User's Manual

ManualsBrandsScientech Electronics ManualsElectronicsMotion Detector

PIR MOTION DETECTOR

INTRODUCTION

The PIR-3SP Passive Infrared Detector detects the movement of human body heat within its effective

coverage; thus, when an intruder crosses or enters the area, the resulting change in infrared energy

from the intruder will be detected and an alarm signal will transmit to the Base Unit.

PET IMMUNE DETECTOR

 This detector is immune to one domestic pet up to 18 kg or 60 cm moving on the floor.

 If animal activity takes place above 1 meter high, the pet immunity allowance will be significantly

reduced. Therefore Do Not aim the detector at stairways that animal can pass.

 This detector should be mounted on the wall or corner at 2.0 m high and perpendicular to the

floor. Please note under this condition, the human motion within 1 m from the detector is

undetectable.

 Do NOT use any mounting bracket with swivel adjustment. Should you must use a bracket, it

should be used for horizontal alignment only, do not tilt down.

 Place the PCB at the “0” scale position. (for PCB version ST-IR-3B, or “P” scale for ST-IR-

3A).

And jumper JP5 at “PET” position.

 It’s a must to verify the pet immune function after installation. In case animal is detected, sliding

the PCB to +1~+2 scale to test again (for PCB version ST-IR-3B, or to -1~0 scale for ST-IR-3A).

 The weight of the animal can only be used as a reference. Other factors such as height and color

of fur could also affect the level of immunity.

IMPORTANT NOTE

To get the best sensitivity, PIR should be mounted to detect

movement of the intruder

across

a room rather than

toward

the

detector.

AAA Battery

X 2

Tamper

Switch

LED ON/OFF

Jumper

Pulse Count

Jumper

Test Switch

Reed Switch

PCB

Scale

Infrared Sensor

(Don’t touch)

PCB

Fixing

Screw

Jumper JP5

Fig. 1

Summary of content (6 pages)

PAGE 1
PIR MOTION DETECTOR INTRODUCTION The PIR-3SP Passive Infrared Detector detects the movement of human body heat within its effective coverage; thus, when an intruder crosses or enters the area, the resulting change in infrared energy from the intruder will be detected and an alarm signal will transmit to the Base Unit. AAA Battery X2 LED ON/OFF Jumper Tamper Switch Pulse Count Jumper Test Switch PCB Scale PCB Fixing Screw Jumper JP5 Reed Switch Fig.
PAGE 2
Do not install where the detector faces a window, since movement outside could cause unwanted alarms. Make sure the detection area does not have obstructions (curtains, screens, large pieces of furniture, plants, etc.) that could block the pattern of coverage. $ Avoid placing the sensor in areas containing objects likely to produce a rapid change in temperature, such as central heating radiators or ducts (or heaters of any kind), air conditioners, open flame, etc. Fig.
PAGE 3
WALK TEST It is essential to perform a walk test to verify optimum detection coverage. To do this, first hold the “TEST” button on the PIR-3SP board down for at least 3 seconds, until the LED turns ON→OFF→ ON, then release the button. Afterward, the PIR-3SP enters “TEST” mode for 3 minutes. Replace the cover of the PIR-3SP, then walk into the detection area at normal speed, while observing the LED indicator. The LED stays ON normally, and turns OFF when motion is detected.
PAGE 4
DETECTION PATTERN (PIR-3SP) Top View 110° Side View 2m 0.6m 1m 8m 12m SPECIFICATIONS Detector Type: dual element Coverage Angle: 110o Pet-immunity: Up to 18kg, 60cm high Effective Distance: max. 12 m @ ambient temp. 25℃ RFI Immunity: Ave. 20V/m (10~10000MHZ) Detectable Speed: 0.3~1.5m/sec.
PAGE 5
APPENDIX The PIR-3SP can be used as a conventional detector (non pet-immune) if changing lens to LN-N type (refer to Fig 6). And the model no. becomes PIR-3S. Note: 1. When you use LN-N lens, you must place JP5 at “NORL” position. 2. The detection patter of PIR-3S is as below (max. distance 15m), and you may adjust PCB scale position to fit detection coverage, or use bracket IRB-3 to adjust detection coverage. Besides, you may change the installation height properly.
PAGE 6
Manual-BackCover.