User Guide

ManualsBrandsScreenBeam ManualsAccessories & Supplies(previously Actiontec) MyWirelessTV2 Wireless HD Transmitter & Receiver Extender – Wirelessly Connect HDMI-Enabled Media Device to HDTV or Projector Screen, Full HD 1080P, 150 Foot Range

Step 3D Turn on the TV and switch the source to the HDMI input that

the receiver is connected to.

Step 4A Plug the smaller end of the

power supply into the 5VDC port on the

back of the receiver.

Step 4B Plug the larger end of the

power supply into a power outlet.

Step 4C Make sure the power light

on the receiver is solid green.

Step 4D Wait for a bit as the

receiver connects to the transmitter.

The LINK light should be solid green

once they’re connected.

A. How MyWirelessTV Works

MyWirelessTV allows video and audio to be sent from video source to the

TV wirelessly. Therefore, you have the freedom to place the TV virtually

anywhere within the home and enjoy live TV without the wiring mess.

Identify which source device you want to connect to the transmitter. Video

from that source device will then be transmitted to your receiver box(es).

Installation for the MyWirelessTV is easy. Both units come pre-paired

to work with each other. All you need to do is connect the cables

according to the diagram or, if you want, follow the detailed step-by-step

instructions.

Note: Only use power adapter by Actiontec Electronics Inc., model number

WA-10P05FU.

B Setting up Transmitter and Receiver

Step 1A

Select the source device (i.e. a cable/satellite set-top box

or Blu-ray player) you wish to transmit signal to the TV, and power off that

device. Get the wireless HD video transmitter unit from MyWirelessTV 2

Kit and follow the steps below.

Note: If the transmitter and receiver are in the same room,

you may skip to Step 1C.

Step 1B (Optional) If the source device is

previously connected to an HDTV, unplug the

HDMI cable from the back of the source, then plug

the free end of the HDMI cable into the HDMI port

labeled Out-to-TV on the back of the transmitter.

Source

Device

Do NOT place the MyWirelessTV

Transmitter or Receiver on top of

or near a heat-generating source.

CAUTION

Please refer to

this illustration

while connect-

ing cables

Power

Outlet

Power

Outlet

TRANSMITTER MWTV2TX RECEIVER MWTV2RX

*Range subject to change.

Walls, ceilings and oors may

reduce the wireless range.

(Optional)

HDTV HDTV

Up to

150 ft.

range*

Step 1C Otherwise, get an HDMI

cable from the MyWirelessTV 2 Kit. Plug

one end into the HDMI Input port on the

back of the transmitter.

Step 1D Plug the other end of the

HDMI cable into the HDMI port on the

source device.

Step 2A Get the power supply from the

MyWirelessTV 2 Kit. Plug the smaller end of

the power supply into the 5VDC port on the

back of the transmitter.

Step 2B Plug the larger end of the

power supply into a power outlet.

Step 2C Verify the POWER light on

the transmitter is solid green.

Step 2D Now power on your video

source device.

Note: The LINK light will blink.

Step 3A Get the wireless HD video receiver, HDMI cable and

power supply. Go to the TV you want to connect.

Step 3B Plug one end of this HDMI

cable into an HDMI port on the HDTV.

Step 3C Plug the other end of the

HDMI cable into the HDMI port labeled

Out-to-TV on the back of the receiver.

CONTINUE ON NEXT SIDE

quick start guide ScreenBeam

MyWirelessTV 2

Summary of content (2 pages)

PAGE 1
ScreenBeam | MyWirelessTV 2 quick start guide A. How MyWirelessTV Works MyWirelessTV allows video and audio to be sent from video source to the TV wirelessly. Therefore, you have the freedom to place the TV virtually anywhere within the home and enjoy live TV without the wiring mess. ® B Setting up Transmitter and Receiver Step 1A Select the source device (i.e. a cable/satellite set-top box or Blu-ray player) you wish to transmit signal to the TV, and power off that device.
PAGE 2
ScreenBeam | MyWirelessTV 2 quick start guide C Setting Up IR Control The IR blaster cable connects to your wireless HD video transmitter. The IR blaster can receive IR signal from your source device’s remote control over the MyWirelessTV network, and emits the IR signal to control the source device. Thus, you can control the source device from wherever the TV and wireless HD video receiver are located. The IR receiver extension cable extends the IR receiver of the wireless HD video receiver.