User's Manual

ManualsBrandsScosche Industries ManualsElectronicsBluetooth Carkit

(1) Speaker box

(2) Remote control

(3) Microphone

(4) Power connections

(5) Hardware bag

(6) Instruction manual

BT1000

HANDS-FREE BLUETOOTH

CAR KIT

WITH SPEAKER BOX

PARTS INCLUDED

TRANSFERRINg A mOBILE PHONE’S PHONEBOOK TO THE BT1000

With the BT1000 and mobile phone connected, press the “V-” for 3 seconds or until the

blue LED indictor comes on. The BT1000 will announce “Loading Phonebook. Please

wait”. The unit will continue to announce “Please wait” every 30 seconds until the process

is complete. When the phone transfer is complete the BT1000 will announce “Contacts

Saved” and the amount of SIM and phone memory remaining. If the memory is depleted

the BT1000 will prompt “Phonebook Full”. If the phonebook transfer is unsuccessful the

unit will announce “Loading Phonebook Failed”. Make sure your mobile phone supports the

transfer function. The BT1000 will store a maximum of 1000 phone numbers

OPERATION (cont’d)

REmOVINg PHONEBOOK ENTRIES

In standby mode, press and hold the “V+” and “V-” buttons simultaneously for 6 seconds.

The BT1000 will announce “Phonebook Deleted” and the entire phonebook will be de-

leted from the unit’s memory.

TURNINg ON/OFF THE TEXT-TO-SPEECH FUNCTION

In standby mode, press and hold the “V+” button for 6 seconds. “Voice Prompt On” or

“Voice Prompt Off” will be announced to denote the unit’s current status.

RESTORE DEFAULT SETTINgS

To restore the BT1000 to its original setting, press and hold the “V+” and “V-” buttons

simultaneously for 10 seconds until the blue LED ﬂashes rapidly. Press and hold the “V+”

and “V-” buttons simultaneously for 3 more seconds to power off the unit automatically.

When the process is complete the BT1000 will announce “Set Factory Default Complete”.

Scosche Industries Inc. warrants this product to be free from defects in material and workmanship for a period of 90 days

from purchase. This Scosche product is sold with the understanding that the purchaser has independently determined

the suitability of this product. This warranty is offered to the original purchaser of the product only. This warranty does not

cover the product if physically damaged, subject to negligence or misuse, abuse, alteration, accident, or an act of GOD.

This warranty does not apply to product which has water or physically damaged by accident or which has been misused,

disassembled or altered.

The original dated sales slip or proof of purchase will establish warranty eligibility. If the product should prove defective

within the warranty period, return the product with proof of purchase to Scosche Industries Inc. Scosche, at its option, will

replace or repair the product free of charge and return the product postage paid. In no event shall Scosche Industries, Inc.

be responsible for claims beyond the replacement value of the defective product, or in any way be liable or responsible

for consequential or incidental damages. No express warranties and no implied warranties, whether for ﬁtness or any

particular use or otherwise, except as set forth above (which is made expressly in lieu of all other warranties) shall apply

to products sold by Scosche. Scosche Industries cannot be held responsible for discrepancies/inconsistencies that may

occur due to automotive manufacturing changes or option.

LIMITED WARRANTY

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. Any changes or modiﬁcation

not expressly approved by the party responsible could void the user’s authority to operate the device.

FCC ID: IKQBT1000

This Category II radio communication device complies with Industry Canada Standard RSS-310 for RX Siren.

This device complies with part 15 of the FCC Rules and RSS-210 for TX remote control. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

Summary of content (4 pages)

PAGE 1
BT1000 OPERATION (cont’d) Transferring a mobile phone’s Phonebook to the BT1000 With the BT1000 and mobile phone connected, press the “V-” for 3 seconds or until the blue LED indictor comes on. The BT1000 will announce “Loading Phonebook. Please wait”. The unit will continue to announce “Please wait” every 30 seconds until the process is complete. When the phone transfer is complete the BT1000 will announce “Contacts Saved” and the amount of SIM and phone memory remaining.
PAGE 2
INSTALLATION OVERVIEW FIGURE 1 1. Primary mic location 2. Alternate mic location 3. Remote control location 4. Speaker box location INSTALLATION CAUTIONS & WARNINGS: BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE/BODY COMPUTER AND BATTERY). PLAN OUT YOUR INSTALLATION. You should pre-determine the location of the microphone, remote control andspeaker box. This will save time and ease the installation process.
PAGE 3
PAIRING, CONNECTION & DISCONNECTION TURNING ON/OFF ON: The BT1000 will switch on automatically when the ignition key is turned. Wait until you hear “Power on” and the blue LED indicator light is on for 3 seconds. To turn on/off manually press & hold MFB for 3 seconds. Press the “MFB” button for 3 seconds if you have turned the ignition key. Until you hear “power on” and the Blue LED indicator light 3secs. INSTALLATION FIGURE 2 OFF: The BT1000 will turn off automatically when the ignition is off.
PAGE 4
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.