HYDATA USERMANUAL SOFTWARE CO., LTD. www.hydata.com SRT FOR SEAGATE SCSI HDD VERSION 2.
HYDATA SRT FOR SEAGATE SCSI Technical Support You may obtain and update the latest software version via our website. If you encounter any problem during software installation or action, please feel free to contact our suppliers. About User Manual SRT FOR SEAGATE SCSI HDD user manual was published in March 2010. This user manual mainly describes SRT FOR SEAGATE SCSI HDD installation and configuration. Please read this manual thoroughly to understand data recovery technology regarding SCSI drives.
HYDATA SRT FOR SEAGATE SCSI Table of Contents 1 Introduction ........................................................................................................... 4 1.1 Product Features............................................................................................................................................4 1.2 Product Application .......................................................................................................................................4 1.
HYDATA SRT FOR SEAGATE SCSI 4.4.5 Change Block Size ................................................................................................................................ 40 4.4.6 HDD Formatting ................................................................................................................................... 40 4.4.7 HDD Setting .......................................................................................................................................... 44 4.
HYDATA SRT FOR SEAGATE SCSI 1 Introduction The SCSI hard drives are widely used for servers and other high-end software products, however, 24-hour interrupted working as well as many years of running, the damage rate of SCSI HDD appears to be rising in recent years. Generally the server HDD accommodates the very important data, if the data was lost, the consequence is hard to imagine. SRT FOR SEAGATE SCSI HDD is specially designed to repair the firmware issue occurring on Seagate SCSI HDD.
HYDATA SRT FOR SEAGATE SCSI SCSI-3 Before Adaptec and later SCSITA codified the terminology, the first parallel SCSI devices that exceeded the SCSI2 capabilities were simply designated SCSI-3. These devices, also known as Ultra SCSI and fast-20 SCSI, were introduced in 1996. The bus speed doubles to 20 MB/s for narrow (8 bit) systems and 40 MB/s for wide (16-bit).
HYDATA SRT FOR SEAGATE SCSI SPI Ultra2 SCSI-3 SPI-2 8 8 bits 40 MHz 40 MBps Ultra2/Wide SCSI-3 SPI-2 16 16 bits 40 MHz 80 MBps Ultra3 SCSI-3 SPI-3 16 16 bits 40 MHz 160 MBps Ultra320 SCSI-3 SPI-4 16 16 bits 80 MHz 320 MBps SAS Serial Attached SCSI (SAS) as a new storage interface is evolved from the Parallel SCSI physical storage interface, which is developed by ANSI INCITS T10 Technical Committee.
HYDATA SRT FOR SEAGATE SCSI Available, No Capacity, and this situation is usually due to translator damage or GList error. SRT FOR SEAGATE SCSI HDD is easy-to-use, you only need to select SCSI drive to be repaired, and click "Repair HDD" button to repair on your own. SRT FOR SEAGATE SCSI HDD is not only applicable to professional data recovery companies but also network administrators using servers in large and medium enterprises.
HYDATA SRT FOR SEAGATE SCSI Seagate Original Model Series Cheetah 18LP Cheetah 18XL Cheetah 36LP Capacity Model Interface ST318203LW 18GB SCSI ST318203LWV 18GB SCSI ST318203LC 18GB SCSI ST318203LCV 18GB SCSI ST39103LW 9.1GB SCSI ST39103LWV 9.1GB SCSI ST39103LC 9.1GB SCSI ST39103LCV 9.1GB SCSI ST318233LWV 18GB SCSI ST318233LCV 18GB SCSI ST39133LWV 9.1GB SCSI ST39133LCV 9.1GB SCSI ST318203FC 18GB FC ST39103FC 9.1GB FC ST39204LW 9.
HYDATA SRT FOR SEAGATE SCSI Cheetah 36LP Cheetah 36XL Cheetah 36ES Cheetah 73LP Cheetah 10K.6 ST336704FCV 36GB FC ST336704FC 36GB FC ST39205LW 9.1GB SCSI ST39205LC 9.
HYDATA SRT FOR SEAGATE SCSI Cheetah 10K.6 Cheetah 10K.7 Cheetah X15 Cheetah X15 36LP ST373307LC 73GB SCSI ST373307FC 73GB FC ST3146807LC 146GB SCSI ST3146807FC 146GB FC ST373207LW 73GB SCSI ST3146707LW 146GB SCSI ST3300007LW 300GB SCSI ST373207LC 73GB SCSI ST373207FC 73GB FC ST3146707LC 146GB SCSI ST3146707FC 146GB FC ST3300007LC 300GB SCSI ST3300007FC 300GB FC ST39251LC 9.1GB SCSI ST318451LC 18GB SCSI ST39251LW 9.
HYDATA SRT FOR SEAGATE SCSI Cheetah X15 36LP Cheetah 15K.3 Cheetah 15K.
HYDATA SRT FOR SEAGATE SCSI Cheetah 15K.4 ST3146854SS 146GB SAS Capacity Model Interface IBM-ESXS-ST318203LW 18GB SCSI IBM-ESXS-ST318203LWV 18GB SCSI IBM-ESXS-ST318203LC 18GB SCSI IBM-ESXS-ST318203LCV 18GB SCSI IBM-ESXS-ST39103LW 9.1GB SCSI IBM-ESXS-ST39103LWV 9.1GB SCSI IBM-ESXS-ST39103LC 9.1GB SCSI IBM-ESXS-ST39103LCV 9.1GB SCSI IBM-ESXS-ST318233LWV 18GB SCSI IBM-ESXS-ST318233LCV 18GB SCSI IBM-ESXS-ST39133LWV 9.1GB SCSI IBM-ESXS-ST39133LCV 9.
HYDATA SRT FOR SEAGATE SCSI Cheetah 36LP Cheetah 36XL Cheetah 36ES Cheetah 73LP Cheetah 10K.6 IBM-ESXS-ST336704LWV 36GB SCSI IBM-ESXS-ST336704FCV 36GB FC IBM-ESXS-ST336704FC 36GB FC IBM-ESXS-ST39205LW 9.1GB SCSI IBM-ESXS-ST39205LC 9.
HYDATA SRT FOR SEAGATE SCSI Cheetah 10K.6 Cheetah 10K.
HYDATA SRT FOR SEAGATE SCSI Cheetah X15 36LP Cheetah 15K.3 Cheetah 15K.
HYDATA SRT FOR SEAGATE SCSI Cheetah 15K.4 IBM-ESXS-ST3146854FC 146GB FC IBM-ESXS-ST3146854SS 146GB SAS Seagate OEM HP Models Series Capacity Model Interface COMPAQ BD018122C0 18GB SCSI COMPAQ BD03695A27 36GB SCSI COMPAQ BD07285A25 73GB SCSI COMPAQ BD03695A24 36GB SCSI COMPAQ BD07288277 73GB SCSI COMPAQ BD14685A26 146GB SCSI COMPAQ BD01864552 18GB SCSI B82-80C2 9.1 GB SCSI HP 1.
HYDATA SRT FOR SEAGATE SCSI 2 Hardware Installation This chapter briefly describes initial installation. 2.1 Product Information Please confirm the following accessories involved in the product prior to installing software. HASP USB key ---1 pc Or Note: one of the two USB keys is for lifetime-use, the other is time-limited (i.e. you may use it during a limited period). Installation Program CD---1 pc 2.
HYDATA SRT FOR SEAGATE SCSI Memory: 256MB and above Hard disk: 1.5G and above Display: 17-inch and above Resolution: 1024*768 and above 2.3 Hardware Installation Please connect required hardware as per the following procedures: 1. Hook up SCSI card to the PCI slot 2.
HYDATA SRT FOR SEAGATE SCSI 68pin Drive Connection: Page | 19
HYDATA SRT FOR SEAGATE SCSI 3. Start System: Install SRT FOR SEAGATE SCSI HDD (please refer to the third Section) 4.
HYDATA SRT FOR SEAGATE SCSI 5. Restart the computer system 6. Check the installation status from the Device Manager Click on your start button -> then Run and type in "devmgmt.msc". You may see the model of SCSI Adapter and disk drive status from Device Manager in Microsoft Windows. The figure is as follows: NOTE: under Universal Serial Bus controllers: Aladdin HASP Key not available in trail version 7.
HYDATA SRT FOR SEAGATE SCSI 3 Software Installation 3.1 Software Installation Procedures 1. Insert software CD into floppy drive or download the software package from HYDATA website, double-click an executable file named "SEAGATEEN.exe" to perform installation. The Agreement License dialog box will display then, if you want to continue, please click I Agree button.
HYDATA SRT FOR SEAGATE SCSI 2. Click "Next", go to installation interface, the system gives a default path: C:\Program Files\HYDATA\SRT SEAGATE EN 2.0000, you may also click the Browse button to select a new folder. 3. Click "Next" button to enter the window where you can select the folder in the Start menu for SRT FOR SEAGATE SCSI shortcut.
HYDATA SRT FOR SEAGATE SCSI 4. Press the Install button to start SRT FOR SEAGATE SCSI installation process. 5. Click "Next", Installation Program starts to copy files required for running program to installation directory.
HYDATA SRT FOR SEAGATE SCSI 6. Click Finish, and the installation process is successfully completed. Note: You must reboot and load the new drive after you install SCSI HDD Adapter or add a new SCSI HDD. If device not found by the system or software, you may try to reboot your computer.
HYDATA SRT FOR SEAGATE SCSI 4 Menu Description and User Guide 4.1 Main Menu Main Menu consists of four functions: 4.1.1 Accessory Function This function includes Display P/GList, Add to GList, Change HDD Capacity & Block Size, HDD Formatting, etc. 4.1.2 Repair "Medium Error" It mainly focuses on "model available, no capacity", which is the most important function of SRT FOR SEAGATE SCSI HDD.
HYDATA SRT FOR SEAGATE SCSI 4.1.3 About It mainly includes the version information regarding SRT FOR SEAGATE SCSI HDD. 4.1.4 Help It mainly includes brief product introduction, download address of user manual, after-sale contacts, etc. 4.2 User Guide 4.2.1 Connection Notices Seagate SCSI HDD must be detected by this software before repairing.
HYDATA SRT FOR SEAGATE SCSI Please pay attention to the following operations when connecting multiple SCSI devices: Narrow (50pin) SCSI controller can make a daisy chain to seven extra SCSI devices. Counting the controller, there are eight SCSI devices totally. Wide (68pin) SCSI controller can make a daisy chain to fifteen extra SCSI devices. There are sixteen SCSI devices totally through counting the controller.
HYDATA SRT FOR SEAGATE SCSI Figures 1 and 2 show views of the drive ID select jumper connectors. Figure 3 shows the option select jumper connector for all models. Figure 1 shows the drive’s J5-auxiliary jumper connector. Both J5-auxiliary and J6 have pins for selecting drive ID and for connecting the remote LED cable. Only one or the other should be used, although using both at the same time would not damage the drive.
HYDATA SRT FOR SEAGATE SCSI Figure 2 J5 jumper header (on LW models only) Page | 30
HYDATA SRT FOR SEAGATE SCSI Figure3 J2 option select header (on LW models only) Notes for Figures 1, 2, and 3: [1] Notes explaining the functions of the various jumpers on jumper header connectors J2, J5, and J6 are given here and in Section 8.1.2. The term “default” means as standard OEM units are configured with a jumper on those positions when shipped from factory. “Off” means no jumper is installed; “On” means a jumper is installed. OFF or ON underlined is factory default condition.
HYDATA SRT FOR SEAGATE SCSI J2 jumper installation Jumper function description SE On Forces drive to use single-ended I/O drivers/receivers only. Off Drive can operate on the interface in low voltage differential mode or single-ended, depending on the voltage state of the I/O “DIFFSNS” line. Default is SE jumper not installed. DS Off ME Off Off On On Off On On WP On Spindle starts immediately after power up - Default setting.
HYDATA SRT FOR SEAGATE SCSI 4.3 Function Description and Operation 4.3.1 SEAGATE SCSI HDD Checking Before repairing SCSI HDD selected, you may make a detection using "HDD Checking" button. This button is used to evaluate if your SCSI HDD can be repaired by SRT FOR SEAGATE SCSI HDD besides viewing the bios of SCSI Adapter.
HYDATA SRT FOR SEAGATE SCSI 2. After HDD selection, click "Next" button to enter the window where the HDD selected will be displayed on the top-left of the interface, click "Check HDD" under Current Block Size on the right, and then the detection information will show on the bottom left of window.
HYDATA SRT FOR SEAGATE SCSI 3. If it is a normal Seagate SCSI HDD, the display window will show start time, HDD vendor, model, firmware, SN, capacity, block size, end time and detection results. If it is a SCSI HDD with "0 LBA" fault, the window will show start time, HDD vendor, model, firmware, SN, end time and detection results.
HYDATA SRT FOR SEAGATE SCSI ================== Start HDD Checking ================== Start Time 2010-4-2 12-10-38 HDD Vendor:SEAGATE Model:ST336607LC Firmware:0007 SN:3JA1QXJT End Time 2010-4-2 12-11-19 ================== HDD Checking Completed ================== Detection Result(s): HDD Capacity Error (Medium Error), you may use "Common Defect Repair" function. After detection, we suggest you use the most important function of this software-Common Defect Repair.
HYDATA SRT FOR SEAGATE SCSI This moment, the normal capacity has been displayed on the top-left of drive attribution window.
HYDATA SRT FOR SEAGATE SCSI 4.4 Accessory Function and Description 4.4.1 Add to GList If you need to add to GList manually, you may select "Add to GList" button, fill the LBA value in the Edit Box. You may record LBA value when encountering damage sectors, and use "Accessory Function" to repair. 4.4.
HYDATA SRT FOR SEAGATE SCSI 4.4.3 Display GList View number of GList and location If the running speed became slow, and the dialog box shows error when adding bad sectors to GList, you may use this function to view if the GList is already full. 4.4.4 Change HDD Capacity HPA HPA belongs to a standard of SCSI, in other words, it is used to set the max sector number for the drive to be read and hides the high-end info by changing HPA.
HYDATA SRT FOR SEAGATE SCSI 4.4.5 Change Block Size This function is used to change sector size in bytes, and the max is 2048. Non-standard sector size is usually adopted for many special serves in RAID system, e.g. 520 byte per sector. It will become effective immediately after changing (depending on drive firmware support), and it’s necessary to perform factory low level format (LLF) on the supported device again after changing. 4.4.
HYDATA SRT FOR SEAGATE SCSI This function can repair damage drives. Factory LLF can completely repair ECC bad tracks existing on drive surface or logical error caused by running, even many maintenance departments always repair such kind of patient drives using this function. SCSI drives with "0 LBA" fault can be fixed through LLF regardless of data contained on drive.
HYDATA SRT FOR SEAGATE SCSI FOV (Format Option Valid): DPR, DCR, STP, IP and DSP are valid, only when set FOV to "1". Otherwise, these bits will be set to "0", and targeter will use default value. DPR (Disable PList): set DPR to "1", PList will not be transferred to targeter. However, PList is provided by device manufacturer, keep unchanged.
HYDATA SRT FOR SEAGATE SCSI Defect Descriptors of Block Format 0 (MSB) 1 Block Number of Defect Block 2 3 (LSB) Index Format (100b) Index pulse describes start position of each track on the drive. The first four bytes of Index format contain defect cylinders and defect heads.
HYDATA SRT FOR SEAGATE SCSI Sector Format Sector Format is similar to Index Format in structure, but its 4~7 Byte contains sector number of defect block. Herein sector number FFFFFFFFh represents the whole track is defective. Defect Descriptor of Sector Format 0 (MSB) 1 Cylinder Number of Defect Block (LSB) 2 3 4 5 Head Number (MSB) Defect Sector 6 7 (LSB) It’s necessary to understand SCSI factory LLF parameters well for IP mode, hence format with IP mode are not involved in wizard version. 4.4.
HYDATA SRT FOR SEAGATE SCSI 4.5 Appendix 4.5.1 HYDATA SOFTWARE End-User License Agreement ("EULA") Reading carefully: Please make sure that you have read and understood all the rights and restrictions mentioned in End-User License Agreement ("Agreement"). You should read Agreement carefully prior to installing to decide whether to accept all the terms of this Agreement.
HYDATA SRT FOR SEAGATE SCSI When happening serial number and registration code leakage or dongle subtenancy, whether unintentional acts or not, it would be recognized to be intentional. HYDATA Software will claim for compensations for economic loss caused by the users’ acts. 2.
HYDATA SRT FOR SEAGATE SCSI or upgrading version ); (c)if HYDATA Software provides you with the software's replacement, modification version or any upgrading version, you may go on using the software for accepting replacement, modified version or any upgrading version and accompanying Agreement. All the former versions will be terminated; (d)for genuine user, once you got the serial number and the register coed representing you have got the permanent use right, no exchange.
HYDATA SRT FOR SEAGATE SCSI 4.5.2 Various SCSI Interfaces 4.5.
HYDATA SRT FOR SEAGATE SCSI 5 Product Upgrade and Customer Service 5.1 Product Upgrade Description This product series mainly focus on repairing SCSI HDD, which has been subject to several revisions.
HYDATA SRT FOR SEAGATE SCSI But some software will add multiple driver program files during the process of installation, and it will lead to the state of abnormal driving. The figure is as follows: Under the circumstances you may uninstall other software or reinstall system. Ensure the uniqueness of driver program files.
HYDATA SRT FOR SEAGATE SCSI A: Technical Support is affiliated with software development department with higher confidentiality, so telephone and network are not allowed. The client's Email must be filtered through the mail gateway first. Recently HYDATA SOFTWARE has already built a perfect mail service system, so we can handle users' suggestions and consultations ASAP.
HYDATA SRT FOR SEAGATE SCSI 5.3 Customer Service Contacts SRT FOR SEAGATE SCSI TECHNOLOGY R&D CENTER CHINA HARBIN HYDATA SOFTWARE CO., LTD. Add: Room 396,East Zone, Chuanbo Cyber Plaza, Nangang District, Harbin, Heilongjiang Prov., China Tel: +86 451 87529888 Fax: +86 451 87529888 Customer QQ :287529888 Contact: Zhe Feng Website: http://en.hydata.com Product Sale Email: sales@hydata.com Technical Support Email: support@hydata.