User's Manual

USER MANUAL
RADIO CONTROL TXS 2121 SERIES
Radio controller with 12 bit code transmission and
the possibility of partialisation of the code for
communal and personal command management. It
may be used together with other transmitters of the
same series and may be perfectly integrated with all
the receivers and the SEAV central electronic lines.
- Mod. TXS 1 new : one channel T1
- Mod. TXS 2 new : two channels T1, T2
- Mod. TXS 3 new : three channels T1, T2 e T3
TECHNICAL CHARACTERISTICS
- Powered by an alkaline battery : 12VDC (23A)
- Working frequency : 433,92 MHz
- Combinations : 1024 (12 bit code)
- Maximum consumption. : 25 mA
- Working temperature : -20 ÷ 70 °C
- Dimensions : 36x61x14mm.
TXS 1 new TXS 2 new TXS 3 new
DESCRIPTION OF FUNCTIONING
The transmitter, according to the model, is complete
with either 1, 2 or 3 buttons for the management of
either 1, 2 or 3 different uses.
PROGRAMMING
By pressing the 10 SW1 switches, moving them to
the “ON” or “OFF” position, the desired code may be
selected. Such a code must correspond to the code
which has been memorised on the receiver. (The
standard factory configuration: uneven “ON”).
FUNCTIONING PROCEDURES
a) Standard 12 bit models T1, T2, and T3.
The transmitter which is produced by the factory is
made up as follows:
TXS 1 new: Jumper J1 and J2 are not included
TXS 2 new: Jumper J1 (1-2). J2 not included.
b) TXS 3 new: Jumper J1 (1-2), J2 (2-3).
Channel separation: 1 communal and 1 or 2
private (if TXS 2 or TXS 3).
TXS 2 new: Jumper J1 (2-3), J2 not included.
TXS 3 new: Jumper J1 (2-3), J2 (1-2).
With this format the radio commander has a
communal code (T1) (e.g. condominium entrance
door) and one or two private uses (T2 and T3).
The separation of the code is the of the 4+6 type,
and so the first 4 switches of the SW1 are for the
codification of the communal code and the
remaining 6 are for the codification of the private
code.
c) Channel separation: 2 communal and 1 private
(only for TXS 3).
TXS 3 new: Jumper J1 (2-3), J2 (2-3)
With this format the radio commander has two
communal codes (T1 and T3) (e.g. condominium
entrance door) and one private use (T2).
The separation of the code is of the 4+6 type,
therefore the first 4 switches of the SW1 are for the
codification of the communal code and the
remaining 6 are for the codification of the private
code.
WARNING
− The alkaline 12VDC (23A) battery must be
changed every year in order to guarantee the correct
functioning of the transmitter.
− In order to substitute the dead battery remove the
plastic cover by sliding it off, take the old battery out
and insert the new one taking care to ensure that the
polarity corresponds to that indicated on the
container.
− The used battery must be disposed of correctly in
the apt recycling bins.
DECLARATION OF CONFORMITY
SEAV s.r.l. declares that the product
Radio commander TXS 2121 Series
is conformant to all of the requirements laid out in
the EC directive number: 99/5 which are based on
the following standards:
- ETS 300 683;
- ETS 300 220;
- EN 60335-1.
The sample which has been tested meets the
essential requirements which have been specified
above, on the basis of the results of the tests, as
demonstrated in the following reports:
EMC 906/99, RTX 903/99, LVD 505/00.
These reports have been verified by the organisation
notified. EMCCert Dr. Rasek (Identification Number:
0678).
Osimo, 09/10/00
GB