Screen Service SDT 501 UB-C ARK 1-T Operations SDT 501 UB-C Software Defined Transposer/ Re-Transmitter OPERATION MANUAL 3 OPERATIONS CONTENTS INSTALLATION ...................................................................................................................................... 3 3.1 3.1.1 INSTALLATION PROCEDURE CHECK OFF..................................................................................... 3 3.1.2 SITE SELECTION ...............................................................
Screen Service SDT 501 UB-C ARK 1-T Operations 3.5.4 OUTPUT............................................................................................................................................ 68 3.6 NETWORK ........................................................................................................................................ 83 3.7 GPS ..................................................................................................................................................
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1 INSTALLATION 3.1.1 INSTALLATION PROCEDURE CHECK OFF Some procedures in this section contain steps preceded by a check box. Fill out or initial each step as it is completed. 3.1.2 SITE SELECTION Use the following specifications to establish criteria for site selection and equipment installation. 3.1.2.1 MOUNTING SPECIFICATIONS Mount.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1.4 EQUIPMENT MOUNTING Install the transmitter in an EIA (Standard 310) 19 inch rack as follows: Place the equipment into the rack (2 units), align the mounting holes, and secure in place with four rack screws. If configured to operate, make sure the "LINE" switch on the front panel of the POWER SUPPLY & METERING module is OFF. Connect the power cord to an operating power source.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1.5 FRONT PANEL 1 2 3 4 5 6 7 8 9 10 ARK 1-T Front Panel n. 1 Label RF INPUT 2 GPS IN 3 ASI OUTPUT HP 4 ASI OUTPUT LP 5 ASI in 1 6 ASI in 2 7 ASI in 3/ SDI in 8 ASI in 4 9 GBE 1 10 LCD Display May, 2010 Description v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1.5.1 REAR PANEL 1. AC Main ON/OFF SWITCH 2. AUX REMOTE 3. FAN 4. FAN 5. RF OUTPUT 6. FAN 7. 10 MHz INPUT 8. 1 PPS INPUT 9. AC MAIN INPUT SOKET 10. GND REFERENCE 11. RF MONITOR 1 2 7 9 May, 2010 3 4 5 6 8 10 11 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1.5.2 REAR PANEL CONNECTORS AUX REMOTE CONNECTOR Sub-D 25 Male. PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ASSIGNMENT Not used Alarm reset Remote STBY GND OPTO REMARKS in opto active to gnd in opto active to gnd SERIAL 485/232 SERIAL 485/232 RF OFF in opto active to gnd COM RL 0 RL 0 COM RL 1 RL 1 COM RL2 RL 2 COM RL 3 RL 3 NOR. CLOSED NOR. CLOSED NOR. CLOSED NOR. CLOSED Figure 3.
Screen Service May, 2010 SDT 501 UB-C ARK 1-T Operations v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1.6 MULTIMETER The following paragraphs describe the local user interface for ARK1. This user interface is composed of LCD Display, seven buttons and two status leds. Here below is depicted the ARK1 Front Panel. ESCAPE ON ALARM STANB-BY OK LEFT ARROW RIGHT ARROW UP ARROW DOWN ARROW • • • • • • • • • May, 2010 STAND-BY: push this button (lie in wait for two seconds) to put the equipment on STAND-BY mode.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.1.
Screen Service SDT 501 UB-C ARK 1-T Main display menu Operations LEGEND Menu System status Multiple choice Modulation Data R Network Data W Del Null Pcks Bandwidth Constellation Hierarchical Mode Interleaver HP FEC LP FEC FFT Guard Time Cell ID Time Slice HP Time Slice LP MPE FEC HP MPE FEC LP MPE FEC LP Delay Frec off Time off Net Delay Dev Delay May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Main display menu Operations LEGEND Menu System status Multiple choice Input Data R HP input Input Data W Lock Bitrate Useful Overflow Format Errors LP input Input Lock Bitrate Useful Overflow Format Errors Output Output RF status Frequency ref Channel Offset FWD power RFL power RTP 1 Input IP Address Status Input RTP 2 IP Address Status Alarms Alams list Reset system Yes No May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations Figure 1. Local Interface Menu Tree 3.1.8 BOOT AND WELCOME MESSAGE Turning on the equipment, the display shows the progress bar as follow: Screen Service ARK - DVB-T/DIG-IF System Init Init : [ ] Wait Screen Service ARK - DVB-T/DIG-IF Boot FPGA Init : [ ] Wait Screen Service ARK - DVB-T/DIG-IF Up Converter check Init : [ ] Wait Screen Service ARK - DVB-T/DIG-IF Start system Init : [ ] Wait When the boot is over, the board is ready.
Screen Service 3.2 SDT 501 UB-C ARK 1-T Operations IDLE MENU ARK - DVB T InHP: ASI1 Out 17.1dBm CH:22 UTC: 14:11 08/11/06 This menu appears after one minute waiting from the last touch. Information contained in the Idle Menu are described in next table. Table 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.2.1 MAIN MENU Change Mode Network setup System Status / / OK:Enter This menu shows five SUBMENUS. It is possible to view them sliding the menu up and down, with the UP or DOWN ARROWS, and to select one of them by pushing on the OK button. Submenus contained in the Main Menu are described in next table.
Screen Service 3.3 SDT 501 UB-C ARK 1-T Operations LCD alarms Through the LCD Alarms mask it is possible to select which alarm has to be notified on LCD display. The alarm button is lighted and when an alarm condition occurs, alarms status is displayed in the Alarms submenu. The following table lists the alarms messages displayed on LCD, associated to the corresponding alarm (refer to Alarms paragraph for further information about alarms and their masks). Alarms descriptions list Table 2.
Screen Service SDT 501 UB-C ARK 1-T Alarm Alarm Message FPGA Boot alarm FPGA boot err Warm up alarm Sys. warm up May, 2010 Operations v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4 JAVA REMOTE GRAPHIC USER INTERFACE The Java Graphic User Interface, stored in the board File System, is downloaded to the local PC every time the user connects to the board with a Web Browser. A proper Java Virtual Machine is needed; refer to the Appendix B for a description of supported Java and Internet Browsers. 3.4.1 JAVA INTERFACE OVERVIEW The following figure shows the main control switch of the Java User Interface.
Screen Service SDT 501 UB-C ARK 1-T Operations o GPS: shows received GPS statistics. o Alarms: provides a grid where to set alarms masks for LCD, Graphic User Interface, Events, Relays, Traps and RF Off. o Events: shows the board events log and allows the manual setting of date and. Figure 4.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.1.1 General Click on General button icon, highlighted in the nex figure, to access the general window. Figure 5. General window The General window provides a general description of the device and allows the access to a subset of commands through the following button icons: • Reset: resets the device. • LCD Standby: enables the LCD Stand-by button. • Download Software Standalone: performs a local download of the *.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.1.2 Input Click on Input button icon, highlighted in the nex figure, to access the input statistics window. Figure 6. Input window The Input window allows the monitoring of auxiliary inputs of Re-broadcasting DVB-T/H Modulator and Re-broadcasting ITU 470 modulator. Input Transport Streams monitoring of four ASI, two RTP channels on GBE port and two SDI are provided. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Table 3. Box Parameter / Control ASI Word rate ASI Bit-rate [bit/s] Operations Input window Description Admitted Ranges / Values ASI input word rate. 10 bits word rate of ASI input (Ref. to CEI EN 50083-9). Approximately 27 Mword/s ASI input bit-rate.
Screen Service Box Parameter / Control ASI Lock ASI ASI ASI/SDI Overflow Word Errors Equalizer Bypass SDT 501 UB-C ARK 1-T Description Admitted Ranges / Values ASI locking status.
Screen Service Box RTP Parameter / Control Filtered bitrate [bit/s] SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values Bit-rate actually used by the modulator. • Zero when the input is not selected • Equal to the total bit-rate, when Delete Null Packets disabled • Less than total bit-rate, when Delete Null Packets enabled RTP Format Transport Stream locking status.
Screen Service Box RTP RTP Parameter / Control Speed GbE errors SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values Ethernet connection speed. No duplex information is provided. • 10 Mbit//s • 100 Mbit//s • 1 Gbit//s Total amount of bad Ethernet frames received. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.1.3 Modes management &Seamless Switching Click on icon, highlighted in the nex figure, to access the tuner window. Figure 7. Modes Mangement& Seamless Switching This window provides commands that allow the selection of working modes, the management and selection of inputs, and the monitoring of quality and level of input RF signals.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.2 Modes management These commands allow the setting of working modes and switch selection rules. The following table shows the commands and indicators available for modes management. Figure 8. Modes Management May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations Table 4. Box System Mode & Auto-switching System Mode & Auto-switching Parameter / Control Actual mode Modes management Description Admitted Ranges / Values Selector of the switch mode rules. Switching modes rules Switch mode Refer to Auto-switching May, 2010 Manual Mode A • Mode B • Manual • Auto • Opto • Time • Mode A • Mode B paragraph for a detailed description of the switching rules and conditions.
Screen Service Box SDT 501 UB-C ARK 1-T Parameter / Control Operations Description Admitted Ranges / Values Time to wait for switching. Refer to Switching modes rules paragraph for a detailed description of the System Mode & Timeout Auto-switching setting switching rules. Autoswitch Auto-switching Timeout Input Alarm Auto-switching Delay [s] • Max: 255 s • Countdown from 255 to 0 • Min: 0.1 s • Max: 25.
Screen Service Box Mode A / Mode B SDT 501 UB-C ARK 1-T Parameter / Control HP input 1 Mode A / Mode B HP input 2 Mode A / Mode B LP input 1 Mode A / Mode B LP input 2 May, 2010 Operations Description Admitted Ranges / Values • ASI 1 • ASI 2 • ASI 3 • ASI 4 • GbE1 • GbE2 Selector of the input1 for re-modulator used for Not Hierarchical Modulation or High Priority. Selector of the input2 for re-modulator used for Not Hierarchical Modulation or High Priority.
Screen Service SDT 501 UB-C ARK 1-T Box Parameter / Control Mode A / Mode B Input ITU470 Mode A / Mode B Audio ITU470 Operations Description Admitted Ranges / Values • SDI 1 • SDI 2 • ch. 1,2 • ch. 3,4 • Checked: Use rule • Not checked: Do not use rule Selector of input ITU470. Selector of Audio ITU470. Switching modes rules Switching Rules No Input, No Mode A / B MIP May, 2010 Auto-switch alarms mask.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.3 Modes switching rules Four switching rules are provided in order to cover different requirements: • Manual: switch between mode A and mode B by selecting one mode using the Manual Selector. The selected mode is always enabled until the user selects the other one. • Auto: switch between mode A and mode B using the rules shown in the following table.
Screen Service May, 2010 SDT 501 UB-C ARK 1-T Operations v 1.
Screen Service SDT 501 UB-C ARK 1-T Table 6. Box Parameter / Control Operations Tuner management Description Admitted Ranges / Values Force input mode. If “None” option is selected, then the device operates the automatic seamless • None • Force Input 1 • Force Input 2 • No priority • Input 1 • Input 2 • Input 1 • Input 2 switching, using the selected priority input if available, and switching to the other input when the priority HP Input Force Input input is no more available.
Screen Service Box Parameter / Control SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values • Stop • Input 1 only • Input 2 only • Seamless • Wait • Min: 0 • Max: 9999999 • Checked: Alarm enabled • Not checked: Alarm not enabled This monitor shows the current device switch state. When both the two inputs are available, the input HP Input Switch State seamless switching is possible; else, if only one input is available, then the switching is no more available.
Screen Service Box Parameter / Control HP Input / Input 1 PAT CRC or Input 2 flag HP Input / Input 1 MIP CRC or Input 2 flag HP Input / Input 1 Sync Error or Input 2 flag HP Input / Input 1 Packet Jitter or Input 2 flag HP Input / Input 1 Transport or Input 2 Error flag SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values This flag enables the detection of CRC errors in the PAT to force a switching to the other input.
Screen Service Box Parameter / Control HP Input / Input 1 ASI Word or Input 2 Error flag HP Input / Input 1 MIP Priority or Input 2 Error flag SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values This flag enables the detection of the ASI Word Errors to force a switching to the other input.
Screen Service Box HP Input / Input 1 or Input 2 Parameter / Control PMT CRC Error SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked • Red: alarm raised PMT CRC Error rise this alarm HP Input / Input 1 o
Screen Service Box Parameter / Control SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values HP Input / Input 1 or Input 2 Network delay Error This alarm is raised when the TS Network delay is greater than the Maximum delay parameter, • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked • Red: alarm raised • Gray: alarm not present or masked extracted from its MIP HP Input /
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.5 MODULATION Click on Modulation button icon, highlighted in the nex figure, to access the modulation window. Figure 9. Modulation window: modulation parameters The Modulation window allows actual modulation parameters monitoring and modulator setting/monitoring. These settings are always editable but are applied only when the remodulator working mode is enabled. 3.4.
Screen Service SDT 501 UB-C ARK 1-T Table 7. Box Parameter/ Control Modulation management Description Admitted Ranges / Values Selector of Network’s Transmitters Synchronization. Network Synchronization parameter setting Refer to MFN / SFN Operations paragraph.
Screen Service Box Parameter/ Control SDT 501 UB-C ARK 1-T Description Admitted Ranges / Values Show the status of the MIP MIP Status Operations • No MIP • MIP OK • Wrong MIP priority • CRC Error • Network delay error • Min: 1 s • Max: 25.
Screen Service Box Parameter/ Control Test CW SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values • Checked: Enabled • Not checked: Disabled CW test enabling check box. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.7 Network Synchronization parameters setting Four Network Synchronization modes are available: • Multi Frequency Network mode using local parameters (MFN): The transmitter is not synchronized with any network. No input MIP is needed and Clock Reference can be internal. • Multi Frequency Network mode using MIP parameters (MFN MIP): The transmitter is not synchronized with any network but MIP sets the modulation parameters.
Screen Service Parameters SDT 501 UB-C ARK 1-T MFN SFN MFN + MIP Time Offset Local MIP or Local (only if enabled) Function from MIP can be enabled or disabled Del Null Packet Frequency Reference Can be enabled or disabled Can be internal or external MIP or Local (only if enabled) Function from MIP can be enabled or disabled Can be enabled or disabled Can be internal or external Must be disabled Must be external Operations SFN Local Local Must be disabled Must be external 3.4.
Screen Service SDT 501 UB-C ARK 1-T Table 9. Box Parameter/ Control Modulation parameters Description MIP Transmission mode: set by MIP. Local Transmission mode: locally set. Admitted Ranges / Values Mode Actual MIP • 2K • 4K • 8K • QPSK • 16-QAM • 64-QAM Current transmission mode Constellation Local Constellation for current modulation scheme: set by MIP. Constellation for current modulation scheme: locally set.
Screen Service Box Parameter/ Control SDT 501 UB-C ARK 1-T Description Actual Current bandwidth. MIP HP/LP stream code rate: set by MIP. Local HP/LP stream code rate: locally set. Admitted Ranges / Values HP/LP FEC Actual Operations • 1/2 • 2/3 • 3/4 • 5/6 • 7/8 • NH; • a=1; • a=2; • a=4. • 1/32 Current HP/LP stream code rate. MIP Hierarchy information for current scheme: set by MIP. Local Hierarchy information for current scheme: locally set.
Screen Service Box Parameter/ Control SDT 501 UB-C ARK 1-T Description May, 2010 Operations Admitted Ranges / Values v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.9 DVB-H parameters These commands and indicators allow the setting of options for DVB-H transmission, the monitoring of parameters carried by MIP in SFN configuration and of actual DVB-H options. Note: ARK-T read only the DVB-H parameters of HP input MIP Figure 12. May, 2010 DVB-H parameters v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations DVB-H parameters. Table 10. Box Parameter/ Control MIP Admitted Ranges / Values Description Enabling of time slice transmission of the HP/LP stream: set by MIP. Time Slicing Local HP/LP Actual Current enabling status of time slice transmission. MIP Local Enabling of time slice transmission of the HP/LP stream: locally set. HP/LP HP/LP MPE-FEC enabling: locally set. Current HP/LP MPE-FEC enabling status.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.10 MIP functions These commands and indicators allow the enabling and monitoring of MIP functions in SFN configuration, the setting of local functions and the monitoring of the actual functions used by modulator. Note: ARK-T read only the function of HP input MIP Figure 13. May, 2010 MIP functions v 1.
Screen Service Box Parameter / Control MIP SDT 501 UB-C ARK 1-T Description Operations Admitted Ranges / Values MIP cell ID function enabling • Checked: Enabled • Not checked: Disabled • Min: 0 • Max: 65,535 • Min: - 8388608 • Max: 8388607 • Min: 0 • Max: 9,999,999 Cell Id enable Local General Cell Id enabling. Must be enabled to insert Cell Id into output TPS. MIP Local MIP cell ID monitoring. Cell ID Actual MIP Local Local Cell ID setting. Used Cell ID monitoring.
Screen Service Box Parameter / Control MIP SDT 501 UB-C ARK 1-T Description Operations Admitted Ranges / Values • Checked: Enabled • Not checked: Disabled • Min: –500,000 Hz • Max: 500,000 Hz • Checked: Enabled • Not checked: Disabled • Min: –32,768 • Max: 32,767 MIP frequency offset function enabling and monitoring Freq. Offset [Hz] Local User frequency offset setting. Actual Used frequency offset monitoring.
Screen Service Parameter / Control Box MIP MIP MIP MIP MIP Tx Power [0.1dB] Func.Bw Function Cell ID enabled Function Tag Cell ID. Function Ch.
Screen Service Box MIP MIP MIP Local Local Parameter / Control Function Tag Ch.Bw SDT 501 UB-C ARK 1-T Description Admitted Ranges / Values It displays if the cell ID has to be inserted immediately (Grey) or after the receiving of the broadcasting Cell ID enable. Ch.
Screen Service Box Parameter / Control SDT 501 UB-C ARK 1-T Description Operations Admitted Ranges / Values • DVB-T o Checked: Enabled o Not checked: Disabled Local Standard User transmission standard setting. • DVB-H o Checked: Enabled o Not checked: Disabled Actual Actual Actual Center Freq. [Hz] HP Network Delay [100ns] LP Network Delay [100ns] Used center frequency indicator. Used HP input network delay indicator. Used LP input network delay indicator. May, 2010 v 1.
Screen Service Box SDT 501 UB-C ARK 1-T Parameter / Control Description Operations Admitted Ranges / Values Actual Device Delay Default device delay monitoring. [100ns] This value is added to the MIP max delay to calculate the Used delay • Min: - 8388608 • Max: 8388607 MIP functions Table 11. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.4.11 ITU functions These commands and indicators allow the enabling and monitoring of ITU functions. Figure 14. Box Parameter / Control ITU functions Description Admitted Ranges / Values • Checked: Enabled Test CW A/V Enable for CW on video and audio carriers. • Not checked: Disabled May, 2010 v 1.
Screen Service Box Parameter / Control Test Video Test Test Test Test Audio Test Tone Right [100 Hz] Tone Left [100 Hz] SDT 501 UB-C ARK 1-T Description Operations Admitted Ranges / Values • Bars • No Video Test • No Video Test • Audio Tone • Min: 0 • Max: 127 • Min: 0 • Max: 127 • Checked: Video test color bars enable. Audio test tones enable. Right tone frequency setting. Left tone frequency setting.
Screen Service Box Parameter / Control Test ITS 3 Test Test ITS 4 Enable ITS Insert SDT 501 UB-C ARK 1-T Description Operations Admitted Ranges / Values • Min: 7 • Max: 622 • Min: 7 • Max: 622 • Checked: Position of fixed line number 3 in output video. Position of fixed line number 4 in output video. Enabled Enable fixed lines insertion in output video. • Not checked: Disabled Modulation White Video white level setting.
Screen Service Box Modulation / Audio Modulation / Audio Modulation / Audio Modulation / Audio SDT 501 UB-C ARK 1-T Parameter / Control Deviation Description Operations Admitted Ranges / Values • Min: 0 • Max: 255 • MIN: –7 • MAX: –22 • Step: 0,1 • MIN: –7 • MAX: -–22 • Step: 0,1 • Mono Dual Audio deviation. Carrier Level 1 Audio 1 carrier level setting. [dB] Carrier Level 2 Audio 2 carrier level setting.
Screen Service Box Parameter / Control SDT 501 UB-C ARK 1-T Description Operations Admitted Ranges / Values PAL B, G • FM 5.5 / FM 5.742 PAL D, K Modulation Sound / Audio System Set the position of the two audio carriers. • FM 6.5 / FM 6.742 • FM 5.5 / FM 6.258 • Not checked: teletext not Modulation / Teletex Teletex Replace Enable replaced Replace enable for teletext. It is contained in elementary stream with above-specified PID.
Screen Service 3.5 SDT 501 UB-C ARK 1-T Operations PRE-CORRECTION TOOL The ARK1-T system provides a pre-correction tool for both Module & Phase and AM/PM output signal pre-correction. Remember to click on the Save as button the first time you change the factory default curves in order to do not overwrite them. Before closing the connection to port 5000, save curves changes otherwise they will be lost.
Screen Service SDT 501 UB-C ARK 1-T Operations Click two times the right mouse button on the grid to open the zoom menu. The “H” options are used to horizontally zoom (x01,x02,x04,x08,x16). The “V” options are used to vertically zoom (x01,x02,x04). During the saving actions are created two nonlinear pre-correction files: • *.dlin files: files containing digital coefficients values for Digital-IF linear pre-correction curves. • *.
Screen Service SDT 501 UB-C ARK 1-T Operations Knob points can be added with a left-click of the mouse on the grid and deleted with a right-click, drag and move a point to change the curve. Each coefficient variation, due to curves change, is saved in the FPGA “runtime” memory registers and dynamically changes the device’s output. The tool is prevented to send an “overflowing” amount of data to the device: curve changes will be applied only when the mouse button is released.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.5.3 Connection to port 5000 The connection to port 5000 is performed every time a pre-correction tool is opened through Mod.Pha. button and AM/PM button, from Java interface,.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.5.4 OUTPUT Click on Output button icon, highlighted in the nex figure, to access the output window. Figure 18. Output window Use the Output window to change Ethernet, RF output and ASI output settings, and to monitor all available hardware indicators. Differently from ARK1 and ARK1-R devices, the ASI outputs are here used as a direct bypass of the specified inputs. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations Output window Box Parameter / Control Description Admitted Ranges / Values Output RF signal enabling. The possible output RF signal status are the following: RF • ON; • RF OFF: automatic switch off of the output signal (refer to Amplifier status); • OFF: manual switch off of the output signal. ON / OFF • Green: ON • Green: RF OFF • Red: OFF • External • Internal • GPS Frequency reference source selector.
Screen Service Box RF AGC AGC SDT 501 UB-C ARK 1-T Parameter / Control Description Admitted Ranges / Values Internal Freq. Internal frequency reference fine tuning setting. Allows the fine tuning of VCO, internal clock oscillator, Ref. Tune with 60 Hz steps. AGC ON Mode Frequency Frequency Out [Hz] Out [Hz] May, 2010 Operations • Min: 0 • Max: 255 • Green: ON • Grey: OFF • Analog/Digital: AGC status. Current AGC mode indicator. It is always digital.
Screen Service Box Status May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control Ampli status Operations Description Admitted Ranges / Values Current amplifier status indicator. v 1.
Screen Service Box SDT 501 UB-C ARK 1-T Parameter / Control Operations Description Admitted Ranges / Values First PSU voltage indicator (values are expressed in V).
Screen Service Box Status SDT 501 UB-C ARK 1-T Parameter / Control PSU Temperature Status Fan 1 Status Fan 2 Status Fan 3 Status Fan 4 Status Status May, 2010 FWD Power [dBm] Reflex Power [dBm] Operations Description Admitted Ranges / Values PSU temperature indicator (values are expressed in °C). Fan 1 speed indicator (values are expressed in rpm). Used in SDTX20, SDTX50 and SDTX201 Fan 2 speed indicator (values are expressed in rpm).
Screen Service Box SDT 501 UB-C ARK 1-T Parameter / Control Operations Description Admitted Ranges / Values • Alarm: indicator of an alarm condition Opto & Relay Relay 0 Selector of Relay 0 mode. • Mode: indicator of operating mode • RF Status: indicator output RF signal status (on/off) • Opto & Relay Opto & Relay May, 2010 Relay 1 Relay 0…3 Alarm: indicator of an alarm condition Selector of Relay 1 mode.
Screen Service Box SDT 501 UB-C ARK 1-T Parameter / Control Operations Description Admitted Ranges / Values RF Off Opto status indicators. Opto 0 is a output RF manual on/off switch: Opto&Relay Opto 0 • • • Green: Closed (0) • Grey: Opened (1) • Green: Closed (0) • Grey: Opened (1) • Green: Closed (0) • Grey: Opened (1) Closed (0): RF on (default value) Opened (1): RF off Switch mode Opto status indicators.
Screen Service Box SDT 501 UB-C ARK 1-T Parameter / Control Operations Description Admitted Ranges / Values Stand-by enabling Opto status indicators: .( in version SDTX 20/50/201); Opto&Relay Opto 3 • Closed (0): stand-by off • Opened (1): stand-by on • Green: Closed (0) • Grey: Opened (1) Interlock Opto status indicators.(only in SDTX 501 version); • Closed (0): Interlock off • Opened (1): Interlock on Mode A / Mode B Channel Output channel.
Screen Service Box Mode A / Mode B FWD Power Thresholds FWD Power Thresholds Temperature Thresholds Temperature Thresholds RTP 1 May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control Offset [Hz] Operations Description Forward power warning threshold expressed in dBm. Alarm [dB] Forward power alarm threshold expressed in dBm. Warning Case temperature warning threshold expressed in °C. Alarm Case temperature alarm threshold expressed in °C.
Screen Service Box RTP 1 RTP 2 May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control Input Enable send frame Operations Description Admitted Ranges / Values • ASI 1 • ASI 2 • ASI 3 • ASI 4 • GbE1 • GbE2 • Seamless Output HP • Checked: Enabled • Not checked: Disabled Select which TS input shall be re-transmitted on RTP output channel 1. This selection is totally independent from the selection of the TS input of the modulator. Ethernet channels 2 transmission enabling. v 1.
Screen Service Box RTP 2 May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control Input Operations Description Admitted Ranges / Values • ASI 1 • ASI 2 • ASI 3 • ASI 4 • GbE1 • GbE2 • Seamless Output LP Select which TS input shall be re-transmitted on RTP output channel 2. This selection is totally independent from the selection of the TS input of the modulator. v 1.
Screen Service Box RTP 1 / RTP 2 May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control Status Operations Description Admitted Ranges / Values Select which TS input shall be re-transmitted on RTP output channel 1 and 2. • Resolving IP Addr. • IP not found • No entry • Transmitting data • Transmitting data multicast • No TS input • ON • OFF This selection is totally independent from the selection of the TS input of the modulator. v 1.
Screen Service Box ASI OUT HP May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control ASI OUT HP Operations Description Admitted Ranges / Values • ASI 1 • ASI 2 • ASI 3 • ASI 4 • GbE1 • GbE2 • Seamless Output HP Select which Transport Stream shall be re-proposed on device’s ASI output HP. This selection is totally independent from the selection of the TS input of the modulator. v 1.
Screen Service Box ASI OUT LP May, 2010 SDT 501 UB-C ARK 1-T Parameter / Control ASI OUT LP Operations Description Admitted Ranges / Values • ASI1 • ASI2 • ASI 3 • ASI 4 • GbE1 • GbE2 • Seamless Output LP Select which Transport Stream shall be re-proposed on device’s ASI output LP. This selection is totally independent from the selection of the TS input of the modulator. v 1.
Screen Service 3.6 SDT 501 UB-C ARK 1-T Operations NETWORK Click on Network button icon, highlighted in the nex figure, to access the Network management window. This window allows the Network management on both PRO-MPEG COP 3 RX and TX sides. It also allows the monitoring of the board IP and MAC addresses. Note: The Clock Recovery Function, used in MFN transmissions of received streams on Ethernet channels 1 and/or 2, is based on the timestamps of incoming packets.
Screen Service SDT 501 UB-C ARK 1-T Table 12. Box Local Local Parameter / Control Board IP address Board MAC address Local Gateway Local Mask Local Tx Source Port Trap IP address IGMP Input GbE Channel 1/2 Input GbE Channel 1/2 0…7 Enable IGMP IP Address Port Operations Network window Description Admitted Ranges / Values Board IP address. Board MAC address. Gateway address. Net Mask.
Screen Service Box Parameter / Control SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values • Input GbE Channel 1/2 Input GbE Channel 1/2 Protocol Bit-rate [bit/s] Ethernet input packets protocol. UDP/RTP: o Green: Detected o Grey: Not detected Bit-rate of TS from Ethernet input. • Zero when the input is not selected Input GbE Channel 1/2 Filtered bit-rate [bit/s] • Bit-rate actually used by the modulator.
Screen Service Box Input GbE Channel 1/2 Input GbE Channel 1/2 Input GbE Channel 1/2 Input GbE Channel 1/2 Gbe statistic Parameter / Control Lock Sequence error Overflow RTP Clock GBE Packets SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values Ethernet input lock status indicator.
Screen Service Box Gbe statistic Parameter / Control Speed Community Get Read community setting. Community Set Set community setting. Community Trap Trap community setting. Output GbE Enable send Channel 1/2 frame Output GbE Channel 1/2 IP Port Admitted Ranges / Values Ethernet speed.
Screen Service Box Output GbE Channel 1/2 Output GbE Channel 1/2 Output GbE Channel 1/2 Parameter / Control Status Destination MAC SSRC SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values • Resolving IP Addr. • IP not found • No entry • Transmitting data • Transmitting data multicast • No TS Input • ON • OFF Ethernet transmission on channel 1/2 status indicator. Destination MAC address. SSRC identifier of the RTP transmission on channel 1-2. May, 2010 v 1.
Screen Service Box Output GbE Channel 1/2 Output GbE Channel 1/2 Output GbE Channel 1/2 Parameter / Control TS Pck per Frame Frame type TS Format SDT 501 UB-C ARK 1-T Operations Description Admitted Ranges / Values • Min: 1 • Max: 7 • RTP • UDP • 188 Bytes • 240 Bytes Number of packets per frame. Transmission protocol selector. Transmission format. May, 2010 v 1.
Screen Service 3.7 SDT 501 UB-C ARK 1-T Operations GPS Click on GPS button icon, highlighted in the nex figure, to access the GPS received statistics window. Figure 19. May, 2010 GPS window v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations GPS window Table 13. Box Satellite Satellite Parameter/ Control #Number of Visible sat #Number of Tracked sat Description Admitted Ranges / Values Number of visible GPS satellites indicator. Number of tracked GPS satellites indicator. Alarms Satellite Alarm • Red: Alarm on • Grey: Alarm off • Green: Valid • Grey: Not valid GPS alarm status indicator. This alarm is a logic OR between the GPS alarms (refer to paragraph).
Screen Service 3.8 SDT 501 UB-C ARK 1-T Operations ALARMS Click on Alarms button icon, highlighted in the nex figure, to access the alarms management window. Figure 20. Alarms window The Alarm window allows the setting of alarm masks and the monitoring of alarms status. Use alarm masks to select how and which alarm have to be notified. Masks are organized in columns.
Screen Service SDT 501 UB-C ARK 1-T Table 14. Alarm Up converter Osc. Unlock Operations Alarms window Description and limitations Troubleshooting PLL of the Up converter board not locked to 120 MHz clock. • Hardware fault • Hardware fault • Hardware fault • Hardware fault • Hardware fault • Check alarm and warning thresholds • Lower the output power to decrease internal temperature Voltage out of range.
Screen Service Alarm Forward Power High Forward Power Low Warning Forward Power Low alarm Reflex Power High SDT 501 UB-C ARK 1-T Description and limitations Operations Troubleshooting • Check the device airflow • Check fans • Verify that the No RF Input alarm is enabled in the RF Off alarms mask Forward power goes over the maximum endurable limit.
Screen Service Alarm SDT 501 UB-C ARK 1-T Description and limitations Operations Troubleshooting • Verify that fans are not damaged; if they are, then substitute them.
Screen Service Alarm SDT 501 UB-C ARK 1-T Operations Description and limitations Troubleshooting communication error) is raised. • If the frequency reference is Internal: internal PLL fault • If the frequency reference is External: • o Internal PLL fault o Lack of external 10 MHz o Hardware fault If the frequency reference is GPS: o Internal PLL fault o 10 MHz line from the GPS receiver hardware fault 120 MHz is not locked.
Screen Service Alarm Signal 960 MHz Lock SDT 501 UB-C ARK 1-T Description and limitations Operations Troubleshooting 960 MHz is not locked. • Hardware fault • Check input signal • Check cable connection status • Hardware fault Seamless improper working warning An error has been detected on Logical seamless input.
Screen Service Alarm SDT 501 UB-C ARK 1-T Description and limitations Troubleshooting Seamless improper working warning Late MIP input alarm Operations • Check cable connections • Check Network delay • Hardware Fault • Check cable connections • Check Network delay • Hardware Fault • File system partition damage This alarm is high when the MIP in one of the seamless inputs of the current mode, is not in its expected position. This can be caused by a too high delay on the input.
Screen Service Alarm SDT 501 UB-C ARK 1-T Description and limitations Operations Troubleshooting One or more of the following files is missing in the File System. Bad File in File system • *.def; • *.sav; • *.dpwr; • *.apwr • • Check files list • Reload the file system *.dlin; • *.dpre; • *.apre • *.cfg; • *.gdly. • *.cdef May, 2010 v 1.
Screen Service Alarm SDT 501 UB-C ARK 1-T Operations Description and limitations Troubleshooting • If the frequency reference is Internal: internal PLL fault • If the frequency reference is External: o Internal PLL fault o Lack of external 1PPS o Hardware fault 1PPS is not lock to the selected frequency reference. This alarm’s RF OFF mask should always be enabled.
Screen Service Alarm SDT 501 UB-C ARK 1-T Description and limitations Operations Troubleshooting The internal counter, used to apply the System delay is not lock to 1 PPS. This alarm’s RF OFF mask should always be DVB-T System Delay enabled. • Check 1PPS • Hardware fault • Check input signal • Check input statistics • Restart the machine • Reload the file system Alarm raising limitations: The monitoring of this alarm is enabled only when the device has SFN modulation enabled.
Screen Service Alarm Warm up alarm SDT 501 UB-C ARK 1-T Description and limitations Operations Troubleshooting • Restart the machine • Temperature sensor fault Temperature level less than 5°C or temperature sensor fault. Notes to the table: • 0/1 stands for disabled/enabled and is fixed, X stands for not fixed. May, 2010 v 1.
Screen Service 3.9 SDT 501 UB-C ARK 1-T Operations EVENTS Click on Events button icon, highlighted in the nex figure, to access the events windos. Figure 21. Events window Open the Events window to slide the events list. Events are reported with the following information: • Time: event detection time. • Date: event detection date.
Screen Service • o SDT 501 UB-C ARK 1-T Event: event description; o System Init: system initialization, followed by the alarm in case of error. Operations Color: at different color is associated different kind of event: o Red: alarm event; o Green: command event; o Blue: system event; o Black: information event (It give more information about the former event). Use the following buttons, sited on the right side of the window, to manage the Events list: • Clear: resets the events list.
Screen Service SDT 501 UB-C ARK 1-T Operations Events list Table 15. Event Description Description RF OFF enabled from OPTO RF output switched off through OPTO 0. RF OFF disabled from OPTO RF output switched on through OPTO 0. Stand-by ON from OPTO Stand-by mode enabled through OPTO 3. Stand-by OFF from OPTO Stand-by mode disabled through OPTO 3. Stand-by ON from LCD Stand-by mode enabled through LCD button. Stand-by OFF Stand-by mode disabled through LCD button. New output power setting.
Screen Service SDT 501 UB-C ARK 1-T Event Description Operations Description This event is reported when one of the following alarms is raised: PS Restart N • Up converter Osc. Unlock • PS 28V out range • PS Current out of range • Absolute Power Limiter The fourth time one of the preceding alarms is risen the amplifier is restarted (from 1 up to 4 times). N: number of amplifier restarting. Only in SDTX 200 version.
Screen Service SDT 501 UB-C ARK 1-T Event Description SFN Re-Sync Operations Description A re-synchronization of internal counter occurred due to a difference with the STS parameter read from MIP. 3.9.1 Date and time setting The upper part of the event window shows the actual time and date and allows the manual setting of those parameters. Figure 22. Time and date setting Click to each part of the date and time to change the parameter and then increase or decrease its value with the up/down arrows.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.9.2 Task Error Event The watchdog performs a periodic (every 20 seconds) polling of tasks and triggers a system reset if one or more tasks do not answer, restarting the Codeloader (See Codeloader_Operations_Note_v1.1.doc for further information) and generating a TSK ERR event as follows: TSK ERR 00000028, 0000003c The blue underlined 8 bits word is the enabling status of the alarms mask.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.9.3 System Error Event For critical and fatal errors, the system calls the system error function and the SYS_ERR event is reported. The error code is described below: • 0x00: Out of memory. Memory pool size is too small. • 0x01: Invalid memory block release. Buffer data has been written out of boundaries of the allocated memory block. • 0x02: Link pointer corrupted. Buffer data has been written out of boundaries of the allocated memory block.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.9.4 System Initialization Event At every system initialization the event System Init is generated. This event is followed by 25 bytes specifying type and specific code of errors occurred during system initialization. Each byte refers to an error as described in the following table: Table 17. Byte 1° 2° 3° 4° 5° May, 2010 Init system event specific data Description FS_ERR Errors code • 0x00: File System ok.
Screen Service Byte SDT 501 UB-C ARK 1-T Description Operations Errors code • 0x00: FPGA boot ok. • 0x01: FPGA configuration erasing process error. • 0x02: Invalid configuration (the configuration has been correctly loaded, but the FPGA doesn’t boot). 6° BOOT_ERR FPGA boot error. • 0x10: FPGA file not found. • 0x11 and 0x20: Invalid FPGA file (syntax error). Please note that checked FPGA file is the one which refers to the selected mode.
Screen Service SDT 501 UB-C ARK 1-T Byte 8° Description Operations Errors code • 0x00: SNMP file ok. • 0x01: SNMP file not found. • 0x02: File open error. • 0x03: UDP socket initialization error. • 0x04: Port 161 open error. • 0x00: File ok. • 0x01: Current AGC mode file not found. • 0x02: Current AGC mode file open error. • 0x03…0x12: Invalid current AGC mode SNMP_ERR SNMP file error. file (syntax error). CALIB_ERR 9° *.apwr and *.
Screen Service SDT 501 UB-C ARK 1-T Byte Description PREC_ERR 10° Operations Errors code • 0x00: File ok. • 0x01: File not found. • 0x02: File open error. • 0x03…0x0a: Invalid file (syntax errors). *.apre and *.dpre files error. Please note that *.apre file is checked if device starts in AGC analog mode (rep. analog or ITU 470 mode), while *.dpre file is checked if device starts in AGC digital mode. LINEAR_ERR 11° • 0x00: File ok. • 0x01: File not found. • 0x02: File open error.
Screen Service SDT 501 UB-C ARK 1-T Byte 13° Description Operations Errors code • 0x00: Upconverter ready. • 0x01: Upconverter not found. • 0x02: Upconverter doesn’t correctly UPCV_ERR Upconverter error. answer. CH_FILT_ERR 14° • 0x10: Upconverter disabled. • 0x00: File ok. • 0x01: File not found. • 0x02: File open error. • 0x03…0x06: Invalid file (syntax errors). *.chf7 or *.chf8 file error. Please note that checked file is the one which refers to the current signal bandwidth: *.
Screen Service Byte SDT 501 UB-C ARK 1-T Description Operations Errors code • 0x00: File ok. • 0x01: File not found. • 0x02: File open error. • 0x03: syntax error or lack of input number of channels. • 0x13: syntax error or lack of output number of channels. • 0x04: input channels memory allocation error. • 0x14: output channels memory allocation error. 15° CH_DEF_ERR *.cdef file error. • 0x05: when the automatic indexing of channels listed in *.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.10 Option sub-menu The Option sub-menu allows two controls type: • Time: Time Read Interval [s]; • Alerts: the selection of events to display. 3.10.1 Time Figure 23. Time subwindow This control allows to change the device-to-management PC java update time. The default value is 2 seconds. Click on Close button quit this sub-window. 3.10.2 Alerts Figure 24.
Screen Service • SDT 501 UB-C ARK 1-T Operations o Board events. Typing error (yellow messages): o Typed setting is incorrect. Click on Close button to hide theses alert subwindows. Figure 25. Alert message Alert boxes can be disabled through the hide button located on the right side of the box. The hide button, once clicked, disables all boxes belonging to the same class. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.11 Download Software Standalone The Download Software Standalone button allows the downloading of standalone java application (executable jar file) based on java applet. If your browser is Internet Explorer, it may blocks the site from downloading files to your computer.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.12 SNMP – Simple Network Management Protocol The SNMP model assumes the existence of managers and agents. A manager is a software module in a management system responsible for managing the device. An agent is a software module in a managed device responsible for maintaining local management information and delivering that information to a manager via SNMP.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.13 SNMP Protocol Preferences Go to SNMP Protocol Preferences. The following parameters should be set in order to correctly configure the SNMP Manager: • SNMP protocol version: SNMPv1; • Read Community: the same of the one set in the Get field of Java interface, community section; • Set Community: the same of the one set in the Set field of Java interface, community section; • Timeout [s]: user defined; • Retransmits: user defined; • Port number: 161.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.14 Monitoring All status and setup information can be queried via SNMP. To get the setup and status information you need a management system (or a special MIB browser). Next figure, referring to MG-SOFT MIB Browser as an example, is a broad view of the ARK1-T tree structure. Figure 27. May, 2010 ARK1-T MIB Browser v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.15 OID Any status and setup information has an OID (Object Identifier). The OID of the ARK1-T system is: • screenservice_ARK1r: 1.3.6.1.4.1.21678.188 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).screenservice(21678).scree nservice_ARK1t(188) 3.15.1 SNMP tree structure The SNMP tree structure is shown in Figure 26, after the node screenserviceBroadcasting there is the node that specifies the device typology.
Screen Service OID 1 1.3 1.3.6 1.3.6.1 1.3.6.1.2 1.3.6.1.2.1 1.3.6.1.2.1.1 1.3.6.1.2.1.1.1 1.3.6.1.2.1.1.2 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.4 1.3.6.1.2.1.1.5 1.3.6.1.2.1.1.6 1.3.6.1.2.1.1.7 1.3.6.1.4 1.3.6.1.4.1 1.3.6.1.4.1.21678 1.3.6.1.4.1.21678.188 1.3.6.1.4.1.21678.188.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.1.10.6 1.3.6.1.4.1.21678.188.2 ark1t_Amplifier ark1t_Mode Operations R/W R Description Amplifier Serial Number 1.3.6.1.4.1.21678.188.2.1 ark1t_ModeSwitch RW 1.3.6.1.4.1.21678.188.2.2 ark1t_ModeManualSelector RW 1.3.6.1.4.1.21678.188.2.3 ark1t_ModeActual 1.3.6.1.4.1.21678.188.2.4 ark1t_ModeSelectorA RW 1.3.6.1.4.1.21678.188.2.5 ark1t_ModeSelectorB RW 1.3.6.1.4.1.21678.188.2.6 ark1t_ModeErrorFrequency 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.2.14.2 ark1t_SwitchingTimeMonth RW 1.3.6.1.4.1.21678.188.2.14.3 ark1t_SwitchingTimeDay RW 1.3.6.1.4.1.21678.188.2.14.4 ark1t_SwitchingTimeHour RW 1.3.6.1.4.1.21678.188.2.14.5 ark1t_SwitchingTimeMinutes RW 1.3.6.1.4.1.21678.188.2.14.6 ark1t_SwitchingTimeSeconds RW 1.3.6.1.4.1.21678.188.2.15 ark1t_InputSelectMode RW 1.3.6.1.4.1.21678.188.2.16 1.3.6.1.4.1.21678.188.3 1.3.6.1.4.1.21678.188.3.1 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.3.1.1.3 ark1t_InputSettingsA_Itu Operations R/W 1.3.6.1.4.1.21678.188.3.1.1.3.1 ark1t_SettingsA_Itu_Input RW 1.3.6.1.4.1.21678.188.3.1.1.3.2 1.3.6.1.4.1.21678.188.3.1.2 1.3.6.1.4.1.21678.188.3.1.2.1 ark1t_SettingsA_Itu_Audio_Ch ark1t_InputSettingsB ark1t_InputSettingsB_Rf RW 1.3.6.1.4.1.21678.188.3.1.2.1.1 ark1t_SettingsB_Rf_Channel RW 1.3.6.1.4.1.21678.188.3.1.2.1.2 1.3.6.1.4.1.21678.188.3.1.2.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.3.1.3.2 ark1t_EqualizerBypassAsi2 RW 1.3.6.1.4.1.21678.188.3.1.3.3 ark1t_EqualizerBypassAsi3Sdi1 RW 1.3.6.1.4.1.21678.188.3.1.3.4 1.3.6.1.4.1.21678.188.3.2 1.3.6.1.4.1.21678.188.3.2.1 ark1t_EqualizerBypassAsi4Sdi2 ark1t_InputStatistics ark1t_StatisticsRf RW Description enabled ASI 2 Eq. Bypass enable 0: disabled 1: enabled ASI 3 / SDI 1 Eq. Bypass enable 0: disabled 1: enabled ASI 4 / SDI 2 Eq.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.3.2.1.3.3 ark1t_STV0 Operations R/W 1.3.6.1.4.1.21678.188.3.2.1.3.3.1 ark1t_STV0LockTps R 1.3.6.1.4.1.21678.188.3.2.1.3.3.2 ark1t_STV0LockSyr R 1.3.6.1.4.1.21678.188.3.2.1.3.3.3 ark1t_STV0LockPunctureRate R 1.3.6.1.4.1.21678.188.3.2.1.3.3.4 ark1t_STV0LockDeinterleaver R 1.3.6.1.4.1.21678.188.3.2.1.3.3.5 ark1t_STV0DemodBerRate R 1.3.6.1.4.1.21678.188.3.2.1.3.3.6 ark1t_STV0ViterbiBerRate R 1.3.6.1.4.1.21678.188.3.2.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.3.2.1.3.3.12 ark1t_STV0Fec R 1.3.6.1.4.1.21678.188.3.2.1.3.3.13 ark1t_STV0Fft R 1.3.6.1.4.1.21678.188.3.2.1.3.3.14 ark1t_STV0GuardTime R 1.3.6.1.4.1.21678.188.3.2.1.3.3.15 1.3.6.1.4.1.21678.188.3.2.1.3.4 ark1t_STV0CelllId ark1t_STV1 R 1.3.6.1.4.1.21678.188.3.2.1.3.4.1 ark1t_STV1LockTps R 1.3.6.1.4.1.21678.188.3.2.1.3.4.2 ark1t_STV1LockSyr R 1.3.6.1.4.1.21678.188.3.2.1.3.4.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name 1.3.6.1.4.1.21678.188.3.2.1.3.4.9 ark1t_STV1Constallation R 1.3.6.1.4.1.21678.188.3.2.1.3.4.10 ark1t_STV1HierMode R 1.3.6.1.4.1.21678.188.3.2.1.3.4.11 ark1t_STV1Interleaver R 1.3.6.1.4.1.21678.188.3.2.1.3.4.12 ark1t_STV1Fec R 1.3.6.1.4.1.21678.188.3.2.1.3.4.13 ark1t_STV1Fft R 1.3.6.1.4.1.21678.188.3.2.1.3.4.14 ark1t_STV1GuardTime R 1.3.6.1.4.1.21678.188.3.2.1.3.4.15 1.3.6.1.4.1.21678.188.3.2.2 1.3.6.1.4.1.21678.188.3.2.2.1 1.3.6.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name 1.3.6.1.4.1.21678.188.3.2.2.1.1.5 ark1t_Asi1Lock R 1.3.6.1.4.1.21678.188.3.2.2.1.1.6 ark1t_Asi1PacketFormat R 1.3.6.1.4.1.21678.188.3.2.2.1.1.7 ark1t_Asi1Cd R 1.3.6.1.4.1.21678.188.3.2.2.1.1.8 1.3.6.1.4.1.21678.188.3.2.2.1.2 ark1t_Asi1Errors ark1t_Asi2 1.3.6.1.4.1.21678.188.3.2.2.1.2.1 ark1t_Asi2WordRate R 1.3.6.1.4.1.21678.188.3.2.2.1.2.2 ark1t_Asi2ByteRate R 1.3.6.1.4.1.21678.188.3.2.2.1.2.3 ark1t_Asi2Filtered R 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.3.2.2.1.4.5 ark1t_Asi4Lock R 1.3.6.1.4.1.21678.188.3.2.2.1.4.6 ark1t_Asi4PacketFormat R 1.3.6.1.4.1.21678.188.3.2.2.1.4.7 ark1t_Asi4Cd R 1.3.6.1.4.1.21678.188.3.2.2.1.4.8 1.3.6.1.4.1.21678.188.3.2.2.2 1.3.6.1.4.1.21678.188.3.2.2.2.1 1.3.6.1.4.1.21678.188.3.2.2.2.2 1.3.6.1.4.1.21678.188.3.2.2.2.3 ark1t_Asi4Errors ark1t_RemodGbe ark1t_GbePckCounter ark1t_GbeErrors ark1t_GbeChannel1 R R 1.3.6.1.4.1.21678.188.3.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.3.2.2.2.4.6 ark1t_GbeChannel2SequenceError R 1.3.6.1.4.1.21678.188.3.2.2.2.4.7 1.3.6.1.4.1.21678.188.3.2.3 1.3.6.1.4.1.21678.188.3.2.3.1 1.3.6.1.4.1.21678.188.3.2.3.1.1 ark1t_GbeChannel2Protocol ark1t_StatisticsItu ark1t_ItuSdi ark1t_Sdi1 R 1.3.6.1.4.1.21678.188.3.2.3.1.1.1 ark1t_Sdi1Lock R 1.3.6.1.4.1.21678.188.3.2.3.1.1.2 ark1t_Sdi1Cd R 1.3.6.1.4.1.21678.188.3.2.3.1.1.3 1.3.6.1.4.1.21678.188.3.2.3.1.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.3.3 1.3.6.1.4.1.21678.188.3.3.1 ark1t_InputSeamless ark1t_SeamlessHpInput Operations R/W 1.3.6.1.4.1.21678.188.3.3.1.1 ark1t_HpInputForceInput RW 1.3.6.1.4.1.21678.188.3.3.1.2 ark1t_HpInputPriorityInput RW 1.3.6.1.4.1.21678.188.3.3.1.3 ark1t_HpInputSelectedInput R 1.3.6.1.4.1.21678.188.3.3.1.4 1.3.6.1.4.1.21678.188.3.3.2 ark1t_HpInputSwitchState ark1t_SeamlessLpInput R 1.3.6.1.4.1.21678.188.3.3.2.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.3.3.3.1.3 ark1t_HpInput1MipCrcEn RW 1.3.6.1.4.1.21678.188.3.3.3.1.4 ark1t_HpInput1PatCrcEn RW 1.3.6.1.4.1.21678.188.3.3.3.1.5 ark1t_HpInput1AsiWordErrEn RW 1.3.6.1.4.1.21678.188.3.3.3.1.6 ark1t_HpInput1MipTypeErrEn RW 1.3.6.1.4.1.21678.188.3.3.3.1.7 1.3.6.1.4.1.21678.188.3.3.3.2 ark1t_HpInput1SyncErrEn ark1t_AlarmsMaskLpInput1 RW 1.3.6.1.4.1.21678.188.3.3.3.2.1 ark1t_LpInput1TransportErrEn RW 1.3.6.1.4.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.3.3.3.3.4 ark1t_HpInput2PatCrcEn RW 1.3.6.1.4.1.21678.188.3.3.3.3.5 ark1t_HpInput2AsiWordErrEn RW 1.3.6.1.4.1.21678.188.3.3.3.3.6 ark1t_HpInput2MipTypeErrEn RW 1.3.6.1.4.1.21678.188.3.3.3.3.7 1.3.6.1.4.1.21678.188.3.3.3.4 ark1t_HpInput2SyncErrEn ark1t_AlarmsMaskLpInput2 RW 1.3.6.1.4.1.21678.188.3.3.3.4.1 ark1t_LpInput2TransportErrEn RW 1.3.6.1.4.1.21678.188.3.3.3.4.2 ark1t_LpInput2PckJitterEn RW 1.3.6.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name 1.3.6.1.4.1.21678.188.3.3.4.1.5 ark1t_HpInput1PmtCrcErr R 1.3.6.1.4.1.21678.188.3.3.4.1.6 ark1t_HpInput1PatCrcErr R 1.3.6.1.4.1.21678.188.3.3.4.1.7 ark1t_HpInput1MipCrcErr R 1.3.6.1.4.1.21678.188.3.3.4.1.8 ark1t_HpInput1SyncErr R 1.3.6.1.4.1.21678.188.3.3.4.1.9 ark1t_HpInput1PckJitterErr R 1.3.6.1.4.1.21678.188.3.3.4.1.10 ark1t_HpInput1TransportErr R 1.3.6.1.4.1.21678.188.3.3.4.1.11 ark1t_HpInput1AsiWordErr R 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name 1.3.6.1.4.1.21678.188.3.3.4.2.9 ark1t_LpInput1PckJitterErr R 1.3.6.1.4.1.21678.188.3.3.4.2.10 ark1t_LpInput1TransportErr R 1.3.6.1.4.1.21678.188.3.3.4.2.11 ark1t_LpInput1AsiWordErr R 1.3.6.1.4.1.21678.188.3.3.4.2.12 ark1t_LpInput1NetworkDelayErr R 1.3.6.1.4.1.21678.188.3.3.4.2.13 1.3.6.1.4.1.21678.188.3.3.4.3 ark1t_LpInput1MipTypeErr ark1t_StatusHpInput2 R 1.3.6.1.4.1.21678.188.3.3.4.3.1 ark1t_HpInput2NetworkDelay R 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name 1.3.6.1.4.1.21678.188.3.3.4.3.12 ark1t_HpInput2NetworkDelayErr R 1.3.6.1.4.1.21678.188.3.3.4.3.13 1.3.6.1.4.1.21678.188.3.3.4.4 ark1t_HpInput2MipTypeErr ark1t_StatusLpInput2 R 1.3.6.1.4.1.21678.188.3.3.4.4.1 ark1t_LpInput2NetworkDelay R 1.3.6.1.4.1.21678.188.3.3.4.4.2 ark1t_LpInput2WatchdogErr R 1.3.6.1.4.1.21678.188.3.3.4.4.3 ark1t_LpInput2LateMipErr R 1.3.6.1.4.1.21678.188.3.3.4.4.4 ark1t_LpInput2NotValidErr R 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.4.1.2 1.3.6.1.4.1.21678.188.4.1.3 ark1t_DetectLp ark1t_PriorityError Operations R/W R 1.3.6.1.4.1.21678.188.4.1.3.1 ark1t_PriorityErrorHP R 1.3.6.1.4.1.21678.188.4.1.3.2 1.3.6.1.4.1.21678.188.4.1.4 ark1t_PriorityErrorLP ark1t_CRCError R 1.3.6.1.4.1.21678.188.4.1.4.1 ark1t_CRCErrorHP R 1.3.6.1.4.1.21678.188.4.1.4.2 1.3.6.1.4.1.21678.188.4.1.5 ark1t_CRCErrorLP ark1t_NetworkDelay R 1.3.6.1.4.1.21678.188.4.1.5.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.4.5 ark1t_MipAlpha R 1.3.6.1.4.1.21678.188.4.6 ark1t_MipGuardTime R 1.3.6.1.4.1.21678.188.4.7 ark1t_MipFft R 1.3.6.1.4.1.21678.188.4.8 1.3.6.1.4.1.21678.188.4.9 ark1t_MipBandwidth ark1t_MipFec R 1.3.6.1.4.1.21678.188.4.9.1 ark1t_MipFecHp R 1.3.6.1.4.1.21678.188.4.9.2 1.3.6.1.4.1.21678.188.4.10 ark1t_MipFecLp ark1t_MipTimeSlicing R 1.3.6.1.4.1.21678.188.4.10.1 ark1t_MipTimeSlicingHp R 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.4.16.2 1.3.6.1.4.1.21678.188.4.17 ark1t_TxPowerStatus ark1t_MipCellId Operations R/W R 1.3.6.1.4.1.21678.188.4.17.1 ark1t_CellIdEnable RW 1.3.6.1.4.1.21678.188.4.17.2 ark1t_CellIdFunctionEnable R 1.3.6.1.4.1.21678.188.4.17.3 1.3.6.1.4.1.21678.188.4.17.4 ark1t_CellIdFunctionTag ark1t_CellIdStatus R R 1.3.6.1.4.1.21678.188.4.17.5 1.3.6.1.4.1.21678.188.4.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.5.1.3.2 ark1t_LocalGuardTime RW 1.3.6.1.4.1.21678.188.5.1.3.3 ark1t_LocalAlpha RW 1.3.6.1.4.1.21678.188.5.1.3.4 1.3.6.1.4.1.21678.188.5.1.3.5 ark1t_LocalConstellation ark1t_LocalSettingsFec RW 1.3.6.1.4.1.21678.188.5.1.3.5.1 ark1t_SettingsFecHp RW 1.3.6.1.4.1.21678.188.5.1.3.5.2 ark1t_SettingsFecLP RW 1.3.6.1.4.1.21678.188.5.1.3.6 ark1t_LocalCellId RW 1.3.6.1.4.1.21678.188.5.1.3.7 1.3.6.1.4.1.21678.188.
Screen Service OID 1.3.6.1.4.1.21678.188.5.2.2 SDT 501 UB-C ARK 1-T Name ark1t_SettingsItu_Audio Operations R/W 1.3.6.1.4.1.21678.188.5.2.2.1 ark1t_SettingsItu_Audio_Deviation RW 1.3.6.1.4.1.21678.188.5.2.2.2 ark1t_SettingsItu_Audio_CarrierLevel1 RW 1.3.6.1.4.1.21678.188.5.2.2.3 ark1t_SettingsItu_Audio_CarrierLevel2 RW 1.3.6.1.4.1.21678.188.5.2.2.4 ark1t_SettingsItu_Audio_Emphasis 1.3.6.1.4.1.21678.188.5.2.2.5 ark1t_SettingsItu_Audio_Type RW 1.3.6.1.4.1.21678.188.5.2.2.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.6.1.1.3 1.3.6.1.4.1.21678.188.6.1.2 ark1t_SettingsAPower ark1t_OutputSettingsB RW 1.3.6.1.4.1.21678.188.6.1.2.1 ark1t_SettingsBChannel RW 1.3.6.1.4.1.21678.188.6.1.2.2 ark1t_SettingsBFrequencyOffset RW 1.3.6.1.4.1.21678.188.6.1.2.3 1.3.6.1.4.1.21678.188.6.1.3 1.3.6.1.4.1.21678.188.6.1.3.1 ark1t_SettingsBPower ark1t_OutputSettingsGbe ark1t_SettingsGbeTxCh1 RW 1.3.6.1.4.1.21678.188.6.1.3.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.6.1.4.2 1.3.6.1.4.1.21678.188.6.2 ark1t_InputToAsiOutLP ark1t_OutputRf RW RW RF output enable 0: disabled 1: enabled RF output status 0: off 1: on Pre-correction curve editing status 0: auto 1: manual Port 5000 status 0: closed 1: opened Current precorrection curve number Sets the precorrection curve number when the device is in Driver mode 0...
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.6.3.3.6 1.3.6.1.4.1.21678.188.6.3.3.7 ark1t_Test_Mute_Audio_Enable ark1t_Test_Itu_Its RW 1.3.6.1.4.1.21678.188.6.3.3.7.1 ark1t_Test_Its_enable RW 1.3.6.1.4.1.21678.188.6.3.3.7.2 ark1t_Test_Its0 RW 1.3.6.1.4.1.21678.188.6.3.3.7.3 ark1t_Test_Its1 RW 1.3.6.1.4.1.21678.188.6.3.3.7.4 ark1t_Test_Its2 RW 1.3.6.1.4.1.21678.188.6.3.3.7.5 ark1t_Test_Its3 RW 1.3.6.1.4.1.21678.188.6.3.3.7.6 1.3.6.1.4.1.21678.188.6.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.6.5.11 ark1t_modulator_monitor_interleaver R 1.3.6.1.4.1.21678.188.6.5.12 ark1t_modulator_monitor_system_delay R 1.3.6.1.4.1.21678.188.6.5.13 1.3.6.1.4.1.21678.188.6.5.14 ark1t_modulator_monitor_HP_network_delay ark1t_modulator_monitor_Fec R 1.3.6.1.4.1.21678.188.6.5.14.1 ark1t_FecHp R 1.3.6.1.4.1.21678.188.6.5.14.2 1.3.6.1.4.1.21678.188.6.5.15 ark1t_FecLp ark1t_modulator_monitor_MpeFec R 1.3.6.1.4.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.6.7.2.2 1.3.6.1.4.1.21678.188.7 ark1t_mipAntennaGain ark1t_HW_monitor 1.3.6.1.4.1.21678.188.7.1 ark1t_HW_monitor_RflPowerDbm R 1.3.6.1.4.1.21678.188.7.2 ark1t_HW_monitor_Amplifier R 1.3.6.1.4.1.21678.188.7.3 ark1t_HW_monitor_CurrentOut R 1.3.6.1.4.1.21678.188.7.4 ark1t_HW_monitor_PowerSupply R 1.3.6.1.4.1.21678.188.7.5 1.3.6.1.4.1.21678.188.7.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W Description Opto 2 status (Retry, only in 200 watt version) 0: closed 1: opened Opto 3 status (Stand-by): if closed the device is put on stand-by 0: closed 1: opened PS2 Current indicator (mA) 28/42V PS2 Voltage indicator (mV): 28V for 20W and 50W versions, and 42V for 200/500W version PS2 24V voltage indicator (mV), only in 200/500W version 1.3.6.1.4.1.21678.188.7.9.3 ark1t_Opto2Status R 1.3.6.1.4.1.21678.188.7.9.
Screen Service SDT 501 UB-C ARK 1-T OID Name 1.3.6.1.4.1.21678.188.10.3 ark1t_NetworkTxChannel1 Operations R/W 1.3.6.1.4.1.21678.188.10.3.1 ark1t_TxChannel1Type RW 1.3.6.1.4.1.21678.188.10.3.2 ark1t_TxChannel1TsFormat RW 1.3.6.1.4.1.21678.188.10.3.3 ark1t_TxChannel1TsNum RW 1.3.6.1.4.1.21678.188.10.3.4 ark1t_TxChannel1IpAddr RW 1.3.6.1.4.1.21678.188.10.3.5 ark1t_TxChannel1Port RW 1.3.6.1.4.1.21678.188.10.3.6 ark1t_TxChannel1Ssrc RW 1.3.6.1.4.1.21678.188.10.3.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.10.4.8 1.3.6.1.4.1.21678.188.10.5 ark1t_TxChannel2SourceClkReference ark1t_NetworkRxChannel1 RW 1.3.6.1.4.1.21678.188.10.5.1 ark1t_RxChannel1IpAddr RW 1.3.6.1.4.1.21678.188.10.5.2 ark1t_RxChannel1Port RW 1.3.6.1.4.1.21678.188.10.5.3 ark1t_RxChannel1ClkRecoveryEnable RW 1.3.6.1.4.1.21678.188.10.5.4 1.3.6.1.4.1.21678.188.10.6 ark1t_RxChannel1SourceClkReference ark1t_NetworkRxChannel2 RW 1.3.6.1.4.1.21678.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.11.1.3 ark1t_ThrRfSquelchB RW 1.3.6.1.4.1.21678.188.11.1.4 ark1t_ThrFwdPowerWarning RW 1.3.6.1.4.1.21678.188.11.1.5 ark1t_ThrFwdPowerAlarm RW 1.3.6.1.4.1.21678.188.11.1.6 ark1t_ThrTemperatureWarning RW 1.3.6.1.4.1.21678.188.11.1.7 ark1t_ThrTemperatureAlarm RW 1.3.6.1.4.1.21678.188.11.1.8 ark1t_ThrSNmodeA RW 1.3.6.1.4.1.21678.188.11.1.9 ark1t_ThrSNmodeB RW 1.3.6.1.4.1.21678.188.11.1.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name 1.3.6.1.4.1.21678.188.11.3.8 ark1t_TempWarningStatus R 1.3.6.1.4.1.21678.188.11.3.9 ark1t_FwdPowerHighStatus R 1.3.6.1.4.1.21678.188.11.3.10 ark1t_FwdPowerWarningStatus R 1.3.6.1.4.1.21678.188.11.3.11 ark1t_FwdPowerAlarmStatus R 1.3.6.1.4.1.21678.188.11.3.12 ark1t_ReflexPowerStatus R 1.3.6.1.4.1.21678.188.11.3.13 ark1t_FansSpeedStatus R 1.3.6.1.4.1.21678.188.11.3.14 ark1t_SnLevelStatus R 1.3.6.1.4.1.21678.188.11.3.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.11.3.33 ark1t_InputNotPresentStatus R 1.3.6.1.4.1.21678.188.11.3.34 ark1t_InputNotValidStatus R 1.3.6.1.4.1.21678.188.11.3.35 ark1t_LateMipStatus R 1.3.6.1.4.1.21678.188.11.3.36 1.3.6.1.4.1.21678.188.11.4 ark1t_NetworkDelayStatus ark1t_AlarmTrap R 1.3.6.1.4.1.21678.188.11.4.1 ark1t_Trap0Enable RW 1.3.6.1.4.1.21678.188.11.4.2 ark1t_Trap1Enable RW 1.3.6.1.4.1.21678.188.11.4.3 ark1t_Trap2Enable RW 1.3.
Screen Service SDT 501 UB-C ARK 1-T Operations OID Name R/W 1.3.6.1.4.1.21678.188.12.6.2 1.3.6.1.4.1.21678.188.12.6.3 1.3.6.1.4.1.21678.188.12.6.4 1.3.6.1.4.1.21678.188.12.6.5 1.3.6.1.4.1.21678.188.12.6.6 1.3.6.1.4.1.21678.188.13 ark1t_Month ark1t_Day ark1t_Hour ark1t_Minutes ark1t_Seconds ark1t_TrapAlarm RW RW RW RW RW Description 2000) Month setting Day setting Hour setting Minutes setting Seconds setting Alarm 3.
Screen Service SDT 501 UB-C ARK 1-T Operations There are six families of alarm masks: • ARK1r_AlarmJavaEnable: the selected alarms status is notified on the Java alarm page icon. • ARK1r_AlarmFrontPanelEnable: the selected alarms status is notified on LCD display lighting the alarm button and listing the alarms in the Alarms menu (refer to Alarms Menu paragraph).
Screen Service SDT 501 UB-C ARK 1-T Operations 3.17 Traps While a management station can poll, at fixed time interval, all the agents it knows for some key information, each agent is responsible for notifying the management station of any alarm condition. These events are communicated in SNMP messages known as traps. The following parameters should be set in order to correctly configure traps: • SNMP Agent Port: 162. • SNMP Agent Transport protocol: IP/UDP. • Variable o OID: 1.3.6.1.4.1.21678.188.
Screen Service May, 2010 SDT 501 UB-C ARK 1-T v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations Each trap carries a 32 bits word in which each alarm represents one bit (0: Off, 1: On). The following table shows the bit-to-alarm association. Bit-to-trap association map Table 19. Alarm Bit Alarm Bit Up converter Osc.
Screen Service Appendix A. SDT 501 UB-C ARK 1-T Operations Seamless input switching The Ark1-T device provides the functionality of seamless input auto-switching. This switching occurs between primary and secondary input selected, under the following restrictions: • The device is working in SFN mode; • The frequency reference selected is external or GPS; • The two inputs are both ASI, and contain the identical stream.
Screen Service Appendix B. SDT 501 UB-C ARK 1-T Operations Standalone/Driver working modes Two different working modes are provided: • Stand-alone: the device works in stand-alone mode. The system configuration can be totally set through user interfaces. Pre-correction curves are automatically selected according to channel and power range. • Driver: the device works in a driven system. The system configuration cannot be totally set through user interfaces.
Screen Service Appendix C. SDT 501 UB-C ARK 1-T Operations Installer Definitions feature The various Installer Definitions allows to support some different transmission standard definition, different working mode, power supply and power output in the first page of java interface are showed name and version of installer definition Following table explain the feature of each Installer Definitions May, 2010 v 1.
Screen Service Appendix D. SDT 501 UB-C ARK 1-T Operations Transport-level Protocols ARK 1 device allows connections over different ports and using different transport protocols over Gigabit Ethernet depending on functions and operations. In the following table used ports and protocols are listed to help users understand what software functions allow multiple connections and which port must be enabled. E.g.
Screen Service Appendix E. SDT 501 UB-C ARK 1-T Operations Application Note Screenshots of this application note are used as an example and shown file names are not related to ARK1-T device. E.1 How to update by installer 1. Launch the Java installer. Launch the Java Installer Figure 31. Java Installer 2. Insert the board IP address into the numeric field. Figure 32. Java Installer - IP Address insertion Insert the board IP Address May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3. Click on the “Search” button. Click on the “Search” button Figure 33. Java Installer - Search button 4. Select the device version you want to load. Select the version Figure 34. May, 2010 Java Installer - Device Version Selection v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 5. Click on the “Load” button. Click on the “Load” button Figure 35. May, 2010 Java Installer - Load button v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 6. If you want to update only some software versions, click on the check boxes corresponding to the software version you want to load, otherwise click on the check box corresponding to the Load All option. Click on the “Enter” button to start the loading. Figure 36. Java Installer - Software versions selection Select the “Load All” option Select one by one the software versions you want to load Click on the “Enter” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 7. Once started the loading, the “Stop” button lights up. Click on this button to end the programming. Figure 37. Java Installer - Stop button Click on the “Stop” button 8. When the loading is complete, the pop-up window “Operation Successfully Completed” appears. Click on the “OK” button. Figure 38. Java Installer - Operation Successfully Completed Click on the “OK” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations E.2 How to backup by installer 1. Launch the Java installer. Figure 39. Java Installer Launch the Java Installer 2. Insert the board IP address into the numeric field. Figure 40. Java Installer - IP Address insertion Insert the board IP Address May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 1. Click on the “Search” button. Figure 41. Java Installer - Search button Click on the “Search” button 2. Click on the “Backup” button. Figure 42. Java Installer – Backup button Click on the “Backup” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3. Select an existing destination folder and click on the “Save” button. Figure 43. Java Installer – Save button Click on the “Save” button 4. When the backup is complete, the pop-up window “Board System Backup saved in Destination Folder” appears. Click on the “OK” button. Figure 44. Java Installer - Operation Successfully Completed Click on the “OK” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations E.3 How to open the Java User Interface by installer 1. Launch the Java installer. Figure 45. Java Installer Launch the Java Installer 2. Insert the board IP address into the numeric field. Insert the board IP Address Figure 46. May, 2010 Java Installer - IP Address insertion v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3. Click on the “Search” button. Figure 47. Java Installer - Search button Click on the “Search” button 4. Click on the “Visit” button. Figure 48. Java Installer – Visit button Click on the “Visit” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 5. The Java User Interface will open automatically. Figure 49. May, 2010 Java User Interface – General window v 1.
Screen Service Appendix F. SDT 501 UB-C ARK 1-T Operations Java Virtual Machine The Java interface requires a host computer connected via Ethernet to the board with the proper Java Machine version installed. F.1 Ethernet connection The host computer has to be connected via Ethernet to the board. Direct or crossed UTP category 6 cable is recommended. NOTE: for best performances, a fast connection (i.e. gigabit Ethernet) is required.
Screen Service SDT 501 UB-C ARK 1-T Operations F.2.2 Java Control Panel Java caching must be disabled; to do that follow the following steps: 1. Open the PC general Control Panel and enter in the Java Control Panel 2. The following window will suddenly appear. Figure 50. Java Control Panel 3. Select “Settings…” in the “Temporary Internet Files” section of the “General” tab. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 4. Deselect the check box of the “Keep temporary files on my computer” (disable cache). Figure 51. Temporary Files Settings 5. Push “OK” button and close the window. F.3 Supported Web Browsers The Java GUI is designed to support every Web Browser that uses Sun Java Virtual Machine from 1.4.1 and newer. Here’s a list of Web Browsers where Java GUI has been tested and troubleshot: • Microsoft Internet Explorer, version 5 and newer.
Screen Service SDT 501 UB-C ARK 1-T Operations CH 22 TX A CH 2 : CH 60 2 X B CH 3 6 C CH 60: X Transposer CH 36 CH 40 Transposer Teansposer CH 40 CH 21 D E Transposer The Automatic Frequency Control in ARK1 devices is software defined. Most of the frequency drift errors could be avoided by means of a stable frequency reference, such as GPS, but since it is not always available, the ARK1 AFC makes it possible to compensate frequency jitters owing to each previous transposer.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.19 APPLICATION NOTE 3.19.1 How to update 9. Launch the Java installer. Figure 53. Java Installer Launch the Java Installer 10. Insert the board IP address into the numeric field. Figure 54. Java Installer - IP Address insertion Insert the board IP Address May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 11. Click on the “Search” button. Figure 55. Java Installer - Search button Click on the “Search” button 12. Select the device version you want to load. Figure 56. Select version Java Installer - Device Version Selection the May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 13. Click on the “Load” button. Click on the “Load” button Figure 57. May, 2010 Java Installer - Load button v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 14. If you want to update only some software versions, click on the check boxes corresponding to the software version you want to load, otherwise click on the check box corresponding to the Load All option. Click on the “Enter” button to start the loading. Figure 58. Java Installer - Software versions selection Select the “Load All” option Select one by one the software versions you want to load Click on the “Enter” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 15. Once started the loading, the “Stop” button lights up. Click on this button to end the programming. Figure 59. Java Installer - Stop button Click on the “Stop” button 16. When the loading is complete, the pop-up window “Operation Successfully Completed” appears. Click on the “OK” button. Figure 60. Java Installer - Operation Successfully Completed Click on the “OK” button May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 3.20 Java Virtual Machine The Java interface requires a host computer connected via Ethernet to the board with the proper Java Machine version installed. 3.21 ETHERNET CONNECTION The host computer has to be connected via Ethernet to the board. Direct or crossed UTP category 6 cable is recommended. 3.21.1 Configuration In order to connect to the board trough a LAN, all the devices have to be on the same network.
Screen Service SDT 501 UB-C ARK 1-T Operations 2. Perform a right button mouse click on the Java(TM) Platform icon sited on the right corner of the Taskbar and select “Open Control Panel”. The following window will suddenly appear. Figure 62. Java Control Panel 3. Select “Settings…” in the “Temporary Internet Files” section of the “General” tab. May, 2010 v 1.
Screen Service SDT 501 UB-C ARK 1-T Operations 4. Deselect the check box of the “Keep temporary files on my computer” (disable cache). Figure 63. Temporary Files Settings 5. Push “OK” button and close the window. 3.22 SUPPORTED WEB BROWSERS The Java GUI is designed to support every Web Browser that uses Sun Java Virtual Machine from 1.4.1 and newer. Here’s a list of Web Browsers where Java GUI has been tested and troubleshot: • Microsoft Internet Explorer, version 5 and newer.
