User's Manual

ManualsBrandsSDR Electronics ManualsElectronics4045-TRPAUTOS

quick start guide

Troubleshooting

Problems? No problem. Check these tips for a quick fix:

FM Radio

1. On?

2. Tuned to unused frequency?

3. Radio volume adjusted?

iTrip

1. Has iTrip gone in low power mode? iTrip goes in a

power-saver mode after an extended period of no music.

To get the music going again, just press Play on your iPod,

or disconnect and reconnect iTrip to your iPod.

2. iTrip and radio frequencies match?

iPod

1. Hold switch on?

2. Play button depressed?

3. Battery completely drained? If so, your iPod must

recharge for a few short minutes before so your iPod

will sense a constant current and power up.

Fuses

1. Car's Cigarette Lighter fuse good? (Consult your car's

owners manual for fuse locations and specifications)

2. iTrip Auto's fuse blown? Check the replaceable fuse located

near the front of the unit. An automotive blade-type mini

fuse (sometimes called an ATM fuse) rated at 2 Amps can

be obtained at most auto or hardware supply stores.

Problem's not solved? No problem.

Call Griffin's Customer Support at 800-208-5996.

Monday - Thursday 9 am - 6 pm and Friday 9am - 5pm Central time.

Your call will be answered by real human beings who actually know

and use Griffin products.

Griffin stands behind every product with the industry’s best customer service, backed by a simple, fair warranty.

Please read our warranty details at www.griffintechnology.com/support/ before using this Griffin product.

and iTrip is a registered trademark of Griffin Technology, Inc. • iPod is a trademark of Apple Inc., registered in the U.S.

and other countries. • Patents pending • Made in China • Designed in Tennessee

Technical Specifications

Built for iPod models that use the

full-size Dock Connector

Transmitter Dimensions: 2.2” L x 1.02“ D x .43” H

( 58mm L x 26mm D x 11mm H)

Total Length: 44.5” (115.6cm)

Weight: 56g

Antenna: Built-in

Power: Provided by 12 Volt cigarette lighter

or power outlet (no batteries required)

Input voltage range: 12 – 16 Volts DC

Maximum current: 2 Amp

Output voltage: 5.2 Volts DC at 1 Amp

Fuse type: 2 Amp blade-type automotive fuse

Modulation: FM Stereo

Available output RF ranges (region preset at factory):

U.S.: 88.1 MHz ± 107.9 MHz

Japan: 76.0 MHz ± 90.0 MHz

Other Countries: 88.0 MHz ± 108.0 MHz

Radio Frequency Adjustment Increments:

Japan: 0.1 MHz per step

U.S. and Other Countries: 0.2 MHz per step

Radio Frequency Response: 50 Hz ± 15 kHz

Operating Range: 10 – 30 feet (~3m-9.1m)

itripautoQS2 ipod.ai

8/14/07 1230pm

Using Other Frequencies

In areas with numerous overlapping radio

stations, you may need to switch frequencies

to get the best possible sound, depending

on your location. Here’s how:

Using the presets

1. Press FUNCTION—>PRESET

Select any of the three saved presets.

(iTrip will exit this menu automatically

after about 3 seconds.)

2. Tune your car’s FM radio to the new

frequency displayed on iTrip’s screen.

Tuning Manually

Manual tuning is a reverse of the SmartScan

process; you tune your car stereo first, then

adjust iTrip to match that frequency.

1. On your car’s FM radio, select a frequency

on which you hear nothing but static. The

ideal choice would have nothing on either

of the neighboring frequencies, so listen

for 3 in a row with static and select the

middle frequency.

2. Press + or – to set iTrip to match that

frequency. Press the + or – and hold to

move through the frequencies quickly.

Setting your own presets

Do you have a long commute that has you hunting

frequencies as radio stations fade in and out of range?

Or are you a long-time iTrip user who already knows

the perfect three frequencies? Either way, iTrip lets

you set your own presets for quick recall.

1. Tune your iTrip to the desired frequency.

2. Press FUNCTION—>PRESET

(iTrip will automatically exit this menu

after about 3 seconds.)

3. Press and hold PRESET 1, PRESET 2 or

PRESET 3 for 2 seconds. Screen blinks

once and the selected PRESET button lights

to indicate that it is stored successfully.

Stereo or Mono for Best Sound

Press FUNCTION—>MODE—>MONO

(Broadcasts in mono, resulting in a

stronger signal than stereo.)

Use for podcasts, talk radio, audiobooks

and similar tracks.

Use in heavily populated areas where

numerous FM stations crowd the dial.

Press FUNCTION—>MODE—>STEREO

(Broadcasts in stereo, for more realistic audio.)

Use for music and musical podcasts.

Use for best possible Right/Left Channel

stereo separation.

-OR-

Scanning

91.9

Preset ModeScan

106.9

91.9

2 3

Function

106.9

Preset ModeScan

106.9

Function

106.9

Preset ModeScan

106.9

Function

106.9

Preset ModeScan

106.9

Stereo

Mono

106.9

Function

106.9

FUSE

automotive

blade type-2

106.9

Mono

Stereo

iTrip

"Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has

been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation

of this device or its compliance with safety and regulatory standards.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

Griffin Technology

4045-TRPAUTOS

The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications

to this equipment. Such modifications could void the user’s authority to operate the equipment.

Thanks for purchasing Griffin Technology’s

iTrip Auto with SmartScan.

The easiest way to charge and play in your car.

SmartScan finds and saves the best frequencies

to play your iPod on your car's FM stereo.

Connect

1. Connect iTrip Auto's Dock Connector

to your iPod.

2. Plug the cigarette lighter adapter into your

car’s cigarette lighter or power outlet. This

will power your iTrip Auto and charge your

iPod at the same time.

Charge

3-stage Light Ring

Red LED is on: iTrip is correctly plugged

in, ready to charge your iPod and operate

the iTrip transmitter.

Amber LED is on: iTrip is charging your iPod

and is providing power to iTrip’s FM transmitter.

Green LED is on: Your iPod is fully charged

and there is power to iTrip’s FM transmitter.

™

Auto

™

Auto

Play

iTrip Auto with SmartScan makes playing your iPod on your car stereo

easier than ever. Here’s how to make it happen:

SmartScan for Clear Frequencies

1. Press FUNCTION —> SCAN

SmartScan scans all available FM frequencies and saves the 3 clearest

frequencies to iTrip’s 3 presets. SmartScan takes about 25 seconds to

complete the process, then automatically chooses the clearest frequency

and displays it on iTrip’s high-contrast OLED display.

2. Set your FM stereo

Tune your car’s FM radio to the

frequency displayed on iTrip’s screen.

3. Play your iPod

Press Play and enjoy the music.

Auto

2 1