System Manual

ManualsBrandsSEAL INNOVATION ManualsComputers & AccessoriesSwimSafe Hub

www.sealswimsafe.com

@sealswimsafe

Getting your toes wet with SEAL SwimSafe.

What is SEAL SwimSafe?

SEAL SwimSafe is a swim monitoring device that detects if a swimmer is submerged for too long. The

system includes a hub, at least 2 SwimSafe bands and a charging tower. SwimSafe bands are worn

around a swimmer’s neck.

How does it work?

The SEAL SwimSafe system uses patented radio wave technology to continually monitor swimmers. The

monitoring happens through communication between the hub and SwimSafe bands. The two devices

communicate continually to ensure a swimmer is safe. If the swimmer is submerged below water more

than the set amount of time, communication between the band and hub will stop, and set off an alarm.

Once the alarm sounds, other swimmers should immediately get out of the pool and lifeguards or parents

should rescue the swimmer who is in distress.

I have my system, now what?

YAY! Welcome to the SwimSafe community, we are so glad that you have your system. As you unpack

your system you will have some combination of the following:

BAND HUB CHARGING TOWER

Follow the steps below to get your SwimSafe System up and running. You may also visit our website

sealswimsafe.com to access our video modules to learn more about how SEAL SwimSafe works.

Summary of content (12 pages)

PAGE 1
www.sealswimsafe.com @sealswimsafe Getting your toes wet with SEAL SwimSafe. What is SEAL SwimSafe? SEAL SwimSafe is a swim monitoring device that detects if a swimmer is submerged for too long. The system includes a hub, at least 2 SwimSafe bands and a charging tower. SwimSafe bands are worn around a swimmer’s neck. How does it work? The SEAL SwimSafe system uses patented radio wave technology to continually monitor swimmers. The monitoring happens through communication between the hub and SwimSafe bands.
PAGE 2
Table of Contents PAGE 1: Introduction PAGE 2: Table of Contents PAGE 3: Commercial System Manual PAGE 4: Commercial System Manual PAGE 5: Residential System Manual PAGE 6: Residential System Manual PAGE 7: Troubleshooting PAGE 8: Troubleshooting PAGE 9: FAQS PAGE 10: FAQS PAGE 11: What SEAL SwimSafe is Not.
PAGE 3
COMMERCIAL SYSTEM MANUAL Step 1: Plug hub and charging tower with band into wall outlet with SEAL SwimSafe charging cords. Let both charge overnight. All bands and the hub lights should be solid green, indicating they are fully charged. CHARGING TOWER HUB HUB UNDER POWER CHARGING TOWER UNDER POWER (power connect underneath charging tower) Step 2: Press the power button appear. on the hub. The LCD screen should light up and a welcome message will Step 3: Remove bands from the charging tower.
PAGE 4
Linking is the process of connecting the band to the hub so that monitoring of a swimmer can begin. By linking the band to the hub you are opening communication between the two, if communication is lost a full alarm will happen. Step 5: All bands are preset to our standard level, which will alarm if swimmer is submerged for 20 seconds. To change the swim level of a band place band in hub charging port and press the swim level button .
PAGE 5
RESIDENTIAL SYSTEM MANUAL Step 1: Plug hub into wall outlet with bands in charging port using SEAL SwimSafe charging cords. Let charge overnight. All bands and the hub lights should be solid green, indicating they are fully charged. ←← Wall Power Supply HUB WITH BANDS IN CHARGING PORTS HUB CONNECTED TO POWER Step 2: Press the power button appear. on the hub. The LCD screen should light up and a welcome message will Step 3: Remove bands from the charging tower.
PAGE 6
*Setting swim level on band can be done with hub plugged in or unplugged from a wall outlet* More about swim levels, please. Swim level should be determined by the ability of the swimmer. There are three levels, beginner, standard and advanced. Beginner/pink light will alarm if swimmer is submerged for 3 seconds, standard/blue light will alarm if swimmer is submerged for 20 seconds and advanced/light blue will alarm if a swimmer is submerged for 55 seconds.
PAGE 7
TROUBLESHOOTING Problem Cause Solution Hub screen not coming on Variety of reasons Hold down the power button for 5 seconds to reset hub and resume normal function Band appears to be in a deep sleep Band taken off of unplugged hub or charging tower Swipe band in from of the SEAL Band is erradictly flashing colors while charging Band is in extreme low battery Leave band on charging source (hub port or charging tower) over night. logo , band will light up and resume normal function.
PAGE 8
Low Battery Band Alert ● The band will flash red and chirp when in low battery. The hub will also chirp and state on its screen that a band is in low battery. ● A low battery band can either be unlinked to stop chirping or placed on a charger (hub or tower). To charge band, hub or tower must be plugged into wall outlet. Low Battery Hub Alert ● The hub will flash red and chirp to indicate it is in low battery. ● To resolve, plug hub into wall outlet and let charge.
PAGE 9
FAQS Where can I buy this product? The product is currently only available for commercial use. For commercial inquiries or to join the waitlist for our residential unit when available, visit sealswimsafe.com. Where can I test the SEAL SwimSafe system? SEAL can only be tested in large bodies of water like a pool or lake. Can I test the band in a bathtub, hot tub, bucket of water or sink? No. SEAL SwimSafe will only alarm in large bodies of water or inground pools deeper than 2 feet.
PAGE 10
What happens when the band or hub battery is low? If any component is in low battery the hub will notify the user of this several minutes before the battery level becomes critical. If a single band is low, it will chirp and blink red. What happens if two bands alarm at once? Both bands will flash red and white with audible alarms, indicating both swimmers need help. The hub will alarm. Does it float? Yes, with the black foam sleeves attached. It will allow the user to swim under the water.
PAGE 11
The Seal SwimSafe band uses a low-voltage battery that is completely enclosed in plastic. The hub and charger should not be submerged in water. WHAT SEAL SWIMSAFE IS NOT. ● It is not a substitute for the cornerstones of safe swimming: Early effective swim lessons, vigilant and well-trained lifeguards and parents, and a safe swimming environment. ● It is not a replacement for vigilant parental and/or lifeguard supervision. ● It is not a rescue device.
PAGE 12
REGULATORY STATEMENTS AND DISCLAIMERS 1. FCC COMPLIANCE STATEMENTS The following applies to the following products/models: ● SEAL SwimSafe 2.0 Charging Tower / SC220 This device complies with part 18 of the FCC Rules. The following applies to the following products/models: ● SEAL SwimSafe 2.0 Hub / SH200 ● SEAL SwimSafe 2.0 Band / SB200 Changes or modifications not expressly approved by SEAL Innovation, Inc. could void the user’s authority to operate the equipment.