ScreenBeam 1100 Model: SBWD1100 User Manual http://support.screenbeam.com | http://support.screenbeam.com/ticket Copyright © 2018 Actiontec Electronics, Inc. Version 1.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This user manual provides step-by-step instructions on how to setup and configure ScreenBeam receiver. After completing the steps described in this guide, you will be able to deploy the receiver in a meeting room or classroom site and provide users the ability to project wirelessly. Introduction ScreenBeam 1100 receiver can support wireless display for Windows 10/8.1/7, MacOS and iOS, and some Android devices. The receiver offers a couple methods for client device to connect.
This product is intended to be supplied by a UL Listed Direct Plug-In Power Unit marked “Class 2”, UL Listed Power Adapter or DC power source marked “L.P.S.” (or “Limited Power Source”) and rated 12Vdc, 3A minimum.
No network configuration is required for Wi-Fi Miracast capable device. However, you may need to verify the domain group policy and firewall settings to allow Wi-Fi Direct groups or adhoc connection. • Wireless display over LAN o ScreenBeam receiver § Ethernet connection: 100Mbps § Or Wi-Fi connection: 802.11n/ac (5GHz Non-DFS). Refer to the section below for instructions on how to setup wireless connection.
Setup Requirements • • • • ScreenBeam 1100 receiver TV/Projector/Monitor display with available HDMI input Ethernet network connection with DHCP IP (i.e. Wi-Fi router) (Required for wireless display over LAN and access to management console for configuration) ScreenBeam App (for Non-Miracast capable devices) http://support.screenbeam.com | http://support.screenbeam.com/ticket Copyright © 2018 Actiontec Electronics, Inc. Version 1.
A CONNECT SCREENBEAM RECEIVER TO A DISPLAY Figure 1 Receiver connection guide 1. Place the receiver next to a display of choice. 2. Using the provided HDMI cable, connect one end of the cable to the receiver’s HDMI port and the other end to the HDMI port of your display. 3. (Optional) If the display is supports interactive touch, you may connect the USB Type-B to Type-A “Touch” cable to the ScreenBeam receiver’s USB port. 4.
B UNDERSTANDING THE READY TO CONNECT SCREEN Figure 2 - Ready to Connect screen • • • Ready to Connect indicates the receiver is currently ready for a client device to connect and project wirelessly. Receiver name indicates the name that will be shown on the client device’s screen upon discovering the ScreenBeam receiver. Network information indicates the current version of the receiver and provides the most accurate information about the product for technical support.
C SETUP SCREENBEAM FOR NETWORK CONNECTION ScreenBeam receiver requires network connection for couple various functionalities; Wireless display over LAN and Central Management. You can connect the ScreenBeam receiver to the network via either wired or Wi-Fi connection. • • Wired connection If the network connection for ScreenBeam receiver provides a DHCP IP address, the Ready to Connect screen shall display a valid IP address under network status.
E SETUP SCREENBEAM FOR WIRELESS DISPLAY OVER LAN Under the Features webpage. • • • ScreenBeam App support is enabled by default for Mac/iOS and Win7 Enable AirPlay Mirroring for Mac/iOS support if needed. Note that security PIN is not supported for this mode. Enable Windows 10 Miracast over LAN support if needed. Note that security PIN is only supported by Win10 starting from build 1809 (and later). http://support.screenbeam.com | http://support.screenbeam.
F SCREENBEAM APP DOWNLOADS AND SETUP Note this is only required for Windows 7 device or Mac/iOS device in network that does not have multicast enabled. • • Get ScreenBeam App for your device here: http://www.screenbeam.com/downloads Install the ScreenBeam app G CONNECTING FROM YOUR DEVICE For the most updated instructions on how to connect, visit http://www.screenbeam.com/setup Congratulations! Your TV/Projector is now enabled with wireless display.
Appendix WALL MOUNT SPECIFICATIONS (VESA Mounting) The bottom of the receiver is equipped with four screw holes, with VESA dimensions of 75*75 mm. Firmly secure a VESA mount onto the receiver using four M4 screws (Maximum length: 8 mm, maximum torque: 6 kgf.cm). (figure not in scale) http://support.screenbeam.com | http://support.screenbeam.com/ticket Copyright © 2018 Actiontec Electronics, Inc. Version 1.
