MPS CARD READER Draft Copy 11 March 2019 User Guide 11 March 2019 SY-TP009200[B] ORIGINAL INSTRUCTIONS: ALL NON-ENGLISH EDITIONS OF THIS DOCUMENT ARE TRANSLATIONS OF THE ORIGINAL INSTRUCTIONS.
Draft Copy 11 March 2019 All ® notices signify marks registered in the United States. The look and feel of the games described and displayed herein and the individual components and displays of such games are trade dress of Scientific Games Corp. and its Subsidiaries. © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited. Confidential.
Draft Copy 11 March 2019 Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reference Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Draft Copy 11 March 2019 Preface Revision History Rev. A, 07 February 2019 - Initial release Rev. B, 11 March 2019 - Updated Industry Canada Notice and Marking to specify compliant components; added Bluetooth Antenna and U16 NFC frequency to Block Diagram Reference Information Revocation Bulletins, Service Manuals, and other documents are available online at https://www.sggaming.com/members/login. To request a login and password, select Request New Login.
Environmental Protection and Recycling Draft Copy 11 March 2019 Environmental Protection and Recycling This product bears a recycling mark in accordance with the Waste from Electrical Electronic Equipment (WEEE) European Commission Directive 2012/19/EU. This mark indicates that the product should be deposited at an appropriate facility to enable recovery and recycling in accordance with all applicable laws.
Draft Copy 11 March 2019 Compliance Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1 This device may not cause interference. 2 This device must accept any interference, including interference that may cause undesired operation of the device. NOTE To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.
Draft Copy 11 March 2019 MPS Card Reader Installation Overview This document details how to install the MPS Card Reader in an Electronic Gaming Machine (EGM).
Draft Copy 11 March 2019 Instructions 2 Secure the Player Tracking Panel to the MPS Front LED and NFC Assembly’s standoffs, Figure 2 (A), with three 4-40 Nuts, Figure 2 (B), using a 1/4-inch nut driver. Figure 2 MPS Front LED and NFC Assembly with Player Tracking Panel and 4-40 Nuts A B Figure 3 Front Bezel Assembly © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited.
Draft Copy 11 March 2019 Instructions Rear Board Installation Align the Rear Board, Figure 4 (A), with the Front Bezel Assembly and attach them by applying even force at their 40-pin connectors, Figure 5 (A) and Figure 6 (A). Figure 4 Front Bezel Assembly Aligned with Rear Board A Figure 5 40-pin Connector on MPS Front LED and NFC Assembly A © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited.
Draft Copy 11 March 2019 Instructions Figure 6 40-pin Connector on Solder Side of Rear Board A Figure 7 Front Bezel and Rear Board Assembly © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited.
Draft Copy 11 March 2019 Instructions Card Reader Body Installation 1 Align the three holes on the Adaptor Bezel, Figure 8 (A), of the Card Reader Body with the three standoffs, Figure 8 (B), protruding from the Front Bezel and Rear Board Assembly. Figure 8 Front Bezel and Rear Board Assembly Aligned with Card Reader Body A B 2 Secure the top standoff of the Front Bezel and Rear Board Assembly to the top of the Adaptor Bezel of the Card Reader Body with one 4-40 Nut using a 1/4-inch nut driver.
Draft Copy 11 March 2019 Instructions 3 Secure the two bottom standoffs of the Front Bezel and Rear Board Assembly to the bottom of the Adaptor Bezel of the Card Reader Body with two Collar Nuts, Figure 10 (A), using a 1/4-inch nut driver. CAUTION Do not over-tighten the Collar Nuts. This could bend the Rear Board and break its traces.
Draft Copy 11 March 2019 Instructions Body-to-Bezel Cable Installation NOTE Use one hand to stabilize the Card Reader Body. This will help prevent it from bending. 1 Insert either of the 14-pin connectors, Figure 12 (A), from the Body-to-Bezel Cable into the 14-pin connector, Figure 12 (B), at the rear of the MPS Card Reader Assembly.
Draft Copy 11 March 2019 Instructions USB Cable Installation 1 Insert the 7-pin connector, Figure 14 (A), of the USB Cable into the 7-pin connector, Figure 14 (B), on the Rear Board of the MPS Card Reader Assembly. • Gently and evenly apply pressure to the USB Cable connector while inserting it to prevent the Rear Board from bending.
Draft Copy 11 March 2019 Appendix Operation Properties Power Output 2.825 mW max Operating Frequency 2,402 - 2,480 MHz Operating Channel 40 channels, 0 - 39 Operating Mode GFSK Data Rate 500 kbs Intended Use To pair with consumers’ smart phones to enable player tracking Antenna Gain -1.8 dBi © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited.
Block Diagram Draft Copy 11 March 2019 Block Diagram © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited.
RF Schematic Draft Copy 11 March 2019 RF Schematic © 2019 Scientific Games Corp. and its Subsidiaries. All rights reserved. Unauthorized Distribution Prohibited.