer Law - Warranty against defects Milestone AV Technologies Australia Pty Ltd warrants its Milestone/Secura products to be free of defects in material and workmanship for the product's Warranty Period . The Warranty Period commences on the original purchase date of the product.