User Manaual

ManualsBrandsSECO-LARM ManualsElectronicsElectromagnetic Gate Lock

Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.

Electromagnetic Gate Locks

with Face or Surface Mounting

Manual

• Now with face and surface mounting

• For sliding or swinging gates

• Water resistant and vandal resistant

• Maintenance-free, factory-sealed design

• Dual-threaded conduit fitting

• Attractive stainless-steel housing

• Dual voltage: 12/24 VDC Operation

• No residual magnetism

• MOV Surge protection

• Complete mounting hardware included

Model

Holding Force

E-946FC-600Q

600-lbs (271kg)

E-946FC-1K2Q

1,200-lbs (544kg)

Summary of content (8 pages)

PAGE 1
Electromagnetic Gate Locks with Face or Surface Mounting Manual Model E-946FC-600Q E-946FC-1K2Q • • • • • Now with face and surface mounting For sliding or swinging gates Water resistant and vandal resistant Maintenance-free, factory-sealed design Dual-threaded conduit fitting Holding Force 600-lbs (271kg) 1,200-lbs (544kg) • • • • • Attractive stainless-steel housing Dual voltage: 12/24 VDC Operation No residual magnetism MOV Surge protection Complete mounting hardware included Note: Model numbers
PAGE 2
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Specifications: Model Holding force Operating voltage 12VDC Current draw 24VDC Operating temperature Dimensions Magnet Armature plate Weight (approx.) E-946FC-600Q E-946FC-1K2Q 600-lb (271kg) 1,200-lb (544kg) 12VDC or 24VDC 500mA 250mA 14°~131° F (-10°~55° C) 8”x111/16”x19/16” 811/16”x21/2”x19/16” (203x43x40 mm) (220x63x40 mm) 71/4”x15/8”x9/16” 71/4”x23/8”x5/8” (185x41x14 mm) (185x61x16 mm) 6-lb (2.
PAGE 3
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Overview: E-946FC-600Q Armature screw Guide pin For face mounting* Electromagnet For surface mounting* Sexnut bolt Steel washer Rubber washer Steel washer For face mounting* Tamper cap For surface mounting* *NOTE: Each installation will use either face mounting OR surface mounting. No installation will use both. For more information on which type of mounting method to use, please see page 5, Installation.
PAGE 4
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Wiring Diagram: 12VDC Red White Black Green 12 VDC Red White Black Green 24 VDC GND IMPORTANT: Damage caused by improper connection will void warranty. 24VDC GND Maximum Distance from Power Source to Electromagnetic Lock: For a complete chart, please visit www.seco-larm.com.
PAGE 5
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Installation: 1. Determine type of gate: a. Single-swing gate: Gate swings on one end, and comes to rest on a fixed gate post when closed. In this case, a typical installation has the electromagnet face mounted to the gate post, and the armature plate connected to the free end of the gate with a Z bracket. Electromagnet Electromagnet Z Bracket Z Bracket Armature plate Armature plate b.
PAGE 6
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Installation, continued: 2. Mount the electromagnet. In most cases, the position of the electromagnet will determine the location of the armature plate. Make sure there is space to run the cable. a. Tape the template to the appropriate location. b. Drill four (E-946FC-1K2Q) or two (E-946FC-600Q) 9.5mm (3/8”) holes, one for each short hex screw. IMPORTANT: The holes must be 9.5mm (3/8”). No smaller or larger. c.
PAGE 7
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Installation, continued: 3. Mount the armature plate. Once the electromagnet is mounted, determine the correct position of the armature plate. Use the appropriate L bracket or Z bracket to position Z Bracket the armature plate so that it will lay against the electromagnet when activated. However, leave Armature plate a slight gap between the two so that the armature plate does not slam against the electromagnet when the gate is closed. a.
PAGE 8
SECO-LARM Electromagnetic Gate Locks with Face or Surface Mounting Troubleshooting: The gate does not lock. • Check that the wires are secure. • Check that the power supply is connected and operating. • Check that the unit is wired correctly. The gate locks, but can be easily forced open. • Check that the electromagnet and armature plate are properly aligned. • Check that the contact surfaces of the electromagnet and armature plate are clean and free from rust.