INSTALLATION AND MAINTENANCE MANUAL FOR SEA TEL MODEL ST14 SATELLITE TV RECEIVE-ONLY ANTENNA Sea Tel, Inc. 4030 Nelson Avenue Concord, CA 94520 Tel: (925) 798-7979 Fax: (925) 798-7986 Web: : www.cobham.com\seatel Sea Tel Europe Unit 1, Orion Industrial Centre Wide Lane, Swaythling Southampton, UK S0 18 2HJ Tel: 44 (0)23 80 671155 Fax: 44 (0)23 80 671166 Web: www.cobham.com\seatel Sea Tel Inc is also doing business as Cobham Antenna Systems September 26, 2011 Document. No.
Sea Tel Marine Stabilized Antenna systems are manufactured in the United States of America. Sea Tel is an ISO 9001:2008 registered company. Certificate Number 13690 issued March 14, 2011. Copyright Notice All Rights Reserved. The information contained in this document is proprietary to Sea Tel, Inc.. This document may not be reproduced or distributed in any form without the consent of Sea Tel, Inc. The information in this document is subject to change without notice.
ST14 Ku-Band TVRO 1. 2. Table of Contents INSTALLATION ............................................................................................................................................................................................. 1-1 1.1. SITE SELECTION AND CABLE ROUTING PATH .......................................................................................................................................... 1-1 1.2. DETERMINE YOUR CABLES................................................
Table of Contents 3. 4. 5. 6. ST14 Ku-Band TVRO 2.3.10. SAT6 - Sixth Satellite Parameters................................................................................................................................... 2-7 2.3.11. FACTORY SETTINGS................................................................................................................................................................ 2-7 2.4. SAVING THE SETUP PARAMETERS ...........................................................
ST14 Ku-Band TVRO 7. 8. Table of Contents 6.8. POWER REQUIREMENTS ................................................................................................................................................................................ 6-3 6.9. ENVIRONMENTAL ........................................................................................................................................................................................... 6-3 COMPUTER INTERFACE ................................
Table of Contents ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK vi
ST14 Ku-Band TVRO 1. Installation Installation Installation of your ST-14(D/E/M) Antenna system must be accomplished by or under the supervision of an authorized Sea Tel dealer for the Sea Tel Limited Warranty to be valid and in force. Good planning of the installation will provide the best results. Below is some guidance on issues that are important to consider when planning the installation. Planning is the key to a good installation.
Installation 1.2. ST14 Ku-Band TVRO Determine your Cables In addition to the required Coaxial cable that will interconnect the above decks equipment with the below decks equipment, you will need to determine what cables are going to be used to interconnect satellite receivers to the televisions and if installed the surround sound system. The below guide may be used to help determine which cable type is best suited for your installation.
ST14 Ku-Band TVRO 1.3. Installation Required Tools The following tools will be required to install the ST14: 1. Masking tape 2. Center punch 3. Hammer 4. Electric Drill 5. 7mm Drill Bit 6. 1” hole saw 7. Small hand or electric saber saw 8. 10mm Socket Wrench or Nut Driver 9. 10mm Open-end Wrench 10. 1/8” straight blade screwdriver 11. T-20 Torx screwdriver 1.4. 1. 2. 3. 4. 1.5. 1. 2. 3. 4. 5. 1.6.
Installation 1.9. ST14 Ku-Band TVRO Running the Cables for Model ST14 D: 1.9.1. Antenna Cable Route the “F” connector end of the antenna cable down from the radome mounting location through the boat to the antenna control panel location. Adjust the cable routing so that about 12 inches (30.5cm) of cable extends beyond the radome mounting surface and about 4 inches (10cm) of cable extending out of the antenna control panel mounting surface. 1.9.2. IF Cables 1.9.2.1.
ST14 Ku-Band TVRO 1.10.2. Installation IF Cables 1.10.2.1. ACP to DeStacker Route the receiver IF cable from the antenna control panel location to the DeStacker mounting location. Leave about 4 inches (10cm) of cable extending out of each mounting location. 1.10.2.1.1. DeStacker to Receiver (1-2 receiver setup only) Route the IF cable(s) from the DeStacker location to the satellite receiver location(s). Leave about 4 inches (10cm) of cable extending out of each mounting location. 1.10.2.1.2.
Installation 1.12. ST14 Ku-Band TVRO Install the Antenna Radome Refer to the Installation Arrangement drawing for mounting dimensions of the radome assembly. Note that the Antenna Radome installation procedure are identical for all ST14 Series Systems. Before performing this procedure, verify all of the system contents with the packing list provided with the shipment.
ST14 Ku-Band TVRO Installation Locate and remove the Azimuth Lock-Down Pin by pulling it straight out. Retain and store this hardware for future use. Using your hand, rotate the antenna in azimuth to align an access hole with a threaded metal radome base mounting insert.
Installation ST14 Ku-Band TVRO NOTE: The Radome Base contains weep holes to allow any water that potentially may enter radome to weep out. Do not confuse these radome “weeping” holes with the actual mounting inserts. Exercise caution as to not allow anything, including the mounting surface, to block these weep holes. A failure to comply with this may result in the accumulation of standing water.
ST14 Ku-Band TVRO 3. Installation Remove the paper backing from the rubber mounting pad. Lift the base of the radome up and install the radome mounting pad as shown to the right.. Lift the base of the radome up and connect the antenna cable to the base of the antenna.
Installation ST14 Ku-Band TVRO Locate and using needle nose pliers, remove the elevation stop pin. Retain and store this hardware for future use. By hand rotate the reflector from Horizon (0˚ Elevation) to Zenith (90˚ Elevation) to ensure full range of motion with no physical obstructions.
ST14 Ku-Band TVRO Installation By hand, rotate the antenna in Azimuth 360˚to ensure full range of motion with no physical obstructions. 1.13. Install the Antenna Control Panel Refer to the Installation Arrangement drawing. Assure that the DC Power Cable is not connected to the DC Supply. 1. At the antenna control panel, connect the red wire to the + (plus) terminal on the green screw terminal. 2. Connect the black wire to the - (minus) terminal on the green screw terminal.
Installation 3. ST14 Ku-Band TVRO Connect the antenna cable to the IN connector of the antenna control panel. This IN connection supplies 30VDC operating voltage and antenna control signals to the antenna and receives satellite signal from the antenna. CAUTION: Connecting the satellite receiver to the IN connector may damage the satellite receiver. 4. Connect the receiver cable to the OUT connector of the antenna control panel.
ST14 Ku-Band TVRO Installation 1.14.2.3.1. Multi-Switch to Slave DiSEqC Switch (multiple receivers) Connect an available output port of the Multiswitch to the Splitter/Multiswitch port of a Slave DiSEqC Switch. Repeat as required for each switch installed. 1.14.2.3.2. Slave DiSEqC Switch to receiver (multiple receivers ) Connect the Receiver (SAT IN) port of a Slave DiSEqC Switch to the satellite in port of a slave satellite receiver. Repeat as required for each receiver installed. 1.14.3.
Installation ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK 1-14
ST14 Ku-Band TVRO 2. Setup for Model ST14 D Setup for Model ST14 D Use this chapter to setup the Model ST14D (DiSEqC) 2.1. 1. 2. 2.2. System Checkout Press the POWER key on the antenna control panel. The display should report model and software versions, verifying the DC power connection between the antenna control panel and the antenna pedestal assembly. Turn power ON to the satellite receiver and the TV monitor.
Setup for Model ST14 D ST14 Ku-Band TVRO DishPro or DishPro Plus Satellite Receiver to determine and target the correct satellite based on the operators channel selection. For integrated Receivers that do support DiSEqC, the ST-14 requires that the user press the NEXT key to determine and target the desired satellite. The Targeting Mode Parameter selection allows the user to configure the systems mode of satellite targeting selection.
ST14 Ku-Band TVRO Setup for Model ST14 D The following table serves as a guide to help properly setup your ST-14. Contact your (prospective) Service Provider to define which satellite(s) are required which is normally based on your service subscription.
Setup for Model ST14 D 2.3.5. ST14 Ku-Band TVRO SAT1 - First Satellite Parameters Access all of the SAT1 individual parameters via a sub menu. Choices are: 2.3.5.1. PRESET This choice presets all of the other sub-menu parameters to factory defaults for the satellite you choose to set this SAT to. 1. Press the NEXT key to select this parameter for adjustment. 2. Once selected, press ▼ & ▲ arrow keys to scroll through a list of choices which this SAT can be preset to.
ST14 Ku-Band TVRO 2.3.5.3. Setup for Model ST14 D LON Enter or edit the Longitude position of this satellite. Range of acceptable values are 0-180, East or West (E or W). 1. Press the NEXT key to select this sub-menu parameter for adjustment. 2. A cursor will appear under the East/West hemisphere character. Press ▼ & ▲arrow keys to set this character to the desired hemisphere (E/W). 3. Press the NEXT key to move the cursor to the number digit to the right.
Setup for Model ST14 D 2.3.5.6. ST14 Ku-Band TVRO FEC Enter or edit the best Forward Error Correction rate for the receiver to use for this satellite. This choice presets all of the other sub-menu parameters to factory defaults for the satellite you choose to set this SAT to. 1. Press the NEXT key to select this parameter for adjustment. 2. Once selected, press ▼ & ▲ arrow keys to scroll through a list of choices which this SAT can be preset to. This list may change in future software revisions.
ST14 Ku-Band TVRO Setup for Model ST14 D 6. 2.3.6. If you do not want to edit any other sub-menu parameters, press SAVE again to exit the sub-menu and return to the SAT main menu display. From there you can press the ▼ arrow key to go to next SAT numeric menu choice or to the Factory Settings menu choice. SAT2 - Second Satellite Parameters Access all of the SAT2 individual parameters via a sub menu.
Setup for Model ST14 D ST14 Ku-Band TVRO NOTE: The Serial Number parameter setting is saved in the PCU, therefore, MUST be set whenever the PCU is changed. After this parameter has been set correctly, it must be SAVED in the PCU. 1. Press the NEXT key to SELECT this sub-menu parameter for adjustment. 2. A cursor will appear under the rightmost digit. Press ▼ & ▲ arrow keys to increment/decrement this digit. 3. Press the NEXT key to move the cursor to the digit to the left.
ST14 Ku-Band TVRO Setup for Model ST14 D 2.3.11.4. LON (Ships Longitude) This parameter is automatically set by the GPS antenna mounted on the Coastal pedestal inside the radome. The GPS input enables the antenna to quickly & accurately target satellites (SAT1 – SAT6). 1. Press the NEXT key to select this sub-menu parameter for adjustment. 2. A cursor will appear under the rightmost digit. Press ▼ & ▲ arrow keys to increment/decrement this digit. 3.
Setup for Model ST14 D ST14 Ku-Band TVRO system will use the parameter entered for MID LAT OFFSET for calculating the tracking threshold. 2.3.11.5.3. Upper Latitude Range The HIGH LAT LIM parameter defines the “Upper” Latitude Limitation Range and is any whole degree from1-90. The HIGH LAT LIM parameter sets the lowest latitude position of the Upper latitude range. Therefore the upper latitude range will be any latitude range from HIGH LAT LIM to 90°.
ST14 Ku-Band TVRO Setup for Model ST14 D 4. 5. Press the NEXT key to move the cursor to the next digit to the left. Press ▼ & ▲ arrow keys to increment/decrement this digit. Press the SAVE key to save this parameter to memory. 2.3.11.6.3. HIGH LAT OFFSET The HIGH LAT OFFS parameter defines what threshold offset value parameter is used when the vessel is located within the Upper Latitude Range. 1. Press the NEXT key to select this sub-menu parameter for adjustment. 2.
Setup for Model ST14 D ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK 2-12
ST14 Ku-Band TVRO 3. Setup for Model ST14M Setup for Model ST14M 3.1. 1. 2. 3.2. System Checkout Press the POWER key on the antenna control panel. The display should report model and software versions, verifying the DC power connection between the antenna control panel and the antenna pedestal assembly. Turn power ON to the satellite receiver and the TV monitor. The television may now be displaying “searching for satellite signal” verifying proper video connections between the receiver and the monitor.
Setup for Model ST14M • ST14 Ku-Band TVRO MANUAL TARGET: Intended Use: Single or multi-satellite tracking requirement. Description: By selecting this mode of manual operation the antenna will not automatically target any satellite preset regardless of any received commands that may be sent by the satellite receiver to do so. In this mode the user is required to manually target the desired satellite by pressing the NEXT key to select the appropriate Preset (i.e.
ST14 Ku-Band TVRO Setup for Model ST14M Empty 3. 4. 5. Blanks/zeroes all parameters for this satellite, so switching satellites (NEXT) will skip over the satellites you don’t want (if you only use ONE satellite, you should preset all of the other SAT selections to be empty/blank). ExpV82 Bell ExpressVu @ 82W ExpV91 Bell ExpressVu @ 91W DTV 72 DirecTV @ 72W DTV101 DirecTV @ 101W DTV110 DirecTV @ 110.
Setup for Model ST14M 5. 6. ST14 Ku-Band TVRO If you want to edit any of the other default values that are loaded with preset, press the ▼ arrow key to go to the next sub-menu parameter. If you do not want to edit any other sub-menu parameters, press SAVE again to exit the sub-menu and return to the SAT main menu display. From there you can press the ▼ arrow key to go to next SAT numeric menu choice or to the Factory Settings menu choice. 3.3.4.4.
ST14 Ku-Band TVRO Setup for Model ST14M 7/8 SCPC AUTO* 3. 4. 5. Automatically scans through all the available forced * (star’ed) FEC rates. If the satellite does not generate an NID but does have a unique combination of FREQ, BAUD and FEC lock, select the appropriate FEC* choice from this list. The system will then generate its own unique forced NID to represent the desired satellite. You will need to enter this pseudo NID in the NID setting below.
Setup for Model ST14M ST14 Ku-Band TVRO paragraphs to set PRESET, NAME, LON, RHCP freq, BAUD, FEC, and NID for a third satellite that you wish to use periodically. 3.3.7. SAT4 - Fourth Satellite Parameters Access all of the SAT4 individual parameters via a sub menu. If a forth SAVED satellite is not needed, preset SAT4 to empty/blank so NEXT will skip over this selection when you are switching satellites.
ST14 Ku-Band TVRO Setup for Model ST14M 3.3.10.2. MODEL CONFIGURATION This parameter sets all of the internal drive, scale factor and limits for the motors, gear ratios and sensors FOR THIS MODEL ANTENNA. NOTE: The MODEL parameter setting is saved in the PCU, therefore, MUST be set whenever the PCU is changed. WARNING: Improper setting of this parameter WILL cause the antenna to malfunction. 1. 2. 3. 4. Press the NEXT key to select this sub-menu parameter for adjustment.
Setup for Model ST14M ST14 Ku-Band TVRO 3.3.11.1. Latitude Ranges: The three latitude ranges in the “LAT-THRESH OFFSET TABLE” are defined by setting 2 system parameters, “Low Lat Lim” and “High Lat Lim”. 3.3.11.1.1. Lower Latitude Range The LOW LAT LIM parameter defines the “Lower” Latitude Limitation Range and is entered using any whole degree from 0-90. The LOW LAT LIM parameter sets the highest latitude position of the lower latitude range.
ST14 Ku-Band TVRO Setup for Model ST14M 3.3.11.2. LOW/MID/HI LAT OFFSET (Threshold Offset) The threshold-offset parameters are an AGC value from 0-255 that is summed to the average noise floor, to properly calculate the systems tracking signal threshold every time the system is commanded to Target or Search for a desired satellite.
Setup for Model ST14M ST14 Ku-Band TVRO 5. Press the SAVE key to save this parameter to memory To operate the system in the mode previously known as Auto Threshold set all three threshold offset parameters to the same value, thereby using the same Thresh Offset parameter value regardless of the vessels Geo Location. 3.4.
ST14 Ku-Band TVRO 4. Setup for Model ST14E Setup for Model ST14E 4.1. 1. 2. 4.2. System Checkout Press the POWER key on the antenna control panel. The display should report model and software versions, verifying the DC power connection between the antenna control panel and the antenna pedestal assembly. Turn power ON to the satellite receiver and the TV monitor. The television may now be displaying “searching for satellite signal” verifying proper video connections between the receiver and the monitor.
Setup for Model ST14E 6. 4.3.3. ST14 Ku-Band TVRO Press the ▼ arrow key to go to the next parameter. SATA - First Satellite Parameters Access all of the SATA individual parameters via a sub menu. Choices are: 4.3.3.1. PRESET This choice presets all of the other sub-menu parameters to factory defaults for the satellite you choose to set this SAT to. 1. Press the NEXT key to select this parameter for adjustment. 2.
ST14 Ku-Band TVRO Setup for Model ST14E 4. 5. 6. Continue editing until all 3 digits have been set to the Longitude (0-180) position of this satellite selection. Press the SAVE key to save the LON parameter for this SAT. If you want to edit any of the other default values that are loaded with preset, press the ▼ arrow key to go to the next sub-menu parameter. If you do not want to edit any other sub-menu parameters, press SAVE again to exit the sub-menu and return to the SAT main menu display.
Setup for Model ST14E ST14 Ku-Band TVRO If you do not want to edit any other sub-menu parameters, press SAVE again to exit the submenu and return to the SAT main menu display. From there you can press the ▼ arrow key to go to next SAT numeric menu choice or to the Factory Settings menu choice. 4.3.3.7. Hi Band Horizontal Frequency Enter or edit the Ku Hi Band Horizontal Frequency (in MHz) for the receiver to use to track this satellite. Range of acceptable frequency input is 950-2150 MHz. 1.
ST14 Ku-Band TVRO 4.3.3.10. Setup for Model ST14E Lo Band FEC Rate Enter or edit the Lo Band Forward Error Correction rate for the receiver to use for this satellite. This choice presets all of the other sub-menu parameters to factory defaults for the satellite you choose to set this SAT to. 1. Press the NEXT key to select this parameter for adjustment. 2. Once selected, press ▼ & ▲ arrow keys to scroll through a list of choices which this SAT can be preset to.
Setup for Model ST14E ST14 Ku-Band TVRO AUTO* 3. 4. 5. Automatically scans through all the available forced * (star’ed) FEC rates. If the satellite does not generate an NID but does have a unique combination of FREQ, BAUD and FEC lock, select the appropriate FEC* choice from this list. The system will then generate its own unique forced NID to represent the desired satellite. You will need to enter this pseudo NID in the NID setting below.
ST14 Ku-Band TVRO 4.3.4. Setup for Model ST14E SATB - Second Satellite Parameters Access all of the SATB individual parameters via a sub menu. If a second SAVED satellite is not needed, preset SATB to “Empty” so when the NEXT key is pressed the antenna will not search for any unwanted satellite(s) All of the SATB parameters are set exactly the same way that the SATA parameters were set, but would be set to different choices.
Setup for Model ST14E ST14 Ku-Band TVRO 2. 3. 4. 5. 4.3.6.4. 1. Press the NEXT key to SELECT this sub-menu parameter for adjustment. A cursor will appear under the leftmost digit. Press ▼ & ▲ arrow keys to increment/decrement this digit. Press the NEXT key to move the cursor to the next digit to the right. Press▼ & ▲arrow keys to increment/decrement this digit. Press the NEXT key to move the cursor to the next character to the right.
ST14 Ku-Band TVRO 5. Maintenance Maintenance 5.1. Warranty Information Sea Tel Inc. supports its Coastal Series systems with a warranty program unsurpassed in the industry. These systems are backed by a TWO YEAR full warranty on parts and a ONE YEAR warranty on labor.
Maintenance 5.3. ST14 Ku-Band TVRO Replacing an LNB Follow the procedure below to install a Ku-Band circular receive DLA LNB Sea Tel P/N 115075-2. Unless otherwise noted, apply adhesive to all hardware per Sea Tel Specification Document 121730 1. Turn the power Off to the Antenna 2. Remove radome top. You may need to rotate the antenna to gain access the back of the reflector. 3. Using a 7/16” Wrench, remove the Coax(es) connected to the LNB.
ST14 Ku-Band TVRO 4. 5. 6. Maintenance Using a Phillips head screw driver, remove the screws that secure the LNB to the reflector assembly. Remove LNB and place aside. Install replacement LNB into mounting collar as secure using the screws that were loosened in step 4.
Maintenance 7. 5.4. ST14 Ku-Band TVRO Reconnect and secure coax(es) removed earlier. Preventive Maintenance As needed - Clean the outside surface of the radome with warm soapy water to remove dust, grime and salt residue. There is no other preventive maintenance required 5.5. Fault Isolation/Trouble-shooting The following table is provided to help isolate problems in the Coastal Series Antenna system. Symptom Possible Fault Antenna tracking but receiver not providing desired programming 1. 2.
ST14 Ku-Band TVRO Antenna does not come on when the ON key is pressed Maintenance 1. 2. 4. 1. 2. 3. 4. 5. 6. 1. 2. 1. Check +12 VDC input to antenna control panel. Verify that all connections on the rear of the antenna control panel are properly seated.
Maintenance ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK 5-6
ST14 Ku-Band TVRO 6. ST 14 Technical Specifications ST 14 Technical Specifications 6.1. Installed Weight Total Weight (dry): 6.2. Radome Diameter Height Mounting 6.3. Spun Aluminum reflector 14.5 inch (36.8cm) Cassegrain feed with center focus splash plate Circular ONLY 50 dB US Circular LNB Antenna C14E/ST14E Type Size Feed Polarization Min EIRP LNB 6.5. 16.5 inch (41.9cm) 18 inch (45.7cm) Qty 4 6mm x 1.0 fasteners Antenna C14(M/D)/ST14(M/D) Type Size Feed Polarization Min EIRP LNB 6.4.
ST 14 Technical Specifications Elevation Pointing +/- 15 degrees of Roll +/- 25 degrees of Roll 6.6. 35 to 60 degrees 40 to 50 degrees US Circular LNB Sea Tel Part Number: Type: LNB Manufacturer: RF Frequencies: IF Frequency: LO Frequency: Noise Figure: Polarization modes: Polarization control: 6.7. ST14 Ku-Band TVRO 127444-1 Dual output CAL AMP, but may vary 12.2 - 12.7 GHz 950 - 1450 MHz 11.250 GHz 1.1 dB max.
ST14 Ku-Band TVRO 6.7.2. ST 14 Technical Specifications Pedestal Control Unit Features Fully integrated controller, sensors, motor drivers, and RF signal Tracking Receiver. 10” x 12 ½” x 2 1/2” Size 6.7.3. DVB Compliant Tracking Receiver Internal Satellite Identification Receiver Tuning range Input RF Level Output RF Level Sensitivity Bandwidth Satellite ID QPSK Demodulator FEC Decoder Pipeline Decoder 6.8.
ST 14 Technical Specifications ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK 6-4
ST14 Ku-Band TVRO 7. Computer Interface Computer Interface A computer may be connected to the antenna control panel (via a 9 pin serial cable) to allow you to perform software updates to the system, This connection may also provide access to ALL the parameter settings and to query the Coastal Series antenna and view the responses it provides. The commands to set the parameters in the Coastal Series PCU are summarized below.
Computer Interface ST14 Ku-Band TVRO y2nnn Set Mid Lat. THRESHOLD OFFSET in AGC counts (0-255) y3nnn Set High Lat. THRESHOLD OFFSET in AGC counts (0-255) +/- inc / dec pol trim. C Tracking / DishScan ON. D Tracking / DishScan OFF, Search OFF. F Update current sat as last viewed in flash. N Select next visible satellite. W Write parameters to NVRAM. U Y Z 8/2 6/4 3/1 7 9 ^0005 ^0009 ^000[4/6] ^000[8/2] [ Pt Force Unwrap. Restore DACP operation.
ST14 Ku-Band TVRO 7.1.1. Computer Interface Programming Instructions Coastal Series Pedestal Control Unit These instructions apply to the Coastal Series antennas. Electrical Hookup – Coastal ACP 1. Use a standard straight 9-pin serial cable (P/N 120643 or equiv.) connected between the ACP (M&C Port) and a PC with an available com port. 2. 3. Obtain a Copy of the PCU .s19 file and save in a convenient area such as the desktop or in the same directory as the ProgTerm files. 4.
Computer Interface 6. ST14 Ku-Band TVRO 8. From the “CommPort” menu, select “Properties”. Verify the correct COM port is selected. Select correct Maximum Speed (9600 for Coastal Series). Press “OK” to confirm any changes. 9. Power on ACP 7. 10. Click on the Paper Clip button and then click on the EyeBall button in the tool bar. This queries the Module Status and Module Version. The responses will be the Antenna Serial Number and Software Version in the PCU (such as “Coastal Ver. 208”).
ST14 Ku-Band TVRO Computer Interface 13. Press ‘UPLOAD’ to begin sending the new hex file program update to the ACU module. A dialog box will appear to allow you to select the file to be programmed. 14. Program Terminal will send the new file to the desired module and you will see an Upload dialog box with a “Cancel” button. After the programming is complete, the pedestal will reinitialize.
Computer Interface ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK 7-6
ST14 Ku-Band TVRO 8. Drawings Drawings The following drawings are included with this manual for installation and maintenance reference. 8.1.
Drawings ST14 Ku-Band TVRO THIS PAGE INTENTIONALLY LEFT BLANK 8-2
8 6 7 4 5 3 NOTES: 1 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. REVISIONS DESCRIPTION LTR 19 UNLESS OTHERWISE SPECIFIED. 2X 18 3X 14 F 34 A B C 35 APPROVAL DATE RELEASED DRAWING REF ECN 09-038 REF ECN 09-068 MN 03/24/09 DH 04/03/09 06/04/09 DH 06/09/09 1.
8 6 7 4 5 3 1 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED.
8 7 6 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. LTR 8 2X 10 17 11 1.
8 7 6 4 5 NOTES: F 1. 1 2 3 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. REVISIONS LTR 7 UNLESS OTHERWISE SPECIFIED.
8 7 6 4 5 1 2 3 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. REVISIONS LTR NOTES: UNLESS OTHERWISE SPECIFIED. 1.
8 7 6 4 5 1 2 3 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. REVISIONS LTR NOTES: UNLESS OTHERWISE SPECIFIED. 1.
8 6 7 4 5 3 NOTES: 1 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. REVISIONS DESCRIPTION LTR 3X 14 UNLESS OTHERWISE SPECIFIED. 2X 17 F 1. ASSEMBLE PER AI ST129279.
8 6 7 4 5 3 1 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED.
8 7 6 4 5 NOTES: REVISIONS LTR 7 UNLESS OTHERWISE SPECIFIED. F 1 2 3 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. 4X D ESCRIPTION A RELEASED DRAWING B REF ECN 09-113 MN DATE APPROVAL 5/12/09 DH 05/12/09 F 1.
8 7 6 4 5 1 2 3 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED.
8 6 7 4 5 3 NOTES: 1 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. REVISIONS DESCRIPTION LTR 3X 14 UNLESS OTHERWISE SPECIFIED. 2X 17 F 1.
8 6 7 4 5 3 1 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED.
8 7 6 F 1 2 3 REVISIONS 7 NOTES: 4 5 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Comant Industries, inc. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF Comant Industries, inc. IS PROHIBITED. LTR 4X 4X 6 UNLESS OTHERWISE SPECIFIED. 1. ASSEMBLE PER AI ST129285-1 2 USE HARDWARE SUPPLIED WITH ITEM 5.
