QUICK START GUIDE (407) 774-2447 / www.sctflash.
SECTION 1: PARTS + CHECKLIST X4 DEVICE MICRO USB™ CABLE HDMI/OBD II CABLE TOOLS NEEDED: Fuse Puller | Voltage Tester | Battery Charger | Pliers
SECTION 2: PRE-INSTALL CHECKLIST BUSINESS HOURS Technical Support is available Monday – Friday between the hours of 9am and 6pm EST and can be contacted via phone at (407) 774-2447 or through live chat at www.sctflash.com. If you need to contact Tech Support, please be sure to have your device with you before initiating contact. INTERNET ACCESS In the unlikely event that technical support is needed, Internet access may be required to troubleshoot.
SECTION 3: IMPORTANT ON-DEVICE INFO. From the Main Menu, select Device Info. MAIN MENU PROGRAM VEHICLE GAUGES / DATALOG VEHICLE DIAGNOSTICS VEHICLE INFO DEVICE INFO DEVICE SETTINGS Within Device Info, you will find : SERIAL NUMBER: Needed for dealers to create custom tunes for your vehicle and device. FIRMWARE VERSION: This is essentially your device’s operating system. TUNE REVISION The version number of your preloaded tunes. UNLOCKS LEFT: Number of unlocks remaining.
SECTION 4: UPDATING YOUR X4 DEVICE INSTALLING THE UPDATE SOFTWARE NOTE: Make sure the X4 is unplugged from your computer before starting this process. 1. Go to www.sctflash.com 2. Click “Tech Support” tab at the top of the page. 4. Click the “Download Now” button to the left of the listing that reads “SCT X4 Power Flash Programmer Device Update Software.Wait for that program to download, then double click and “Run” the SCTDeviceUpdater.exe file if it does not open automatically. 3. 5. 6. 7.
SECTION 5: READING VEHICLE VIN & STRATEGY/OS PART#’S MAIN MENU PROGRAM VEHICLE GAUGES / DATALOG VEHICLE DIAGNOSTICS VEHICLE INFO DEVICE INFO From the Main Menu, select Vehicle Info. You’ll be asked to turn the key on. The VIN and if a Ford vehicle/device, it will give you the Strategy. If using a GM vehicle/ device, it will give you the OS Part Numbers. DEVICE SETTINGS SECTION 6: CHECKING/CLEARING VEHICLE TROUBLE CODES From the Main Menu, select Vehicle Diagnostics.
SECTION 7: PROGRAMMING THE VEHICLE POWERING ON THE X4 To power up your device, using the provided HDMI to OBDII cable, connect to the vehicle’s OBDII port. The OBDII port is most commonly found within 24” of the steering column under the driver’s side dash.
BEGIN PROGRAMMING 1. From the Main Menu, select Program Vehicle. 2. At this point, the key should be in the ignition, but in the OFF position until prompted to turn key ON. Within Program Vehicle, there are 2-3 selections depending on the state of the vehicle. MAIN MENU PROGRAM VEHICLE GAUGES / DATALOG VEHICLE DIAGNOSTICS VEHICLE INFO DEVICE INFO DEVICE SETTINGS • Pre-Loaded Tune Files = Preloaded SCT tunes for use on stock vehicles only.
USING PRE-LOADED TUNE FILES Once you follow the first “Key On” prompt, the device will show you a selection of vehicles and engine sizes. Select yours here. This will take you to Adjustable Options where you will be able to adjust to different performance levels, vehicle characteristics, and options including, but not limited to, speed limiters, axle ratio and tire size. (Adjustable Options are vehicle specific.
SECTION 8: LOADING CUSTOM TUNES Download and install the SCT Device Updater software and Drivers from : http://sctflash.com/software/SCTDeviceUpdater.exe 1. From your e-mail, save your custom tunes (.cef files) to your computer’s Desktop. 2. Open the SCT Device Updater software and click the Load Custom Tune File button. 3. Click Browse and locate your custom tunes on your Desktop. Alternatively, click Locate Custom Tunes. 4. Select the Tune you wish to load. 5.
NOTE: If you can’t display a specific value from the preloaded config files, you can download Livelink software for free from the SCT website SECTION 9: ON–DEVICE DATA LOGGING 1. Connect the X4 to the OBDII port. 2. From the Main Menu, scroll to Gauges/Datalog and press the center button on the X4. 3. On initial setup, you will need to move to Configuration, press the center button, and select your vehicle from a list of data log files.
SECTION 10: ADJUSTABLE OPTIONS EXPLAINED DIESEL VEHICLE SPECIFIC OPTIONS Performance The most aggressive preloaded diesel tune. Good for everyday use, racing, or economy but not recommended for any type of towing. Street Less power than Performance. Moderate gain over stock, safe for light towing, under 5,000 lbs. Towing Should be used when towing any significant load. Shifting is towing centered. Trans Only For Heavy Loads. Engine and boost left stock. Trans Only tune.
DIESEL & GAS VEHICLE OPTIONS: EGR Delete Removes the check engine light from deleting EGR mechanically. Axle Ratio Sets axle ratio to correct shift patterns/speedo. (Not available on all vehicles) Tire Size Sets tire size to correct shift patterns/speedo. (Not available on all vehicles) Idle Speed Sets idle speed in RPM. Traction Control On/Off setting disables traction control without using the TCS button. WOT Shift Increase or Decrease the WOT Shift points of each gear individually by MPH.
GAS VEHICLE SPECIFIC OPTIONS: Tune Type Performance levels vary by the octane you select. Higher octane will provide higher performance increase. 93 octane would be the highest increase. Towing Tune Adjusts the octane based tunes to focus more on towing over performance. Economy Tune Adjusts the octane based tunes to focus more on economy over performance. Rear O2s Disables the rear O2s and eliminated the CEL caused by rear O2 removal. Global Spark Add or remove timing advance to the entire RPM range.
GAS VEHICLE SPECIFIC OPTIONS: CMCV Deletes Updates tune to handle the CMCV/IMRC delete plates modification. Fan Control Lowers the temperature at which the fan turns on. Rev Limiter Drive Sets rev limit in RPM while in drive. Rev Limiter Neutral Sets rev limit in RPM while in neutral. Speed Limit remove, increase, or decrease the vehicle speed limiter. (AKA Governor) (407) 774-2447 / www.sctflash.com.
SCT PERFORMANCE, LLC.
SCT PERFORMANCE, LLC. *This product is not legal for sale or use in California on pollution controlled motor vehicles IMPORTANT NOTES It is always a good idea to turn-off any vehicle systems that may become active during the tuning process such as cooling fans, fuel pumps, etc. to avoid draining the vehicle’s battery. To disable these functions, consult your vehicle’s owner’s manual and remove the fuse for each of these systems. Also be sure to turn-off the vehicle's stereo and HVAC system.
SCT PERFORMANCE, LLC. USER'S MANUAL TABLE OF CONTENTS 1. GENERAL INFORMATION ........................................................................................................... 1.1 SCT, LLC Limited Warranty and Disclaimer of Liability ..................................................... 1.2 Device Firmware & Tune Revision Updates............................................................................. 1.3 About Your SCT Device .............................................................
SCT PERFORMANCE, LLC. 1. GENERAL INFORMATION 1.1 SCT Performance, LLC Limited Warranty for X4 What Does This Warranty Cover? This warranty covers any defects or malfunctions in your SCT tuning product within the warranty period set forth below, subject to the following conditions and limitations.
SCT PERFORMANCE, LLC. DISCLAIMER OF LIABILITY THIS IS A HIGH PERFORMANCE PRODUCT. USE AT YOUR OWN RISK. Do not use the X4 product (the “Product”) until you (the “Buyer”) have carefully read this Disclaimer of Liability (this “Disclaimer”). The installation and use of this Product indicates that you have read and understand, and accept all of the following terms of, this Disclaimer: SCT Performance, LLC (the “Seller”), shall not be responsible for the Product’s proper installation, use and service.
SCT PERFORMANCE, LLC. 1.2 Device Firmware & Tune Revision Updates From time to time, you may wish to update your device to the latest version of firmware or tune revision. For step by step instructions on how to update your SCT device, visit www.SCTFLASH.com and click on the Tech Support link. Make sure you have returned your vehicle back to stock before updating your unit. NOTE: If viewing this document online you can click on the following link to download the SCT Device Updater: SCT Device Updater 1.
SCT PERFORMANCE, LLC. 2. GETTING STARTED 2.1 Powering on the X4 There two ways to power on the device. If you’d like to flash your vehicle, you will need to use the Vehicle instructions below. If you are looking to update or load custom tunes onto your device, you will use the Computer instructions below. Using the Vehicle Locate the vehicle’s OBDII Diagnostic port. This connector is usually located under the vehicle’s dash board on the driver’s side.
SCT PERFORMANCE, LLC. 2.2 Loading Email Custom Tunes to the X4 1. Before connecting your X4 to your PC, go to www.sctflash.com and click on the Tech Support tab on the top of the page. Select the image of your device, then download and completely install the SCT Device Updater. 2. Using the provided USB cable, connect your device to the back of your computer. (Allow roughly 30 seconds for the drivers to install) 3. Save your custom tunes from your email to your desktop. 4.
SCT PERFORMANCE, LLC. 2.4 Using the Key Pad 2.5 Reading Vehicle Strategy Ford will often times update the computer in your vehicle. The new update ID (calibration ID) that is loaded into your computer is called a strategy. Many times your SCT dealer will ask you to read your vehicle’s strategy for many reasons which includes creating custom tunes. 1. Once the device is powered on using the OBDII cable provided. 2. Scroll down and select “VEHICLE INFO”.
SCT PERFORMANCE, LLC. 3.0 Programming your vehicle 3.1 Installing a Preloaded Tune File 1. Connect the X4 to your vehicle’s OBD II service port using the OBDII cable provided in the packaging. 2. With the unit powered on and connected to the vehicle, highlight and select the “Program Vehicle” option. 3. Next you will be prompted with a “Street Use Notice” which you must agree to. If you approve and agree, press the center button on the keypad to select “Continue” to proceed. 4.
SCT PERFORMANCE, LLC. How do I know what the Options do? In section 3.4 there is a list of options. The options and their functions and are also explained. For suggestions on using any of these options, refer to a custom tuning dealer. NOTE: Adjustable Options vary for each vehicle and are not available on all vehicles 3.2 Installing a Custom Tune File 1. Connect the X4 to your vehicle’s OBD II service port using the OBDII cable provided in the packaging. 2.
SCT PERFORMANCE, LLC. 3.3 Returning your Vehicle to Stock 1. Connect the X4 to your vehicle’s OBD II service port using the OBDII cable provided in the packaging. 2. With the unit powered on and connected to the vehicle, highlight and select the “Program Vehicle” option. 3. You will next see the “Street Use Notice” disclaimer, here you will be able to highlight and select “Return to Stock” at the bottom of the screen. (use the left arrow button to highlight) 4.
SCT PERFORMANCE, LLC. DIESEL AND GAS SHARED OPTIONS: EGR DELETE AXLE RATIO TIRE SIZE IDLE SPEED TRACTION CONTROL WOT SHIFT SHIFT PRESSURE Removes the check engine light caused by deleting EGR mechanically. Set axle ratio to correct shift patterns/speedometer. (Not available on all vehicles) Set tire size to correct shift patterns/speedometer. (Not available on all vehicles) Sets Idle speed in RPM. On/Off setting disables traction control without using the tcs button.
SCT PERFORMANCE, LLC. 4. USING DEVICE FEATURES 4.1 On-Device Data Logging and Monitoring This menu accesses the Monitoring and Data Logging feature. This menu is also used when collecting data from the analog input on the device. 1. With your key out of the ignition, connect your device to the OBDII port to power on your X4. Using the down arrow, highlight “Gauges/Datalog” and select it by pressing the center button on the keypad. 2.
SCT PERFORMANCE, LLC. 4.2 Connecting External Analog Inputs Using the wiring specifications that came with your analog sensor, connect to the proper pins using the diagram below. You will need to follow the on-device data logging instructions above to properly display the input. NOTE: Do not connect any device that exceeds 5 volts to the analog port or permanent damage to the adapter can occur. 4.
SCT PERFORMANCE, LLC. 5. COMMON QUESTIONS When I connect the tuner to the vehicle, it doesn’t power on. - Check for blown fuses for OBDII/Cigarette Lighter. Does the tuner have to stay plugged in to keep the vehicle tune? - No. After tuning, you can disconnect the programmer. Can I stack/combine the SCT programmer with another chip or tuning module? - All Chips/Tuning Products must be removed before tuning with SCT. Can I tune more than one vehicle with this programmer? - One vehicle tuned at a time.