080P FULL HD Baby Monitor User Manual OK V1.
1.What’s Included: OK 1.1: Camera*1 1.2: LCD Monitor*1 1.3: Mounting Bracket*1 1.4: Power Adaptor*2 1.5: Type-C Cable*1 1.6: Micro USB Cable*1 1.7: Screws*1 1.
2.Key and Interface Introduction 1 2 + 3 4 6 5 1.Microphone 2.Lens 3.Photoresistance 4.Speaker 5.Power Port 6.Digital Temp Sensor Lens 2.1: Back button: ①Press the button to return to the previous step, press again to enter the setting ②In the main menu, press the button to return to the previous menu 2.2: Camera Switch Button: Press the button to switch camera from one to the next . 2.3: Direction Button: ①In Monitoring Mode the button could control the Pan and Tilt of the camera.
audiowhile talk function stop. 2.8: Sound Detection (VOX) Button: Press to open sound detection(On the display will show )Press again to turn off sound detection(On the display will disappear) 2.9: Power On/Off Button: Long press to turn on/off the unit ,short press to enter standby mode. 2.10: External Antenna: Put the antenna up the signal will reach the best state. 2.11: Bracket 2.12: Speaker 3.Connect the camera to the Monitor 3.
4.Add new camera 4.1: Enter the main menu and choose camera ( )→choose channel→ Double press OK button to start matching →Configuring (Pic 1)→ Connected (Pic 2) 4.2: If can’ t add the camera successfully please check if the camera is powered . If camera already been powered then please reset the camera and add the camera again according to step 4.1. 4.3: If need to connect 4 cameras then add from CH1 to CH4. Choose the channel when add cameras to the related channel.
5.Feed Timer Setting 5.1: Enter the menu to set up Feed timer( )---up and down to select time left and right choose single time/ recycle/turn on or off the clock. 5.2: After set the feed timer you can choose single time or recycle. 5.3: If you don’ t need feed timer function please close the clock.
6. Sound Detection 6.1: Press OK button to enter the main menu and choose Sound detection ( ) There are low/medium/high/optional. 6.2: Press VOX button on the top will turn on press again to turn off. 6.3: When the camera detected the DB range over the settings the LCD screen will lighten up and show the icon in the middle of the screen. There will be an alarm sound like di di about 30S, if the camera keep detected sound over settings it will send alarm sound continuously.
7.Temperature Detection Alarm 7.1: Temperature alarm setting could be (ºC) or (ºF) according to actual usage. 7.2: The default temperature is 18-30ºC once the temperature lower or higher than the range will send alarm 7.3: The temperature alarm need to be shut down manually if it keep alarm due to temperature issue.
8.Play the lullaby 8.1: Enter the main menu and choose the lullaby icon ( )could select No.1-No.6 lullabies .During the play the lullaby the information will show on the left corner of the screen. 8.
9.Display Settings 9.1: The display settings have Dormant/ LUMI 9.2: Dormant mode default 1Min( /ALWAYS ON ( )/10Min( )/30Mini( ) could adjust according to actual usage.
10. Video Recording 10.1: Enter the main menu and select the record icon ( ) The record file can choose 0.5Hr/1Hr/2Hr (Means how long to pack to one file) 12.2: If don’ t need to record could choose OFF.
11.Video Playback 11.1: Enter the menu and select the playback icon ( pick up the time of the video you want to play.
12.System Settings 12.
12.2: Back to factory settings( ) . Not suggest to use normally please contact the seller for assistant if have to. 12.
12.
13.Language Settings 13.1: The device support 8 language ENGLISH//JAPANESE/CHINESE/PORTUGUESE/ITALIAN/FRENCH/SPANISH/ GERMANY default is ENGLISH 13.2: Could adjust the language according to your request.After confirm the language please power off the monitor and restart .When connect the camera it will change to the language same as the monitor . Tips: When changing the language please make sure the camera is powered on.
14.
Questions and Answers: Q: The LCD monitor didn’ t show the camera ? A: ①Please check if the camera is powered on . ②If camera is powered on please reset the camera to factory settings and add the camera according to steps 4.1. Q: There is annoying sound when use the talk function in near distance? A: When the camera and monitor is within 2meter distance there might be some noise which is a normal Physical phenomena.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.