iBT230 Eng IB Size: 153mm x 120mm Printing color: Black Nov 4, 2014 P1 Model: iBT230 Bluetooth Wireless FM Clock Radio with USB Charging instruction manual Questions? Contact Customer Service at 1-800-288-2792
P2 iBT230 Introduction Thank you for purchasing the iHome iBT230. This product is designed to provide high quality wireless sound for your iPad, iPhone, iPod or other Bluetooth audio device. This instruction booklet explains the basic operation and care of the unit. Please read it carefully and keep for future reference. Maintenance • Place the unit on a level surface away from sources of direct sunlight or excessive heat.
P3 iBT230 Table of Contents What’s Included ...............................................................................................................3 Meet Your iBT230 ............................................................................................................4 The Display/Setting Up the Unit ..........................................................................................5 Replacing/Installing Backup Batteries ...............................................................
P4 iBT230 What’s Included • iBT230 system • 100V-240V universal AC adaptor • Stereo audio cable pair audio cable iBT230 power adaptor 3
P5 iBT230 Meet Your iBT230 Top Mode Button Sleep/Clock Adjust Button Presets Button Alarm 1 Button Alarm 2 Button Power/ Alarm Reset Button Volume Down/ Volume Up Buttons Answer Call/ Plus Settings Button pair End Call/ Minus Settings Button Play/Pause/Pairing Button Snooze/Display Dimmer Button Bottom Back Aux-in Jack DC Jack DC 5V 2A Backup Battery Compartment FM Antenna 4 USB Charging Port
P6 Using the The Display iBT230 Time Display PM/AM Indicators Aux-in Mode Indicator Set Wake-to Sleep Mode Indicator FM Radio Mode Indicator Alarm Active Indicator Low Backup Battery Indicator Bluetooth/Pairing Indicator Alarm Time/Date/Radio Frequency Wake to source: BT (Bluetooth), FM Radio, Buzzer Mode: BT (Bluetooth), FM Radio, Aux Setting Up the Unit Connect the included AC adaptor to the DC jack located on the back of the unit and connect the other end to a working wall outlet.
P7 Using the iBT230 Replacing and Installing Clock Backup Batteries Note: 2 AA batteries are included with the unit. Install them before using the unit. This model is equipped with a battery backup circuit that will maintain the time and alarm time settings in the event of a temporary power interruption (the display is NOT maintained). The battery backup circuit will also operate the buzzer alarm to wake you up at the selected wake up time even if the power is out.
P8 Using the Setting the Clock iBT230 1. Press and hold the Sleep/Clock Adjust Button for 2 seconds until the clock display flashes and a beep sounds. 2. Press the or Buttons to adjust the clock to the current time (hold for rapid setting). Make sure you set the correct AM/PM time. The AM and PM indicators appear to the left of the display. 3. Press the Sleep/Clock Adjust Button to confirm the time. The year will flash on the display. 4.
P9 Setting and Using the Alarms (Continued) Using the iBT230 1. Press and hold the Alarm Button for 2 seconds until the alarm time display and alarm icon flash. A beep sounds. 2. Press the or Buttons to adjust the alarm time to the desired time (hold for rapid setting). Make sure you set the correct AM/PM alarm time. The AM and PM indicators appear to the left of the display. 3. Press the Alarm Button to confirm the alarm time setting. The wake-to source will flash. 4.
P10 Using the Snooze/Display Dimmer Button iBT230 1. To program Snooze, press and hold the Snooze/Display Dimmer Button during normal operation (when no alarm is sounding). 2. Press the or Buttons to select the desired snooze time (between 01 and 29 minutes). 3. Press and release the Snooze/Display Dimmer Button to confirm Snooze setting. 2 beeps will sound. 4.
P11 Using the Setting and Using FM Presets iBT230 The unit allows you to store up to 6 FM radio station presets 1. Press and release the Mode Button as needed until the FM indicator icon appears on the display. 2. Press and release the Presets Button as needed until the preset number (P1- P6) you wish to set is displayed, then press and hold the Presets Button to enter setting mode. 3. Press the or Buttons to tune the radio to the desired station (hold to scan for the next clear station). 4.
P12 Using the iBT230 Pairing Your Bluetooth Device Whenever AC power is connected, the iBT230 will attempt to autolink to a previously paired device. If no device is paired, the iBT230 will automatically enter pairing mode for 2 minutes. You can manually initiate pairing without turning on the iBT230 by following steps 1-3 below. 1. Make sure your Bluetooth device is fully charged. Turn on your Bluetooth device and make it “discoverable” by turning on Bluetooth mode (check in Options or Settings) . 2.
P13 Using the Playing Audio Via Bluetooth iBT230 1. Press the Power/Alarm Reset Button to turn the unit ON. 2. Press and release the Mode Button as needed until the BT and the Bluetooth icon appears on the display. 3. Press the Play/Pause/Pairing Button on the unit to play audio from your linked Bluetooth device. 4. Press the or Buttons to go to the previous or next track. 5. Press the or Buttons to adjust the volume on the unit. 6.
P14 Using the Playing Audio via Aux-In iBT230 1. Connect one end of the included standard stereo 3.5mm audio cable into the aux-in jack on 2. 3. 4. 5. 6. the back of the unit and the other end into the headphone or output jack of your audio device. Press the Power/Alarm Reset Button on the unit to turn it on. Press and release the Mode Button as needed until the AUX indicator icon appears on the display. Place your audio device in play mode. Navigate tracks and adjust output volume on the device.
P15 Using the Charging Devices via USB Port iBT230 1. Connect the standard size end of a USB cable (not included) to the USB Port on back of the unit and connect the other end to the charging port on your device. 2. Monitor the charging on your device. Some devices use a proprietary charging method and will not charge using the USB Port. If this happens, you must charge your device using the charger that came with it.
P16 Battery Use Cautions and Tips • Only use the recommended/supplied batteries or equivalent • Use alkaline batteries for longer life • Do not mix old and new batteries, and do not mix alkaline, carbon-zinc or rechargeable nickel-cadmium batteries • Insert batteries with proper polarity (+/–) as indicated • Remove exhausted batteries from product • Recharge rechargeable batteries under adult supervision • Do not attempt to recharge non-rechargeable batteries • Do not o pen batteries or heat them beyond no
P17 Consumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
P18 iBT230 FCC Information FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. FCC ID: EMOIBT230 IC: 986B-IBT230 This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
P19 Troubleshooting Unit doesn’t respond (no power) • • • Check that all connections are correct and properly plugged in. Make sure your device is properly paired with the iBT230. Make sure the Power is ON. Unit doesn’t respond (locked up or frozen) • The unit may need to be reset. To do so, unplug the unit from power source and remove the backup batteries. Let unit stand for 2 minutes. Re-install backup batteries and connect unit to power source.
P20 Limited 1 Year Warranty iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.