User's Manual

ManualsBrandsScope Communications UK ManualsElectronicsPaging Transmitter

PREFACE

Important Information

It is the purchasers’ responsibility to determine the suitability of this equipment and its derivatives

for any given application, Scope cannot give specific advice in this manual, as each use will

require independent evaluation.

Scope has, wherever possible, employed extra safeguards or designed optional equipment to

further monitor the system’s performance. Certain system installations, operational requirements

or budgets may, however, limit the effectiveness of these safeguards. Again, the suitability of the

system for any given application must therefore be decided by the installer and their customer,

relative to the application and risk.

Licence

This equipment is cleared for use within the USA under a license assigned to the exclusive

importer, PIPS Holdings Inc. License No. 950415906. Certain restrictions apply in respect of

power output and antenna installations. Alternative frequencies are available by formal license

application (Form 600) via the FCC. These may not be subject to the same restrictions as the

dockside frequencies. Before operation you should obtain and read the FCC Rules and

Regulations, Title 47, Part 80 to End, including Parts 90 and 95, available from the US

Government Printing Office, GPO Bookstore or FCC Office.

Important Safety Information

Scope products are designed to operate safely when installed and used according to general

safety practices. The following requirements should be observed at all times.

Do NOT subject this equipment to:

Mechanical shock

Excessive humidity or moisture

Extremes of temperature

Corrosive liquids

This equipment must not be used in classified Hazardous Areas, including areas containing

explosive or flammable vapors, unless express authorization has been given in writing by the

manufacturer. If in doubt, consult your local product dealer for further information.

Only use a damp cloth for cleaning (not liquid or aerosol based cleaners), and ensure that any

power is removed from the unit(s) prior to beginning the cleaning operation.

Important Safety Information

Removal of covers from the equipment/chargers must only be undertaken by authorized service

personnel, who must ensure that power is isolated prior to removal.

Summary of content (6 pages)

PAGE 1
PREFACE Important Information It is the purchasers’ responsibility to determine the suitability of this equipment and its derivatives for any given application, Scope cannot give specific advice in this manual, as each use will require independent evaluation. Scope has, wherever possible, employed extra safeguards or designed optional equipment to further monitor the system’s performance.
PAGE 2
Preface Equipment Applications It is the user’s responsibility to determine the suitability of the Scope products for any given application. Scope or any of its subsidiaries or Distributors, cannot provide specific advice within this manual, as each application will require independent evaluation.
PAGE 3
Warranty This product is warranted as free from defects of workmanship and materials for a period of one year from the original purchase date. During this time, if there is a defect or malfunction of this product, Scope will, with proof of purchase, repair or replace at its discretion any defective parts, free of charge.
PAGE 4
Draft Manual for UHF Hand Held The Scope UHF Hand Held Digital transmitter has been designed to cover a wide range of applications across industry, from very simplistic press button calling to advanced automated monitoring of individuals who could be overcome by physical or other means and require to have calls sent to provide automated assistance. The equipment:- The Hand Held Transmitter A leather carry case A slot in fast charger A switch mode UL approved AC adapter for the charger.
PAGE 5
Portable Paging Aid This is the simplest of the applications of this unit. The operating cycle between charges will depend upon the duty cycle. However in what we assume will be a standard duty cycle the unit should operate for seven days or more before needing to be re-charged. The LCD display located on top of the transmitter will display ‘0’ when in standby mode. Two gray buttons are located adjacent to the LCD display and these will allow you to scroll up and down from 1 through to 99.
PAGE 6
If the unit is equipped with a motion sensor or accelerometer the unit is programmed to monitor the activity of the sensor. In the event that the conditions arise that would allow the processor to start a count down sequence to an alarm the following would occur. A period of inactivity would be selected when programming the device. This could be typically 30 seconds. If no activity is recorded within this period the onboard warning beeper would begin to emit an audible warning of an impending alarm.