DataPage MK2 Desktop UHF Radio Paging System Installation & User Manual Scope Communications UK Ltd, Quantum House, Steamer Quay, Totnes, Devon TQ9 5AL Tel: +44 1803 860700 Fax: +44 1803 863716 Email: sales@scope-uk.com Web: www.scope-uk.
Scope DataPage UHF MK2 Radio Paging System PREFACE Important Installation Information It is the purchasers’ responsibility to determine the suitability of this equipment and its derivatives for any given application, Scope cannot give specific advice in this manual, as each use will require independent evaluation. Scope has, wherever possible, employed extra safeguards to monitor the system’s performance.
Scope DataPage UHF MK2 Radio Paging System Preface Installation Installation must only be undertaken by an Approved contractor, who shall ensure that all work is carried out in compliance with National Wiring Regulations. For mains powered equipment, a readily accessible isolating fuse or switched socket must be located within 1 metre of the equipment.
Scope DataPage UHF MK2 Radio Paging System Contents of this box: DataPage Mk 2 UHF Base Station Plugtop Power Supply Internal Antenna Jack plug, locking, 3.5mm (2 off) User Manual Licence Application Form (RA5) Telephone interconnect lead (models NDPDTMF and NDPLP only) Supplied separately, to order: Numeric Display Pagers Optional External Aerial/Coaxial Cable (See Section: Other aerials) Please note you are required to obtain an OFCOM Licence to operate this equipment. See section under ‘Licensing’.
Scope DataPage UHF MK2 Radio Paging System Description: Your DataPage Mark 2 is supplied in one of three configurations: 1) NDP, the basic model, provides keyboard entry of data for message transmission. Additionally, two volt-free (dry) contacts are provided for sending pre-programmed messages. These contacts can be programmed for normally open, normally closed or change of state operation (see page 3, Dry Contacts).
Scope DataPage UHF MK2 Radio Paging System System Operation 1) Connect the 90 degree aerial to the BNC connector (bayonet twist lock) located at the side of the transmitter. Slide the plastic cover over the connector, engaging the two lugs into the corresponding recesses in the side of the case. This will maintain the aerial in an upright position, which is important for optimising the range of the transmitter. See Figure 1.
Scope DataPage UHF MK2 Radio Paging System Fig. 1 Connecting the antenna and locking cover Fig.
Scope DataPage UHF MK2 Radio Paging System Group Calls As previously stated, this system will accept pager identities from number 1 through 9,999. Most pagers will accept a minimum of two identities, enabling the pager to respond to selected group calls as well as its own unique identity.
Scope DataPage UHF MK2 Radio Paging System Program Parameters The standard models are factory pre-set and should not under any circumstances be adjusted by the customer. The factory settings can be viewed for the purposes of verification when ordering additional components etc. The system parameters are protected from accidental change by password control. To enter the system type: ( 72765 then press ENTER This is the default password.
Scope DataPage UHF MK2 Radio Paging System Pressing key 1 will display Normally Open Pressing key 2 will display Normally Closed Pressing key 3 will display Change of State After making your selection, press ENTER to store. Display will change to: TRIG. TIME 0-15: > This indicates the time that the contacts must remain in the active state to effect a trigger. A value of between 0 and 15 can be entered, which represents blocks of 0.25 seconds (approximately). Therefore, a value of 14 would equate to 3.
Scope DataPage UHF MK2 Radio Paging System 3: Phone (refer also to Section 2: Telephone Interface) This section is only applicable to models: NDPDTMF, NDPLP The telephone interface can be programmed through the keyboard as follows: Press key 3. The screen will change to display:RINGS TO ANSWER: >1 Select a number in the range 1-9 and press ENTER. This will define the number of rings before the system will pick up the line. Pressing CANCEL will abort the change and return you to the programming menu.
Scope DataPage UHF MK2 Radio Paging System 4: Serial After pressing ENTER, the display will change to: STOP BITS (1-2): >1 Enter a number in the range 1-2 to set. After pressing ENTER, the display will change to: Serial Port Set OK.
Scope DataPage UHF MK2 Radio Paging System Section 2 Telephone Interface (models NDPDTMF and NDPLP only) Overview IMPORTANT! For indirect connection to an internal PABX only. This unit must not under any circumstances be connected direct to the PSTN. The Scope digital paging interface can be used to transmit text or numeric messages from any telephone connected to your exchange, direct to the pocket of the individual being paged.
Scope DataPage UHF MK2 Radio Paging System Section 2 Telephone Interface (models NDPDTMF and NDPLP only) Numeric pagers STEP 1:- CONNECT TO SYSTEM DIAL PAGING SYSTEM EXTENSION NUMBER OR LINE PORT WAIT FOR SIGN-ON TONES (THREE NOTES ESCALATING LOW TO HIGH) STEP 2:- ENTER PAGER NUMBER (OR GROUP NO.) TO BE CALLED TYPE (PAGER NUMBER) TYPE Ä WAIT FOR ACCEPTANCE TONE OR PROCEED (SINGLE MID TONE) STEP 3: ENTER NUMERIC MESSAGE TO BE SENT COMPRISING 0,1,2,3,4,5,6,7,8,9.