User's Manual

ManualsBrandsScientech Electronics ManualsElectronicsDoor Sensor/ Glass Break Detector/ Flood Detector

ACCESSORIES

The LS-30 system includes a full range of accessories, so you can

customize many feature of your security system.

All the radio transmitters used in the LS-30 system, except the Remote

Controller, have a unique random code that is set by the factory with

16,777,216 combinations in total. Also with specially designed

transmission timing control, the LS-30 system can effectively prevent

mutual interference from other transmitters in the system. The Remote

Controller uses copy-preventing hopping-code technology, changing its

radio code every time you press the button. The combinations possible

through this hopping-code are up to 7.3 X 10

. To comply with the

regulations in most countries, radio power is limited to below 10mW, and

effective range is about 100 meters measured at open field. The range may

be somewhat less indoors, depending on the layout of building construction

and furniture.

You may enroll all the wireless accessories and change their related settings,

either through the guidance of the interactive LCD display on the Base Unit

explained in the “INSTALLATION” section that follows, or by using a

computer with the proprietary software “HyperSecureLink” through an

interface adapter, which offers a quicker and simpler way to perform the

installation in.

NOTE: The changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

The comply with the FCC RF exposure compliance requirements, this

device and its antenna must not be co-located or operating to conjunction

with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Summary of content (6 pages)

PAGE 1
ACCESSORIES The LS-30 system includes a full range of accessories, so you can customize many feature of your security system. All the radio transmitters used in the LS-30 system, except the Remote Controller, have a unique random code that is set by the factory with 16,777,216 combinations in total. Also with specially designed transmission timing control, the LS-30 system can effectively prevent mutual interference from other transmitters in the system.
PAGE 2
MAGNETIC CONTACT TRANSMITTER INTRODUCTION The TX-3DS is a fully supervised magnetic contact transmitter. With a built-in reed switch it can be used to secure doors and windows. Hole to reach TEST button inside Test Button LED Transmission LED Reed Sensor JP3 Tamper Switch Magnet Location Mark Aux. Input Terminals Fig. 1 Fig.2 Wiring Inlet Fig. 4 Fig.3 Fig.
PAGE 3
INSTALLATION A. Enrolling Code 1. Loosen the screw of the TX-3DS, then open the upper case and insert two AAA alkaline batteries. Important Notice: In order to reset the microprocessor properly before changing the batteries, please press TEST button for 5 seconds to discharge the energy that remains in the capacitors of TX-3DS. Otherwise, it may not restart after changing batteries. 2. Select “Installer Mode” on the Base Unit, and enter Installer Password to gain access authority. Then select \Set Device\E
PAGE 4
SPECIFICATIONS Supervision: sends heartbeat signal at 60-minute interval. When Tamper or Low Battery condition is detected, it reports automatically. Power Source: two AAA alkaline batteries. Current Drain: 5uA @ standby, 20mA @ operation Estimated Battery Life: 3 years (@ actuated 10 times/day) Transmitter Size: 20 x 29 x 123.
PAGE 5
GLASS BREAK DETECTOR INTRODUCTION The Glass Break Detector is composed of radio transmitter TX-3GS and detector GB. It sends an alarm signal to the Base Unit when the detector is triggered by the action of glass breaking. Test Button Tamper Switch Aux Input Wiring Inlet Detector Transmitter Fig. 1 Fig. 2 Transmitte Detector Fig. 3 INSTALLATION AND OPERATION 1. Loosen the screw of the radio transmitter TX-3GS, and open the cover. Use a pair of pliers or cutter to break the plastic of wiring inlet (Fig.
PAGE 6
FLOOD DETECTOR TX-3FS INTRODUCTION The Flood Detector is composed of Radio Transmitter TX-3FS and Detector FD. It sends an alarm signal to the Base Unit when the sensing probes of the detector are immersed in the water. Test Button Hole Wall Transmitter Wiring Inlet Fig. 1 Detector Holder Sensing probes Floor Fig. 2 INSTALLATION AND OPERATION 1. Loosen the screw of the radio transmitter TX-3FS and open the cover. Use a pair of pliers or cutter to break the plastic of the wiring inlet (Fig. 1).